Merge branch 'spear/pinctrl' into next/pinctrl

This is a rebased version of some contents of
  git://git.stlinux.com/spear/linux-2.6.git spear-v3.5
which was accidentally sent against linux-next rather than an
-rc release.

The commits are based on other changes in the spear/dt branch
of the arm-soc tree that they depend on.

* spear/pinctrl:
  SPEAr3xx: Add pinctrl support for boards
  SPEAr: Remove existing padmux support for SPEAr
  pinctrl: Add SPEAr3xx pinctrl drivers
  pinctrl: Add SPEAr pinctrl drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/arm/SPEAr/overview.txt

@@ -17,14 +17,14 @@ Introduction
   SPEAr (Platform)
 	- SPEAr3XX (3XX SOC series, based on ARM9)
 		- SPEAr300 (SOC)
-			- SPEAr300_EVB (Evaluation Board)
+			- SPEAr300 Evaluation Board
 		- SPEAr310 (SOC)
-			- SPEAr310_EVB (Evaluation Board)
+			- SPEAr310 Evaluation Board
 		- SPEAr320 (SOC)
-			- SPEAr320_EVB (Evaluation Board)
+			- SPEAr320 Evaluation Board
 	- SPEAr6XX (6XX SOC series, based on ARM9)
 		- SPEAr600 (SOC)
-			- SPEAr600_EVB (Evaluation Board)
+			- SPEAr600 Evaluation Board
 	- SPEAr13XX (13XX SOC series, based on ARM CORTEXA9)
 		- SPEAr1300 (SOC)
 
@@ -51,10 +51,11 @@ Introduction
   Common file for machines of spear3xx family is mach-spear3xx/spear3xx.c and for
   spear6xx is mach-spear6xx/spear6xx.c. mach-spear* also contain soc/machine
   specific files, like spear300.c, spear310.c, spear320.c and spear600.c.
-  mach-spear* also contains board specific files for each machine type.
+  mach-spear* doesn't contains board specific files as they fully support
+  Flattened Device Tree.
 
 
   Document Author
   ---------------
 
-  Viresh Kumar, (c) 2010 ST Microelectronics
+  Viresh Kumar <viresh.kumar@st.com>, (c) 2010-2012 ST Microelectronics

Documentation/devicetree/bindings/arm/spear.txt

@@ -6,3 +6,21 @@ Boards with the ST SPEAr600 SoC shall have the following properties:
 Required root node property:
 
 compatible = "st,spear600";
+
+Boards with the ST SPEAr300 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear300";
+
+Boards with the ST SPEAr310 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear310";
+
+Boards with the ST SPEAr320 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "st,spear320";

Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt

+ST Microelectronics, SPEAr pinmux controller
+
+Required properties:
+- compatible	: "st,spear300-pinmux"
+		: "st,spear310-pinmux"
+		: "st,spear320-pinmux"
+- reg		: Address range of the pinctrl registers
+- st,pinmux-mode: Mandatory for SPEAr300 and SPEAr320 and invalid for others.
+	- Its values for SPEAr300:
+		- NAND_MODE		: <0>
+		- NOR_MODE		: <1>
+		- PHOTO_FRAME_MODE	: <2>
+		- LEND_IP_PHONE_MODE	: <3>
+		- HEND_IP_PHONE_MODE	: <4>
+		- LEND_WIFI_PHONE_MODE	: <5>
+		- HEND_WIFI_PHONE_MODE	: <6>
+		- ATA_PABX_WI2S_MODE	: <7>
+		- ATA_PABX_I2S_MODE	: <8>
+		- CAML_LCDW_MODE	: <9>
+		- CAMU_LCD_MODE		: <10>
+		- CAMU_WLCD_MODE	: <11>
+		- CAML_LCD_MODE		: <12>
+	- Its values for SPEAr320:
+		- AUTO_NET_SMII_MODE	: <0>
+		- AUTO_NET_MII_MODE	: <1>
+		- AUTO_EXP_MODE		: <2>
+		- SMALL_PRINTERS_MODE	: <3>
+		- EXTENDED_MODE		: <4>
+
+Please refer to pinctrl-bindings.txt in this directory for details of the common
+pinctrl bindings used by client devices.
+
+SPEAr's pinmux nodes act as a container for an abitrary number of subnodes. Each
+of these subnodes represents muxing for a pin, a group, or a list of pins or
+groups.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Required subnode-properties:
+- st,pins : An array of strings. Each string contains the name of a pin or
+  group.
+- st,function: A string containing the name of the function to mux to the pin or
+  group. See the SPEAr's TRM to determine which are valid for each pin or group.
+
+  Valid values for group and function names can be found from looking at the
+  group and function arrays in driver files:
+  drivers/pinctrl/spear/pinctrl-spear3*0.c
+
+Valid values for group names are:
+For All SPEAr3xx machines:
+	"firda_grp", "i2c0_grp", "ssp_cs_grp", "ssp0_grp", "mii0_grp",
+	"gpio0_pin0_grp", "gpio0_pin1_grp", "gpio0_pin2_grp", "gpio0_pin3_grp",
+	"gpio0_pin4_grp", "gpio0_pin5_grp", "uart0_ext_grp", "uart0_grp",
+	"timer_0_1_grp", timer_0_1_pins, "timer_2_3_grp"
+
+For SPEAr300 machines:
+	"fsmc_2chips_grp", "fsmc_4chips_grp", "clcd_lcdmode_grp",
+	"clcd_pfmode_grp", "tdm_grp", "i2c_clk_grp_grp", "caml_grp", "camu_grp",
+	"dac_grp", "i2s_grp", "sdhci_4bit_grp", "sdhci_8bit_grp",
+	"gpio1_0_to_3_grp", "gpio1_4_to_7_grp"
+
+For SPEAr310 machines:
+	"emi_cs_0_to_5_grp", "uart1_grp", "uart2_grp", "uart3_grp", "uart4_grp",
+	"uart5_grp", "fsmc_grp", "rs485_0_grp", "rs485_1_grp", "tdm_grp"
+
+For SPEAr320 machines:
+	"clcd_grp", "emi_grp", "fsmc_8bit_grp", "fsmc_16bit_grp", "spp_grp",
+	"sdhci_led_grp", "sdhci_cd_12_grp", "sdhci_cd_51_grp", "i2s_grp",
+	"uart1_grp", "uart1_modem_2_to_7_grp", "uart1_modem_31_to_36_grp",
+	"uart1_modem_34_to_45_grp", "uart1_modem_80_to_85_grp", "uart2_grp",
+	"uart3_8_9_grp", "uart3_15_16_grp", "uart3_41_42_grp",
+	"uart3_52_53_grp", "uart3_73_74_grp", "uart3_94_95_grp",
+	"uart3_98_99_grp", "uart4_6_7_grp", "uart4_13_14_grp",
+	"uart4_39_40_grp", "uart4_71_72_grp", "uart4_92_93_grp",
+	"uart4_100_101_grp", "uart5_4_5_grp", "uart5_37_38_grp",
+	"uart5_69_70_grp", "uart5_90_91_grp", "uart6_2_3_grp",
+	"uart6_88_89_grp", "rs485_grp", "touchscreen_grp", "can0_grp",
+	"can1_grp", "pwm0_1_pin_8_9_grp", "pwm0_1_pin_14_15_grp",
+	"pwm0_1_pin_30_31_grp", "pwm0_1_pin_37_38_grp", "pwm0_1_pin_42_43_grp",
+	"pwm0_1_pin_59_60_grp", "pwm0_1_pin_88_89_grp", "pwm2_pin_7_grp",
+	"pwm2_pin_13_grp", "pwm2_pin_29_grp", "pwm2_pin_34_grp",
+	"pwm2_pin_41_grp", "pwm2_pin_58_grp", "pwm2_pin_87_grp",
+	"pwm3_pin_6_grp", "pwm3_pin_12_grp", "pwm3_pin_28_grp",
+	"pwm3_pin_40_grp", "pwm3_pin_57_grp", "pwm3_pin_86_grp",
+	"ssp1_17_20_grp", "ssp1_36_39_grp", "ssp1_48_51_grp", "ssp1_65_68_grp",
+	"ssp1_94_97_grp", "ssp2_13_16_grp", "ssp2_32_35_grp", "ssp2_44_47_grp",
+	"ssp2_61_64_grp", "ssp2_90_93_grp", "mii2_grp", "smii0_1_grp",
+	"rmii0_1_grp", "i2c1_8_9_grp", "i2c1_98_99_grp", "i2c2_0_1_grp",
+	"i2c2_2_3_grp", "i2c2_19_20_grp", "i2c2_75_76_grp", "i2c2_96_97_grp"
+
+Valid values for function names are:
+For All SPEAr3xx machines:
+	"firda", "i2c0", "ssp_cs", "ssp0", "mii0", "gpio0", "uart0_ext",
+	"uart0", "timer_0_1", "timer_2_3"
+
+For SPEAr300 machines:
+	"fsmc", "clcd", "tdm", "i2c1", "cam", "dac", "i2s", "sdhci", "gpio1"
+
+For SPEAr310 machines:
+	"emi", "uart1", "uart2", "uart3", "uart4", "uart5", "fsmc", "rs485_0",
+	"rs485_1", "tdm"
+
+For SPEAr320 machines:
+	"clcd", "emi", "fsmc", "spp", "sdhci", "i2s", "uart1", "uart1_modem",
+	"uart2", "uart3", "uart4", "uart5", "uart6", "rs485", "touchscreen",
+	"can0", "can1", "pwm0_1", "pwm2", "pwm3", "ssp1", "ssp2", "mii2",
+	"mii0_1", "i2c1", "i2c2"

MAINTAINERS

@@ -5234,6 +5234,14 @@ M:	Linus Walleij <linus.walleij@linaro.org>
 S:	Maintained
 F:	drivers/pinctrl/
 
+PIN CONTROLLER - ST SPEAR
+M:	Viresh Kumar <viresh.kumar@st.com>
+L:	spear-devel@list.st.com
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+W:	http://www.st.com/spear
+S:	Maintained
+F:	driver/pinctrl/spear/
+
 PKTCDVD DRIVER
 M:	Peter Osterlund <petero2@telia.com>
 S:	Maintained
@@ -6330,21 +6338,6 @@ F:	arch/arm/mach-spear*/clock.c
 F:	arch/arm/plat-spear/clock.c
 F:	arch/arm/plat-spear/include/plat/clock.h
 
-SPEAR PAD MULTIPLEXING SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
-L:	spear-devel@list.st.com
-L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-W:	http://www.st.com/spear
-S:	Maintained
-F:	arch/arm/plat-spear/include/plat/padmux.h
-F:	arch/arm/plat-spear/padmux.c
-F:	arch/arm/mach-spear*/spear*xx.c
-F:	arch/arm/mach-spear*/include/mach/generic.h
-F:	arch/arm/mach-spear3xx/spear3*0.c
-F:	arch/arm/mach-spear3xx/spear3*0_evb.c
-F:	arch/arm/mach-spear6xx/spear600.c
-F:	arch/arm/mach-spear6xx/spear600_evb.c
-
 SPI SUBSYSTEM
 M:	Grant Likely <grant.likely@secretlab.ca>
 L:	spi-devel-general@lists.sourceforge.net

arch/arm/boot/dts/spear300-evb.dts

+/*
+ * DTS file for SPEAr300 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear300.dtsi"
+
+/ {
+	model = "ST SPEAr300 Evaluation Board";
+	compatible = "st,spear300-evb", "st,spear300";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@99000000 {
+			st,pinmux-mode = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				mii0 {
+					st,pins = "mii0_grp";
+					st,function = "mii0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				clcd {
+					st,pins = "clcd_pfmode_grp";
+					st,function = "clcd";
+				};
+				sdhci {
+					st,pins = "sdhci_4bit_grp";
+					st,function = "sdhci";
+				};
+				gpio1 {
+					st,pins = "gpio1_4_to_7_grp",
+						"gpio1_0_to_3_grp";
+					st,function = "gpio1";
+				};
+			};
+		};
+
+		clcd@60000000 {
+			status = "okay";
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		fsmc: flash@94000000 {
+			status = "okay";
+		};
+
+		gmac: eth@e0800000 {
+			status = "okay";
+		};
+
+		sdhci@70000000 {
+			int-gpio = <&gpio1 0 0>;
+			power-gpio = <&gpio1 2 1>;
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			gpio1: gpio@a9000000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+			       status = "okay";
+			};
+
+			kbd@a0000000 {
+				linux,keymap = < 0x00010000
+						 0x00020100
+						 0x00030200
+						 0x00040300
+						 0x00050400
+						 0x00060500
+						 0x00070600
+						 0x00080700
+						 0x00090800
+						 0x000a0001
+						 0x000c0101
+						 0x000d0201
+						 0x000e0301
+						 0x000f0401
+						 0x00100501
+						 0x00110601
+						 0x00120701
+						 0x00130801
+						 0x00140002
+						 0x00150102
+						 0x00160202
+						 0x00170302
+						 0x00180402
+						 0x00190502
+						 0x001a0602
+						 0x001b0702
+						 0x001c0802
+						 0x001d0003
+						 0x001e0103
+						 0x001f0203
+						 0x00200303
+						 0x00210403
+						 0x00220503
+						 0x00230603
+						 0x00240703
+						 0x00250803
+						 0x00260004
+						 0x00270104
+						 0x00280204
+						 0x00290304
+						 0x002a0404
+						 0x002b0504
+						 0x002c0604
+						 0x002d0704
+						 0x002e0804
+						 0x002f0005
+						 0x00300105
+						 0x00310205
+						 0x00320305
+						 0x00330405
+						 0x00340505
+						 0x00350605
+						 0x00360705
+						 0x00370805
+						 0x00380006
+						 0x00390106
+						 0x003a0206
+						 0x003b0306
+						 0x003c0406
+						 0x003d0506
+						 0x003e0606
+						 0x003f0706
+						 0x00400806
+						 0x00410007
+						 0x00420107
+						 0x00430207
+						 0x00440307
+						 0x00450407
+						 0x00460507
+						 0x00470607
+						 0x00480707
+						 0x00490807
+						 0x004a0008
+						 0x004b0108
+						 0x004c0208
+						 0x004d0308
+						 0x004e0408
+						 0x004f0508
+						 0x00500608
+						 0x00510708
+						 0x00520808 >;
+			       autorepeat;
+			       st,mode = <0>;
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear300.dtsi

+/*
+ * DTS file for SPEAr300 SoC
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x60000000 0x60000000 0x50000000
+			  0xd0000000 0xd0000000 0x30000000>;
+
+		pinmux@99000000 {
+			compatible = "st,spear300-pinmux";
+			reg = <0x99000000 0x1000>;
+		};
+
+		clcd@60000000 {
+			compatible = "arm,clcd-pl110", "arm,primecell";
+			reg = <0x60000000 0x1000>;
+			interrupts = <30>;
+			status = "disabled";
+		};
+
+		fsmc: flash@94000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x94000000 0x1000	/* FSMC Register */
+			       0x80000000 0x0010>;	/* NAND Base */
+			reg-names = "fsmc_regs", "nand_data";
+			st,ale-off = <0x20000>;
+			st,cle-off = <0x10000>;
+			status = "disabled";
+		};
+
+		sdhci@70000000 {
+			compatible = "st,sdhci-spear";
+			reg = <0x70000000 0x100>;
+			interrupts = <1>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xa0000000 0xa0000000 0x10000000
+				  0xd0000000 0xd0000000 0x30000000>;
+
+			gpio1: gpio@a9000000 {
+				#gpio-cells = <2>;
+				compatible = "arm,pl061", "arm,primecell";
+				gpio-controller;
+				reg = <0xa9000000 0x1000>;
+				status = "disabled";
+			};
+
+			kbd@a0000000 {
+				compatible = "st,spear300-kbd";
+				reg = <0xa0000000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear310-evb.dts

+/*
+ * DTS file for SPEAr310 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear310.dtsi"
+
+/ {
+	model = "ST SPEAr310 Evaluation Board";
+	compatible = "st,spear310-evb", "st,spear310";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@b4000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				gpio0 {
+					st,pins = "gpio0_pin0_grp",
+						"gpio0_pin1_grp",
+						"gpio0_pin2_grp",
+						"gpio0_pin3_grp",
+						"gpio0_pin4_grp",
+						"gpio0_pin5_grp";
+					st,function = "gpio0";
+				};
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				mii0 {
+					st,pins = "mii0_grp";
+					st,function = "mii0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				emi {
+					st,pins = "emi_cs_0_to_5_grp";
+					st,function = "emi";
+				};
+				fsmc {
+					st,pins = "fsmc_grp";
+					st,function = "fsmc";
+				};
+				uart1 {
+					st,pins = "uart1_grp";
+					st,function = "uart1";
+				};
+				uart2 {
+					st,pins = "uart2_grp";
+					st,function = "uart2";
+				};
+				uart3 {
+					st,pins = "uart3_grp";
+					st,function = "uart3";
+				};
+				uart4 {
+					st,pins = "uart4_grp";
+					st,function = "uart4";
+				};
+				uart5 {
+					st,pins = "uart5_grp";
+					st,function = "uart5";
+				};
+			};
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		fsmc: flash@44000000 {
+			status = "okay";
+		};
+
+		gmac: eth@e0800000 {
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate=<50000000>;
+
+			flash@f8000000 {
+				label = "m25p64";
+				reg = <0xf8000000 0x800000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				st,smi-fast-mode;
+			};
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+			};
+
+			serial@b2000000 {
+			       status = "okay";
+			};
+
+			serial@b2080000 {
+			       status = "okay";
+			};
+
+			serial@b2100000 {
+			       status = "okay";
+			};
+
+			serial@b2180000 {
+			       status = "okay";
+			};
+
+			serial@b2200000 {
+			       status = "okay";
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear310.dtsi

+/*
+ * DTS file for SPEAr310 SoC
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x40000000 0x40000000 0x10000000
+			  0xb0000000 0xb0000000 0x10000000
+			  0xd0000000 0xd0000000 0x30000000>;
+
+		pinmux@b4000000 {
+			compatible = "st,spear310-pinmux";
+			reg = <0xb4000000 0x1000>;
+		};
+
+		fsmc: flash@44000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x44000000 0x1000	/* FSMC Register */
+			       0x40000000 0x0010>;	/* NAND Base */
+			reg-names = "fsmc_regs", "nand_data";
+			st,ale-off = <0x10000>;
+			st,cle-off = <0x20000>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xb0000000 0xb0000000 0x10000000
+				  0xd0000000 0xd0000000 0x30000000>;
+
+			serial@b2000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2000000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@b2080000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2080000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@b2100000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2100000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@b2180000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2180000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@b2200000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2200000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear320-evb.dts

+/*
+ * DTS file for SPEAr320 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "spear320.dtsi"
+
+/ {
+	model = "ST SPEAr300 Evaluation Board";
+	compatible = "st,spear300-evb", "st,spear300";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@b3000000 {
+			st,pinmux-mode = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				mii0 {
+					st,pins = "mii0_grp";
+					st,function = "mii0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				sdhci {
+					st,pins = "sdhci_cd_51_grp";
+					st,function = "sdhci";
+				};
+				i2s {
+					st,pins = "i2s_grp";
+					st,function = "i2s";
+				};
+				uart1 {
+					st,pins = "uart1_grp";
+					st,function = "uart1";
+				};
+				uart2 {
+					st,pins = "uart2_grp";
+					st,function = "uart2";
+				};
+				can0 {
+					st,pins = "can0_grp";
+					st,function = "can0";
+				};
+				can1 {
+					st,pins = "can1_grp";
+					st,function = "can1";
+				};
+				mii2 {
+					st,pins = "mii2_grp";
+					st,function = "mii2";
+				};
+				pwm0_1 {
+					st,pins = "pwm0_1_pin_14_15_grp";
+					st,function = "pwm0_1";
+				};
+				pwm2 {
+					st,pins = "pwm2_pin_13_grp";
+					st,function = "pwm2";
+				};
+			};
+		};
+
+		clcd@90000000 {
+			status = "okay";
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		fsmc: flash@4c000000 {
+			status = "okay";
+		};
+
+		gmac: eth@e0800000 {
+			status = "okay";
+		};
+
+		sdhci@70000000 {
+			power-gpio = <&gpio0 2 1>;
+			power_always_enb;
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		spi1: spi@a5000000 {
+			status = "okay";
+		};
+
+		spi2: spi@a6000000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+			       status = "okay";
+			};
+
+			i2c1: i2c@a7000000 {
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+			};
+
+			serial@a3000000 {
+			       status = "okay";
+			};
+
+			serial@a4000000 {
+			       status = "okay";
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear320.dtsi

+/*
+ * DTS file for SPEAr320 SoC
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x40000000 0x40000000 0x80000000
+			  0xd0000000 0xd0000000 0x30000000>;
+
+		pinmux@b3000000 {
+			compatible = "st,spear320-pinmux";
+			reg = <0xb3000000 0x1000>;
+		};
+
+		clcd@90000000 {
+			compatible = "arm,clcd-pl110", "arm,primecell";
+			reg = <0x90000000 0x1000>;
+			interrupts = <33>;
+			status = "disabled";
+		};
+
+		fsmc: flash@4c000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x4c000000 0x1000	/* FSMC Register */
+			       0x50000000 0x0010>;	/* NAND Base */
+			reg-names = "fsmc_regs", "nand_data";
+			st,ale-off = <0x20000>;
+			st,cle-off = <0x10000>;
+			status = "disabled";
+		};
+
+		sdhci@70000000 {
+			compatible = "st,sdhci-spear";
+			reg = <0x70000000 0x100>;
+			interrupts = <29>;
+			status = "disabled";
+		};
+
+		spi1: spi@a5000000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0xa5000000 0x1000>;
+			status = "disabled";
+		};
+
+		spi2: spi@a6000000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0xa6000000 0x1000>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xa0000000 0xa0000000 0x10000000
+				  0xd0000000 0xd0000000 0x30000000>;
+
+			i2c1: i2c@a7000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0xa7000000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@a3000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xa3000000 0x1000>;
+				status = "disabled";
+			};
+
+			serial@a4000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xa4000000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear3xx.dtsi

+/*
+ * DTS file for all SPEAr3xx SoCs
+ *
+ * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&vic>;
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,arm926ejs";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+		vic: interrupt-controller@f1100000 {
+			compatible = "arm,pl190-vic";
+			interrupt-controller;
+			reg = <0xf1100000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		dma@fc400000 {
+			compatible = "arm,pl080", "arm,primecell";
+			reg = <0xfc400000 0x1000>;
+			interrupt-parent = <&vic>;
+			interrupts = <8>;
+			status = "disabled";
+		};
+
+		gmac: eth@e0800000 {
+			compatible = "st,spear600-gmac";
+			reg = <0xe0800000 0x8000>;
+			interrupts = <23 22>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			status = "disabled";
+		};
+
+		smi: flash@fc000000 {
+			compatible = "st,spear600-smi";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0xfc000000 0x1000>;
+			interrupts = <9>;
+			status = "disabled";
+		};
+
+		spi0: spi@d0100000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0xd0100000 0x1000>;
+			interrupts = <20>;
+			status = "disabled";
+		};
+
+		ehci@e1800000 {
+			compatible = "st,spear600-ehci", "usb-ehci";
+			reg = <0xe1800000 0x1000>;
+			interrupts = <26>;
+			status = "disabled";
+		};
+
+		ohci@e1900000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe1900000 0x1000>;
+			interrupts = <25>;
+			status = "disabled";
+		};
+
+		ohci@e2100000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe2100000 0x1000>;
+			interrupts = <27>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+			gpio0: gpio@fc980000 {
+				compatible = "arm,pl061", "arm,primecell";
+				reg = <0xfc980000 0x1000>;
+				interrupts = <11>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@d0180000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0xd0180000 0x1000>;
+				interrupts = <21>;
+				status = "disabled";
+			};
+
+			rtc@fc900000 {
+				compatible = "st,spear-rtc";
+				reg = <0xfc900000 0x1000>;
+				interrupts = <10>;
+				status = "disabled";
+			};
+
+			serial@d0000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xd0000000 0x1000>;
+				interrupts = <19>;
+				status = "disabled";
+			};
+
+			wdt@fc880000 {
+				compatible = "arm,sp805", "arm,primecell";
+				reg = <0xfc880000 0x1000>;
+				interrupts = <12>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/spear600-evb.dts

@@ -24,6 +24,10 @@ memory {
 	};
 
 	ahb {
+		dma@fc400000 {
+			status = "okay";
+		};
+
 		gmac: ethernet@e0800000 {
 			phy-mode = "gmii";
 			status = "okay";

arch/arm/boot/dts/spear600.dtsi

@@ -45,6 +45,14 @@ vic1: interrupt-controller@f1000000 {
 			#interrupt-cells = <1>;
 		};
 
+		dma@fc400000 {
+			compatible = "arm,pl080", "arm,primecell";
+			reg = <0xfc400000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <10>;
+			status = "disabled";
+		};
+
 		gmac: ethernet@e0800000 {
 			compatible = "st,spear600-gmac";
 			reg = <0xe0800000 0x8000>;

arch/arm/configs/spear3xx_defconfig

@@ -2,33 +2,67 @@ CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_PLAT_SPEAR=y
-CONFIG_BOARD_SPEAR300_EVB=y
-CONFIG_BOARD_SPEAR310_EVB=y
-CONFIG_BOARD_SPEAR320_EVB=y
+CONFIG_MACH_SPEAR300=y
+CONFIG_MACH_SPEAR310=y
+CONFIG_MACH_SPEAR320=y
 CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_MTD=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSMC=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_WLAN is not set
 CONFIG_INPUT_FF_MEMLESS=y
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_SPEAR=y
 # CONFIG_INPUT_MOUSE is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HW_RANDOM is not set
 CONFIG_RAW_DRIVER=y
 CONFIG_MAX_RAW_DEVS=8192
+CONFIG_I2C=y
+CONFIG_I2C_DESIGNWARE_PLATFORM=y
+CONFIG_SPI=y
+CONFIG_SPI_PL022=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_PL061=y
 # CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_ARM_SP805_WATCHDOG=y
+CONFIG_FB=y
+CONFIG_FB_ARMCLCD=y
 # CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
+CONFIG_USB=y
+# CONFIG_USB_DEVICE_CLASS is not set
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SPEAR=y
+CONFIG_RTC_CLASS=y
+CONFIG_DMADEVICES=y
+CONFIG_AMBA_PL08X=y
+CONFIG_DMATEST=m
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_SECURITY=y
@@ -39,8 +73,6 @@ CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
 CONFIG_TMPFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
@@ -48,6 +80,4 @@ CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
 CONFIG_DEBUG_INFO=y
-# CONFIG_CRC32 is not set

arch/arm/configs/spear6xx_defconfig

@@ -2,29 +2,58 @@ CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_PLAT_SPEAR=y
 CONFIG_ARCH_SPEAR6XX=y
-CONFIG_BOARD_SPEAR600_EVB=y
+CONFIG_BOARD_SPEAR600_DT=y
 CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_MTD=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_FSMC=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_WLAN is not set
 CONFIG_INPUT_FF_MEMLESS=y
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 CONFIG_RAW_DRIVER=y
 CONFIG_MAX_RAW_DEVS=8192
+CONFIG_I2C=y
+CONFIG_I2C_DESIGNWARE_PLATFORM=y
+CONFIG_SPI=y
+CONFIG_SPI_PL022=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_PL061=y
 # CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_ARM_SP805_WATCHDOG=y
 # CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_RTC_CLASS=y
+CONFIG_DMADEVICES=y
+CONFIG_AMBA_PL08X=y
+CONFIG_DMATEST=m
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_SECURITY=y
@@ -35,8 +64,6 @@ CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
 CONFIG_TMPFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NLS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
@@ -44,6 +71,4 @@ CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
 CONFIG_DEBUG_INFO=y
-# CONFIG_CRC32 is not set

arch/arm/mach-spear3xx/Kconfig

@@ -5,39 +5,22 @@
 if ARCH_SPEAR3XX
 
 menu "SPEAr3xx Implementations"
-config BOARD_SPEAR300_EVB
-	bool "SPEAr300 Evaluation Board"
-	select MACH_SPEAR300
-	help
-	  Supports ST SPEAr300 Evaluation Board
-
-config BOARD_SPEAR310_EVB
-	bool "SPEAr310 Evaluation Board"
-	select MACH_SPEAR310
-	help
-	  Supports ST SPEAr310 Evaluation Board
-
-config BOARD_SPEAR320_EVB
-	bool "SPEAr320 Evaluation Board"
-	select MACH_SPEAR320
-	help
-	  Supports ST SPEAr320 Evaluation Board
-
-endmenu
-
 config MACH_SPEAR300
-	bool "SPEAr300"
+	bool "SPEAr300 Machine support with Device Tree"
+	select PINCTRL_SPEAR300
 	help
-	  Supports ST SPEAr300 Machine
+	  Supports ST SPEAr300 machine configured via the device-tree
 
 config MACH_SPEAR310
-	bool "SPEAr310"
+	bool "SPEAr310 Machine support with Device Tree"
+	select PINCTRL_SPEAR310
 	help
-	  Supports ST SPEAr310 Machine
+	  Supports ST SPEAr310 machine configured via the device-tree
 
 config MACH_SPEAR320
-	bool "SPEAr320"
+	bool "SPEAr320 Machine support with Device Tree"
+	select PINCTRL_SPEAR320
 	help
-	  Supports ST SPEAr320 Machine
-
+	  Supports ST SPEAr320 machine configured via the device-tree
+endmenu
 endif #ARCH_SPEAR3XX

arch/arm/mach-spear3xx/Makefile

@@ -3,24 +3,13 @@
 #
 
 # common files
-obj-y	+= spear3xx.o clock.o
+obj-$(CONFIG_ARCH_SPEAR3XX)	+= spear3xx.o clock.o
 
 # spear300 specific files
 obj-$(CONFIG_MACH_SPEAR300) += spear300.o
 
-# spear300 boards files
-obj-$(CONFIG_BOARD_SPEAR300_EVB) += spear300_evb.o
-
-
 # spear310 specific files
 obj-$(CONFIG_MACH_SPEAR310) += spear310.o
 
-# spear310 boards files
-obj-$(CONFIG_BOARD_SPEAR310_EVB) += spear310_evb.o
-
-
 # spear320 specific files
 obj-$(CONFIG_MACH_SPEAR320) += spear320.o
-
-# spear320 boards files
-obj-$(CONFIG_BOARD_SPEAR320_EVB) += spear320_evb.o

arch/arm/mach-spear3xx/Makefile.boot

 zreladdr-y	+= 0x00008000
 params_phys-y	:= 0x00000100
 initrd_phys-y	:= 0x00800000
+
+dtb-$(CONFIG_MACH_SPEAR300)	+= spear300-evb.dtb
+dtb-$(CONFIG_MACH_SPEAR310)	+= spear310-evb.dtb
+dtb-$(CONFIG_MACH_SPEAR320)	+= spear320-evb.dtb

arch/arm/mach-spear3xx/clock.c

@@ -11,9 +11,11 @@
  * warranty of any kind, whether express or implied.
  */
 
+#include <linux/clkdev.h>
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
+#include <linux/of_platform.h>
 #include <asm/mach-types.h>
 #include <plat/clock.h>
 #include <mach/misc_regs.h>
@@ -411,6 +413,21 @@ static struct clk usbd_clk = {
 	.recalc = &follow_parent,
 };
 
+/* clock derived from usbh clk */
+/* usbh0 clock */
+static struct clk usbh0_clk = {
+	.flags = ALWAYS_ENABLED,
+	.pclk = &usbh_clk,
+	.recalc = &follow_parent,
+};
+
+/* usbh1 clock */
+static struct clk usbh1_clk = {
+	.flags = ALWAYS_ENABLED,
+	.pclk = &usbh_clk,
+	.recalc = &follow_parent,
+};
+
 /* clock derived from ahb clk */
 /* apb masks structure */
 static struct bus_clk_masks apb_masks = {
@@ -652,109 +669,126 @@ static struct clk pwm_clk = {
 
 /* array of all spear 3xx clock lookups */
 static struct clk_lookup spear_clk_lookups[] = {
-	{ .con_id = "apb_pclk",		.clk = &dummy_apb_pclk},
+	CLKDEV_INIT(NULL, "apb_pclk", &dummy_apb_pclk),
 	/* root clks */
-	{ .con_id = "osc_32k_clk",	.clk = &osc_32k_clk},
-	{ .con_id = "osc_24m_clk",	.clk = &osc_24m_clk},
+	CLKDEV_INIT(NULL, "osc_32k_clk", &osc_32k_clk),
+	CLKDEV_INIT(NULL, "osc_24m_clk", &osc_24m_clk),
 	/* clock derived from 32 KHz osc clk */
-	{ .dev_id = "rtc-spear",	.clk = &rtc_clk},
+	CLKDEV_INIT("fc900000.rtc", NULL, &rtc_clk),
 	/* clock derived from 24 MHz osc clk */
-	{ .con_id = "pll1_clk",		.clk = &pll1_clk},
-	{ .con_id = "pll3_48m_clk",	.clk = &pll3_48m_clk},
-	{ .dev_id = "wdt",		.clk = &wdt_clk},
+	CLKDEV_INIT(NULL, "pll1_clk", &pll1_clk),
+	CLKDEV_INIT(NULL, "pll3_48m_clk", &pll3_48m_clk),
+	CLKDEV_INIT("fc880000.wdt", NULL, &wdt_clk),
 	/* clock derived from pll1 clk */
-	{ .con_id = "cpu_clk",		.clk = &cpu_clk},
-	{ .con_id = "ahb_clk",		.clk = &ahb_clk},
-	{ .con_id = "uart_synth_clk",	.clk = &uart_synth_clk},
-	{ .con_id = "firda_synth_clk",	.clk = &firda_synth_clk},
-	{ .con_id = "gpt0_synth_clk",	.clk = &gpt0_synth_clk},
-	{ .con_id = "gpt1_synth_clk",	.clk = &gpt1_synth_clk},
-	{ .con_id = "gpt2_synth_clk",	.clk = &gpt2_synth_clk},
-	{ .dev_id = "uart",		.clk = &uart_clk},
-	{ .dev_id = "firda",		.clk = &firda_clk},
-	{ .dev_id = "gpt0",		.clk = &gpt0_clk},
-	{ .dev_id = "gpt1",		.clk = &gpt1_clk},
-	{ .dev_id = "gpt2",		.clk = &gpt2_clk},
+	CLKDEV_INIT(NULL, "cpu_clk", &cpu_clk),
+	CLKDEV_INIT(NULL, "ahb_clk", &ahb_clk),
+	CLKDEV_INIT(NULL, "uart_synth_clk", &uart_synth_clk),
+	CLKDEV_INIT(NULL, "firda_synth_clk", &firda_synth_clk),
+	CLKDEV_INIT(NULL, "gpt0_synth_clk", &gpt0_synth_clk),
+	CLKDEV_INIT(NULL, "gpt1_synth_clk", &gpt1_synth_clk),
+	CLKDEV_INIT(NULL, "gpt2_synth_clk", &gpt2_synth_clk),
+	CLKDEV_INIT("d0000000.serial", NULL, &uart_clk),
+	CLKDEV_INIT("firda", NULL, &firda_clk),
+	CLKDEV_INIT("gpt0", NULL, &gpt0_clk),
+	CLKDEV_INIT("gpt1", NULL, &gpt1_clk),
+	CLKDEV_INIT("gpt2", NULL, &gpt2_clk),
 	/* clock derived from pll3 clk */
-	{ .dev_id = "designware_udc",   .clk = &usbd_clk},
-	{ .con_id = "usbh_clk",		.clk = &usbh_clk},
+	CLKDEV_INIT("designware_udc", NULL, &usbd_clk),
+	CLKDEV_INIT(NULL, "usbh_clk", &usbh_clk),
+	/* clock derived from usbh clk */
+	CLKDEV_INIT(NULL, "usbh.0_clk", &usbh0_clk),
+	CLKDEV_INIT(NULL, "usbh.1_clk", &usbh1_clk),
 	/* clock derived from ahb clk */
-	{ .con_id = "apb_clk",		.clk = &apb_clk},
-	{ .dev_id = "i2c_designware.0",	.clk = &i2c_clk},
-	{ .dev_id = "dma",		.clk = &dma_clk},
-	{ .dev_id = "jpeg",		.clk = &jpeg_clk},
-	{ .dev_id = "gmac",		.clk = &gmac_clk},
-	{ .dev_id = "smi",		.clk = &smi_clk},
-	{ .dev_id = "c3",		.clk = &c3_clk},
+	CLKDEV_INIT(NULL, "apb_clk", &apb_clk),
+	CLKDEV_INIT("d0180000.i2c", NULL, &i2c_clk),
+	CLKDEV_INIT("fc400000.dma", NULL, &dma_clk),
+	CLKDEV_INIT("jpeg", NULL, &jpeg_clk),
+	CLKDEV_INIT("e0800000.eth", NULL, &gmac_clk),
+	CLKDEV_INIT("fc000000.flash", NULL, &smi_clk),
+	CLKDEV_INIT("c3", NULL, &c3_clk),
 	/* clock derived from apb clk */
-	{ .dev_id = "adc",		.clk = &adc_clk},
-	{ .dev_id = "ssp-pl022.0",	.clk = &ssp0_clk},
-	{ .dev_id = "gpio",		.clk = &gpio_clk},
+	CLKDEV_INIT("adc", NULL, &adc_clk),
+	CLKDEV_INIT("d0100000.spi", NULL, &ssp0_clk),
+	CLKDEV_INIT("fc980000.gpio", NULL, &gpio_clk),
 };
 
 /* array of all spear 300 clock lookups */
 #ifdef CONFIG_MACH_SPEAR300
 static struct clk_lookup spear300_clk_lookups[] = {
-	{ .dev_id = "clcd",		.clk = &clcd_clk},
-	{ .con_id = "fsmc",		.clk = &fsmc_clk},
-	{ .dev_id = "gpio1",		.clk = &gpio1_clk},
-	{ .dev_id = "keyboard",		.clk = &kbd_clk},
-	{ .dev_id = "sdhci",		.clk = &sdhci_clk},
+	CLKDEV_INIT("60000000.clcd", NULL, &clcd_clk),
+	CLKDEV_INIT("94000000.flash", NULL, &fsmc_clk),
+	CLKDEV_INIT("a9000000.gpio", NULL, &gpio1_clk),
+	CLKDEV_INIT("a0000000.kbd", NULL, &kbd_clk),
+	CLKDEV_INIT("70000000.sdhci", NULL, &sdhci_clk),
 };
+
+void __init spear300_clk_init(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(spear_clk_lookups); i++)
+		clk_register(&spear_clk_lookups[i]);
+
+	for (i = 0; i < ARRAY_SIZE(spear300_clk_lookups); i++)
+		clk_register(&spear300_clk_lookups[i]);
+
+	clk_init();
+}
 #endif
 
 /* array of all spear 310 clock lookups */
 #ifdef CONFIG_MACH_SPEAR310
 static struct clk_lookup spear310_clk_lookups[] = {
-	{ .con_id = "fsmc",		.clk = &fsmc_clk},
-	{ .con_id = "emi",		.clk = &emi_clk},
-	{ .dev_id = "uart1",		.clk = &uart1_clk},
-	{ .dev_id = "uart2",		.clk = &uart2_clk},
-	{ .dev_id = "uart3",		.clk = &uart3_clk},
-	{ .dev_id = "uart4",		.clk = &uart4_clk},
-	{ .dev_id = "uart5",		.clk = &uart5_clk},
+	CLKDEV_INIT("44000000.flash", NULL, &fsmc_clk),
+	CLKDEV_INIT(NULL, "emi", &emi_clk),
+	CLKDEV_INIT("b2000000.serial", NULL, &uart1_clk),
+	CLKDEV_INIT("b2080000.serial", NULL, &uart2_clk),
+	CLKDEV_INIT("b2100000.serial", NULL, &uart3_clk),
+	CLKDEV_INIT("b2180000.serial", NULL, &uart4_clk),
+	CLKDEV_INIT("b2200000.serial", NULL, &uart5_clk),
 };
+
+void __init spear310_clk_init(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(spear_clk_lookups); i++)
+		clk_register(&spear_clk_lookups[i]);
+
+	for (i = 0; i < ARRAY_SIZE(spear310_clk_lookups); i++)
+		clk_register(&spear310_clk_lookups[i]);
+
+	clk_init();
+}
 #endif
 
 /* array of all spear 320 clock lookups */
 #ifdef CONFIG_MACH_SPEAR320
 static struct clk_lookup spear320_clk_lookups[] = {
-	{ .dev_id = "clcd",		.clk = &clcd_clk},
-	{ .con_id = "fsmc",		.clk = &fsmc_clk},
-	{ .dev_id = "i2c_designware.1",	.clk = &i2c1_clk},
-	{ .con_id = "emi",		.clk = &emi_clk},
-	{ .dev_id = "pwm",		.clk = &pwm_clk},
-	{ .dev_id = "sdhci",		.clk = &sdhci_clk},
-	{ .dev_id = "c_can_platform.0",	.clk = &can0_clk},
-	{ .dev_id = "c_can_platform.1",	.clk = &can1_clk},
-	{ .dev_id = "ssp-pl022.1",	.clk = &ssp1_clk},
-	{ .dev_id = "ssp-pl022.2",	.clk = &ssp2_clk},
-	{ .dev_id = "uart1",		.clk = &uart1_clk},
-	{ .dev_id = "uart2",		.clk = &uart2_clk},
-};
-#endif
-
-void __init spear3xx_clk_init(void)
+	CLKDEV_INIT("90000000.clcd", NULL, &clcd_clk),
+	CLKDEV_INIT("4c000000.flash", NULL, &fsmc_clk),
+	CLKDEV_INIT("a7000000.i2c", NULL, &i2c1_clk),
+	CLKDEV_INIT(NULL, "emi", &emi_clk),
+	CLKDEV_INIT("pwm", NULL, &pwm_clk),
+	CLKDEV_INIT("70000000.sdhci", NULL, &sdhci_clk),
+	CLKDEV_INIT("c_can_platform.0", NULL, &can0_clk),
+	CLKDEV_INIT("c_can_platform.1", NULL, &can1_clk),
+	CLKDEV_INIT("a5000000.spi", NULL, &ssp1_clk),
+	CLKDEV_INIT("a6000000.spi", NULL, &ssp2_clk),
+	CLKDEV_INIT("a3000000.serial", NULL, &uart1_clk),
+	CLKDEV_INIT("a4000000.serial", NULL, &uart2_clk),
+};
+
+void __init spear320_clk_init(void)
 {
-	int i, cnt;
-	struct clk_lookup *lookups;
-
-	if (machine_is_spear300()) {
-		cnt = ARRAY_SIZE(spear300_clk_lookups);
-		lookups = spear300_clk_lookups;
-	} else if (machine_is_spear310()) {
-		cnt = ARRAY_SIZE(spear310_clk_lookups);
-		lookups = spear310_clk_lookups;
-	} else {
-		cnt = ARRAY_SIZE(spear320_clk_lookups);
-		lookups = spear320_clk_lookups;
-	}
+	int i;
 
 	for (i = 0; i < ARRAY_SIZE(spear_clk_lookups); i++)
 		clk_register(&spear_clk_lookups[i]);
 
-	for (i = 0; i < cnt; i++)
-		clk_register(&lookups[i]);
+	for (i = 0; i < ARRAY_SIZE(spear320_clk_lookups); i++)
+		clk_register(&spear320_clk_lookups[i]);
 
 	clk_init();
 }
+#endif

arch/arm/mach-spear3xx/include/mach/generic.h

@@ -14,12 +14,12 @@
 #ifndef __MACH_GENERIC_H
 #define __MACH_GENERIC_H
 
+#include <linux/amba/pl08x.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/amba/bus.h>
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
-#include <plat/padmux.h>
 
 /* spear3xx declarations */
 /*
@@ -31,171 +31,32 @@
 #define SPEAR_GPT0_CHAN1_IRQ	SPEAR3XX_IRQ_CPU_GPT1_2
 
 /* Add spear3xx family device structure declarations here */
-extern struct amba_device spear3xx_gpio_device;
-extern struct amba_device spear3xx_uart_device;
 extern struct sys_timer spear3xx_timer;
+extern struct pl022_ssp_controller pl022_plat_data;
+extern struct pl08x_platform_data pl080_plat_data;
 
 /* Add spear3xx family function declarations here */
-void __init spear3xx_clk_init(void);
 void __init spear_setup_timer(void);
 void __init spear3xx_map_io(void);
-void __init spear3xx_init_irq(void);
-void __init spear3xx_init(void);
+void __init spear3xx_dt_init_irq(void);
 
 void spear_restart(char, const char *);
 
-/* pad mux declarations */
-#define PMX_FIRDA_MASK		(1 << 14)
-#define PMX_I2C_MASK		(1 << 13)
-#define PMX_SSP_CS_MASK		(1 << 12)
-#define PMX_SSP_MASK		(1 << 11)
-#define PMX_MII_MASK		(1 << 10)
-#define PMX_GPIO_PIN0_MASK	(1 << 9)
-#define PMX_GPIO_PIN1_MASK	(1 << 8)
-#define PMX_GPIO_PIN2_MASK	(1 << 7)
-#define PMX_GPIO_PIN3_MASK	(1 << 6)
-#define PMX_GPIO_PIN4_MASK	(1 << 5)
-#define PMX_GPIO_PIN5_MASK	(1 << 4)
-#define PMX_UART0_MODEM_MASK	(1 << 3)
-#define PMX_UART0_MASK		(1 << 2)
-#define PMX_TIMER_3_4_MASK	(1 << 1)
-#define PMX_TIMER_1_2_MASK	(1 << 0)
-
-/* pad mux devices */
-extern struct pmx_dev spear3xx_pmx_firda;
-extern struct pmx_dev spear3xx_pmx_i2c;
-extern struct pmx_dev spear3xx_pmx_ssp_cs;
-extern struct pmx_dev spear3xx_pmx_ssp;
-extern struct pmx_dev spear3xx_pmx_mii;
-extern struct pmx_dev spear3xx_pmx_gpio_pin0;
-extern struct pmx_dev spear3xx_pmx_gpio_pin1;
-extern struct pmx_dev spear3xx_pmx_gpio_pin2;
-extern struct pmx_dev spear3xx_pmx_gpio_pin3;
-extern struct pmx_dev spear3xx_pmx_gpio_pin4;
-extern struct pmx_dev spear3xx_pmx_gpio_pin5;
-extern struct pmx_dev spear3xx_pmx_uart0_modem;
-extern struct pmx_dev spear3xx_pmx_uart0;
-extern struct pmx_dev spear3xx_pmx_timer_3_4;
-extern struct pmx_dev spear3xx_pmx_timer_1_2;
-
-#if defined(CONFIG_MACH_SPEAR310) || defined(CONFIG_MACH_SPEAR320)
-/* padmux plgpio devices */
-extern struct pmx_dev spear3xx_pmx_plgpio_0_1;
-extern struct pmx_dev spear3xx_pmx_plgpio_2_3;
-extern struct pmx_dev spear3xx_pmx_plgpio_4_5;
-extern struct pmx_dev spear3xx_pmx_plgpio_6_9;
-extern struct pmx_dev spear3xx_pmx_plgpio_10_27;
-extern struct pmx_dev spear3xx_pmx_plgpio_28;
-extern struct pmx_dev spear3xx_pmx_plgpio_29;
-extern struct pmx_dev spear3xx_pmx_plgpio_30;
-extern struct pmx_dev spear3xx_pmx_plgpio_31;
-extern struct pmx_dev spear3xx_pmx_plgpio_32;
-extern struct pmx_dev spear3xx_pmx_plgpio_33;
-extern struct pmx_dev spear3xx_pmx_plgpio_34_36;
-extern struct pmx_dev spear3xx_pmx_plgpio_37_42;
-extern struct pmx_dev spear3xx_pmx_plgpio_43_44_47_48;
-extern struct pmx_dev spear3xx_pmx_plgpio_45_46_49_50;
-#endif
-
 /* spear300 declarations */
 #ifdef CONFIG_MACH_SPEAR300
-/* Add spear300 machine device structure declarations here */
-extern struct amba_device spear300_gpio1_device;
-
-/* pad mux modes */
-extern struct pmx_mode spear300_nand_mode;
-extern struct pmx_mode spear300_nor_mode;
-extern struct pmx_mode spear300_photo_frame_mode;
-extern struct pmx_mode spear300_lend_ip_phone_mode;
-extern struct pmx_mode spear300_hend_ip_phone_mode;
-extern struct pmx_mode spear300_lend_wifi_phone_mode;
-extern struct pmx_mode spear300_hend_wifi_phone_mode;
-extern struct pmx_mode spear300_ata_pabx_wi2s_mode;
-extern struct pmx_mode spear300_ata_pabx_i2s_mode;
-extern struct pmx_mode spear300_caml_lcdw_mode;
-extern struct pmx_mode spear300_camu_lcd_mode;
-extern struct pmx_mode spear300_camu_wlcd_mode;
-extern struct pmx_mode spear300_caml_lcd_mode;
-
-/* pad mux devices */
-extern struct pmx_dev spear300_pmx_fsmc_2_chips;
-extern struct pmx_dev spear300_pmx_fsmc_4_chips;
-extern struct pmx_dev spear300_pmx_keyboard;
-extern struct pmx_dev spear300_pmx_clcd;
-extern struct pmx_dev spear300_pmx_telecom_gpio;
-extern struct pmx_dev spear300_pmx_telecom_tdm;
-extern struct pmx_dev spear300_pmx_telecom_spi_cs_i2c_clk;
-extern struct pmx_dev spear300_pmx_telecom_camera;
-extern struct pmx_dev spear300_pmx_telecom_dac;
-extern struct pmx_dev spear300_pmx_telecom_i2s;
-extern struct pmx_dev spear300_pmx_telecom_boot_pins;
-extern struct pmx_dev spear300_pmx_telecom_sdhci_4bit;
-extern struct pmx_dev spear300_pmx_telecom_sdhci_8bit;
-extern struct pmx_dev spear300_pmx_gpio1;
-
-/* Add spear300 machine function declarations here */
-void __init spear300_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
-		u8 pmx_dev_count);
+void __init spear300_clk_init(void);
 
 #endif /* CONFIG_MACH_SPEAR300 */
 
 /* spear310 declarations */
 #ifdef CONFIG_MACH_SPEAR310
-/* Add spear310 machine device structure declarations here */
-
-/* pad mux devices */
-extern struct pmx_dev spear310_pmx_emi_cs_0_1_4_5;
-extern struct pmx_dev spear310_pmx_emi_cs_2_3;
-extern struct pmx_dev spear310_pmx_uart1;
-extern struct pmx_dev spear310_pmx_uart2;
-extern struct pmx_dev spear310_pmx_uart3_4_5;
-extern struct pmx_dev spear310_pmx_fsmc;
-extern struct pmx_dev spear310_pmx_rs485_0_1;
-extern struct pmx_dev spear310_pmx_tdm0;
-
-/* Add spear310 machine function declarations here */
-void __init spear310_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
-		u8 pmx_dev_count);
+void __init spear310_clk_init(void);
 
 #endif /* CONFIG_MACH_SPEAR310 */
 
 /* spear320 declarations */
 #ifdef CONFIG_MACH_SPEAR320
-/* Add spear320 machine device structure declarations here */
-
-/* pad mux modes */
-extern struct pmx_mode spear320_auto_net_smii_mode;
-extern struct pmx_mode spear320_auto_net_mii_mode;
-extern struct pmx_mode spear320_auto_exp_mode;
-extern struct pmx_mode spear320_small_printers_mode;
-
-/* pad mux devices */
-extern struct pmx_dev spear320_pmx_clcd;
-extern struct pmx_dev spear320_pmx_emi;
-extern struct pmx_dev spear320_pmx_fsmc;
-extern struct pmx_dev spear320_pmx_spp;
-extern struct pmx_dev spear320_pmx_sdhci;
-extern struct pmx_dev spear320_pmx_i2s;
-extern struct pmx_dev spear320_pmx_uart1;
-extern struct pmx_dev spear320_pmx_uart1_modem;
-extern struct pmx_dev spear320_pmx_uart2;
-extern struct pmx_dev spear320_pmx_touchscreen;
-extern struct pmx_dev spear320_pmx_can;
-extern struct pmx_dev spear320_pmx_sdhci_led;
-extern struct pmx_dev spear320_pmx_pwm0;
-extern struct pmx_dev spear320_pmx_pwm1;
-extern struct pmx_dev spear320_pmx_pwm2;
-extern struct pmx_dev spear320_pmx_pwm3;
-extern struct pmx_dev spear320_pmx_ssp1;
-extern struct pmx_dev spear320_pmx_ssp2;
-extern struct pmx_dev spear320_pmx_mii1;
-extern struct pmx_dev spear320_pmx_smii0;
-extern struct pmx_dev spear320_pmx_smii1;
-extern struct pmx_dev spear320_pmx_i2c1;
-
-/* Add spear320 machine function declarations here */
-void __init spear320_init(struct pmx_mode *pmx_mode, struct pmx_dev **pmx_devs,
-		u8 pmx_dev_count);
+void __init spear320_clk_init(void);
 
 #endif /* CONFIG_MACH_SPEAR320 */
 

arch/arm/mach-spear3xx/include/mach/hardware.h

@@ -17,7 +17,4 @@
 #include <plat/hardware.h>
 #include <mach/spear.h>
 
-/* Vitual to physical translation of statically mapped space */
-#define IO_ADDRESS(x)		(x | 0xF0000000)
-
 #endif /* __MACH_HARDWARE_H */

arch/arm/mach-spear3xx/include/mach/spear.h

@@ -25,8 +25,9 @@
 
 /* ICM1 - Low speed connection */
 #define SPEAR3XX_ICM1_2_BASE		UL(0xD0000000)
+#define VA_SPEAR3XX_ICM1_2_BASE		UL(0xFD000000)
 #define SPEAR3XX_ICM1_UART_BASE		UL(0xD0000000)
-#define VA_SPEAR3XX_ICM1_UART_BASE	IO_ADDRESS(SPEAR3XX_ICM1_UART_BASE)
+#define VA_SPEAR3XX_ICM1_UART_BASE	(VA_SPEAR3XX_ICM1_2_BASE | SPEAR3XX_ICM1_UART_BASE)
 #define SPEAR3XX_ICM1_ADC_BASE		UL(0xD0080000)
 #define SPEAR3XX_ICM1_SSP_BASE		UL(0xD0100000)
 #define SPEAR3XX_ICM1_I2C_BASE		UL(0xD0180000)
@@ -53,11 +54,11 @@
 #define SPEAR3XX_ICM3_ML1_2_BASE	UL(0xF0000000)
 #define SPEAR3XX_ML1_TMR_BASE		UL(0xF0000000)
 #define SPEAR3XX_ML1_VIC_BASE		UL(0xF1100000)
-#define VA_SPEAR3XX_ML1_VIC_BASE	IO_ADDRESS(SPEAR3XX_ML1_VIC_BASE)
 
 /* ICM3 - Basic Subsystem */
 #define SPEAR3XX_ICM3_SMEM_BASE		UL(0xF8000000)
 #define SPEAR3XX_ICM3_SMI_CTRL_BASE	UL(0xFC000000)
+#define VA_SPEAR3XX_ICM3_SMI_CTRL_BASE	UL(0xFC000000)
 #define SPEAR3XX_ICM3_DMA_BASE		UL(0xFC400000)
 #define SPEAR3XX_ICM3_SDRAM_CTRL_BASE	UL(0xFC600000)
 #define SPEAR3XX_ICM3_TMR0_BASE		UL(0xFC800000)
@@ -65,9 +66,9 @@
 #define SPEAR3XX_ICM3_RTC_BASE		UL(0xFC900000)
 #define SPEAR3XX_ICM3_GPIO_BASE		UL(0xFC980000)
 #define SPEAR3XX_ICM3_SYS_CTRL_BASE	UL(0xFCA00000)
-#define VA_SPEAR3XX_ICM3_SYS_CTRL_BASE	IO_ADDRESS(SPEAR3XX_ICM3_SYS_CTRL_BASE)
+#define VA_SPEAR3XX_ICM3_SYS_CTRL_BASE	(VA_SPEAR3XX_ICM3_SMI_CTRL_BASE | SPEAR3XX_ICM3_SYS_CTRL_BASE)
 #define SPEAR3XX_ICM3_MISC_REG_BASE	UL(0xFCA80000)
-#define VA_SPEAR3XX_ICM3_MISC_REG_BASE	IO_ADDRESS(SPEAR3XX_ICM3_MISC_REG_BASE)
+#define VA_SPEAR3XX_ICM3_MISC_REG_BASE	(VA_SPEAR3XX_ICM3_SMI_CTRL_BASE | SPEAR3XX_ICM3_MISC_REG_BASE)
 #define SPEAR3XX_ICM3_TMR1_BASE		UL(0xFCB00000)
 
 /* Debug uart for linux, will be used for debug and uncompress messages */

arch/arm/mach-spear3xx/spear300_evb.c

-/*
- * arch/arm/mach-spear3xx/spear300_evb.c
- *
- * SPEAr300 evaluation board source file
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <asm/hardware/vic.h>
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <mach/generic.h>
-#include <mach/hardware.h>
-
-/* padmux devices to enable */
-static struct pmx_dev *pmx_devs[] = {
-	/* spear3xx specific devices */
-	&spear3xx_pmx_i2c,
-	&spear3xx_pmx_ssp_cs,
-	&spear3xx_pmx_ssp,
-	&spear3xx_pmx_mii,
-	&spear3xx_pmx_uart0,
-
-	/* spear300 specific devices */
-	&spear300_pmx_fsmc_2_chips,
-	&spear300_pmx_clcd,
-	&spear300_pmx_telecom_sdhci_4bit,
-	&spear300_pmx_gpio1,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
-	/* spear3xx specific devices */
-	&spear3xx_gpio_device,
-	&spear3xx_uart_device,
-
-	/* spear300 specific devices */
-	&spear300_gpio1_device,
-};
-
-static struct platform_device *plat_devs[] __initdata = {
-	/* spear3xx specific devices */
-
-	/* spear300 specific devices */
-};
-
-static void __init spear300_evb_init(void)
-{
-	unsigned int i;
-
-	/* call spear300 machine init function */
-	spear300_init(&spear300_photo_frame_mode, pmx_devs,
-			ARRAY_SIZE(pmx_devs));
-
-	/* Add Platform Devices */
-	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
-
-	/* Add Amba Devices */
-	for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
-		amba_device_register(amba_devs[i], &iomem_resource);
-}
-
-MACHINE_START(SPEAR300, "ST-SPEAR300-EVB")
-	.atag_offset	=	0x100,
-	.map_io		=	spear3xx_map_io,
-	.init_irq	=	spear3xx_init_irq,
-	.handle_irq	=	vic_handle_irq,
-	.timer		=	&spear3xx_timer,
-	.init_machine	=	spear300_evb_init,
-	.restart	=	spear_restart,
-MACHINE_END

arch/arm/mach-spear3xx/spear310_evb.c

-/*
- * arch/arm/mach-spear3xx/spear310_evb.c
- *
- * SPEAr310 evaluation board source file
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <asm/hardware/vic.h>
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <mach/generic.h>
-#include <mach/hardware.h>
-
-/* padmux devices to enable */
-static struct pmx_dev *pmx_devs[] = {
-	/* spear3xx specific devices */
-	&spear3xx_pmx_i2c,
-	&spear3xx_pmx_ssp,
-	&spear3xx_pmx_gpio_pin0,
-	&spear3xx_pmx_gpio_pin1,
-	&spear3xx_pmx_gpio_pin2,
-	&spear3xx_pmx_gpio_pin3,
-	&spear3xx_pmx_gpio_pin4,
-	&spear3xx_pmx_gpio_pin5,
-	&spear3xx_pmx_uart0,
-
-	/* spear310 specific devices */
-	&spear310_pmx_emi_cs_0_1_4_5,
-	&spear310_pmx_emi_cs_2_3,
-	&spear310_pmx_uart1,
-	&spear310_pmx_uart2,
-	&spear310_pmx_uart3_4_5,
-	&spear310_pmx_fsmc,
-	&spear310_pmx_rs485_0_1,
-	&spear310_pmx_tdm0,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
-	/* spear3xx specific devices */
-	&spear3xx_gpio_device,
-	&spear3xx_uart_device,
-
-	/* spear310 specific devices */
-};
-
-static struct platform_device *plat_devs[] __initdata = {
-	/* spear3xx specific devices */
-
-	/* spear310 specific devices */
-};
-
-static void __init spear310_evb_init(void)
-{
-	unsigned int i;
-
-	/* call spear310 machine init function */
-	spear310_init(NULL, pmx_devs, ARRAY_SIZE(pmx_devs));
-
-	/* Add Platform Devices */
-	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
-
-	/* Add Amba Devices */
-	for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
-		amba_device_register(amba_devs[i], &iomem_resource);
-}
-
-MACHINE_START(SPEAR310, "ST-SPEAR310-EVB")
-	.atag_offset	=	0x100,
-	.map_io		=	spear3xx_map_io,
-	.init_irq	=	spear3xx_init_irq,
-	.handle_irq	=	vic_handle_irq,
-	.timer		=	&spear3xx_timer,
-	.init_machine	=	spear310_evb_init,
-	.restart	=	spear_restart,
-MACHINE_END

arch/arm/mach-spear3xx/spear320_evb.c

-/*
- * arch/arm/mach-spear3xx/spear320_evb.c
- *
- * SPEAr320 evaluation board source file
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <asm/hardware/vic.h>
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-#include <mach/generic.h>
-#include <mach/hardware.h>
-
-/* padmux devices to enable */
-static struct pmx_dev *pmx_devs[] = {
-	/* spear3xx specific devices */
-	&spear3xx_pmx_i2c,
-	&spear3xx_pmx_ssp,
-	&spear3xx_pmx_mii,
-	&spear3xx_pmx_uart0,
-
-	/* spear320 specific devices */
-	&spear320_pmx_fsmc,
-	&spear320_pmx_sdhci,
-	&spear320_pmx_i2s,
-	&spear320_pmx_uart1,
-	&spear320_pmx_uart2,
-	&spear320_pmx_can,
-	&spear320_pmx_pwm0,
-	&spear320_pmx_pwm1,
-	&spear320_pmx_pwm2,
-	&spear320_pmx_mii1,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
-	/* spear3xx specific devices */
-	&spear3xx_gpio_device,
-	&spear3xx_uart_device,
-
-	/* spear320 specific devices */
-};
-
-static struct platform_device *plat_devs[] __initdata = {
-	/* spear3xx specific devices */
-
-	/* spear320 specific devices */
-};
-
-static void __init spear320_evb_init(void)
-{
-	unsigned int i;
-
-	/* call spear320 machine init function */
-	spear320_init(&spear320_auto_net_mii_mode, pmx_devs,
-			ARRAY_SIZE(pmx_devs));
-
-	/* Add Platform Devices */
-	platform_add_devices(plat_devs, ARRAY_SIZE(plat_devs));
-
-	/* Add Amba Devices */
-	for (i = 0; i < ARRAY_SIZE(amba_devs); i++)
-		amba_device_register(amba_devs[i], &iomem_resource);
-}
-
-MACHINE_START(SPEAR320, "ST-SPEAR320-EVB")
-	.atag_offset	=	0x100,
-	.map_io		=	spear3xx_map_io,
-	.init_irq	=	spear3xx_init_irq,
-	.handle_irq	=	vic_handle_irq,
-	.timer		=	&spear3xx_timer,
-	.init_machine	=	spear320_evb_init,
-	.restart	=	spear_restart,
-MACHINE_END

arch/arm/mach-spear6xx/Makefile.boot

 zreladdr-y	+= 0x00008000
 params_phys-y	:= 0x00000100
 initrd_phys-y	:= 0x00800000
+
+dtb-$(CONFIG_BOARD_SPEAR600_DT)	+= spear600-evb.dtb

arch/arm/mach-spear6xx/clock.c

@@ -623,53 +623,53 @@ static struct clk dummy_apb_pclk;
 
 /* array of all spear 6xx clock lookups */
 static struct clk_lookup spear_clk_lookups[] = {
-	{ .con_id = "apb_pclk",		.clk = &dummy_apb_pclk},
+	CLKDEV_INIT(NULL, "apb_pclk", &dummy_apb_pclk),
 	/* root clks */
-	{ .con_id = "osc_32k_clk",	.clk = &osc_32k_clk},
-	{ .con_id = "osc_30m_clk",	.clk = &osc_30m_clk},
+	CLKDEV_INIT(NULL, "osc_32k_clk", &osc_32k_clk),
+	CLKDEV_INIT(NULL, "osc_30m_clk", &osc_30m_clk),
 	/* clock derived from 32 KHz os		 clk */
-	{ .dev_id = "rtc-spear",	.clk = &rtc_clk},
+	CLKDEV_INIT("rtc-spear", NULL, &rtc_clk),
 	/* clock derived from 30 MHz os		 clk */
-	{ .con_id = "pll1_clk",		.clk = &pll1_clk},
-	{ .con_id = "pll3_48m_clk",	.clk = &pll3_48m_clk},
-	{ .dev_id = "wdt",		.clk = &wdt_clk},
+	CLKDEV_INIT(NULL, "pll1_clk", &pll1_clk),
+	CLKDEV_INIT(NULL, "pll3_48m_clk", &pll3_48m_clk),
+	CLKDEV_INIT("wdt", NULL, &wdt_clk),
 	/* clock derived from pll1 clk */
-	{ .con_id = "cpu_clk",		.clk = &cpu_clk},
-	{ .con_id = "ahb_clk",		.clk = &ahb_clk},
-	{ .con_id = "uart_synth_clk",	.clk = &uart_synth_clk},
-	{ .con_id = "firda_synth_clk",	.clk = &firda_synth_clk},
-	{ .con_id = "clcd_synth_clk",	.clk = &clcd_synth_clk},
-	{ .con_id = "gpt0_synth_clk",	.clk = &gpt0_synth_clk},
-	{ .con_id = "gpt2_synth_clk",	.clk = &gpt2_synth_clk},
-	{ .con_id = "gpt3_synth_clk",	.clk = &gpt3_synth_clk},
-	{ .dev_id = "d0000000.serial",	.clk = &uart0_clk},
-	{ .dev_id = "d0080000.serial",	.clk = &uart1_clk},
-	{ .dev_id = "firda",		.clk = &firda_clk},
-	{ .dev_id = "clcd",		.clk = &clcd_clk},
-	{ .dev_id = "gpt0",		.clk = &gpt0_clk},
-	{ .dev_id = "gpt1",		.clk = &gpt1_clk},
-	{ .dev_id = "gpt2",		.clk = &gpt2_clk},
-	{ .dev_id = "gpt3",		.clk = &gpt3_clk},
+	CLKDEV_INIT(NULL, "cpu_clk", &cpu_clk),
+	CLKDEV_INIT(NULL, "ahb_clk", &ahb_clk),
+	CLKDEV_INIT(NULL, "uart_synth_clk", &uart_synth_clk),
+	CLKDEV_INIT(NULL, "firda_synth_clk", &firda_synth_clk),
+	CLKDEV_INIT(NULL, "clcd_synth_clk", &clcd_synth_clk),
+	CLKDEV_INIT(NULL, "gpt0_synth_clk", &gpt0_synth_clk),
+	CLKDEV_INIT(NULL, "gpt2_synth_clk", &gpt2_synth_clk),
+	CLKDEV_INIT(NULL, "gpt3_synth_clk", &gpt3_synth_clk),
+	CLKDEV_INIT("d0000000.serial", NULL, &uart0_clk),
+	CLKDEV_INIT("d0080000.serial", NULL, &uart1_clk),
+	CLKDEV_INIT("firda", NULL, &firda_clk),
+	CLKDEV_INIT("clcd", NULL, &clcd_clk),
+	CLKDEV_INIT("gpt0", NULL, &gpt0_clk),
+	CLKDEV_INIT("gpt1", NULL, &gpt1_clk),
+	CLKDEV_INIT("gpt2", NULL, &gpt2_clk),
+	CLKDEV_INIT("gpt3", NULL, &gpt3_clk),
 	/* clock derived from pll3 clk */
-	{ .dev_id = "designware_udc",	.clk = &usbd_clk},
-	{ .con_id = "usbh.0_clk",	.clk = &usbh0_clk},
-	{ .con_id = "usbh.1_clk",	.clk = &usbh1_clk},
+	CLKDEV_INIT("designware_udc", NULL, &usbd_clk),
+	CLKDEV_INIT(NULL, "usbh.0_clk", &usbh0_clk),
+	CLKDEV_INIT(NULL, "usbh.1_clk", &usbh1_clk),
 	/* clock derived from ahb clk */
-	{ .con_id = "apb_clk",		.clk = &apb_clk},
-	{ .dev_id = "d0200000.i2c",	.clk = &i2c_clk},
-	{ .dev_id = "dma",		.clk = &dma_clk},
-	{ .dev_id = "jpeg",		.clk = &jpeg_clk},
-	{ .dev_id = "gmac",		.clk = &gmac_clk},
-	{ .dev_id = "smi",		.clk = &smi_clk},
-	{ .dev_id = "fsmc-nand",	.clk = &fsmc_clk},
+	CLKDEV_INIT(NULL, "apb_clk", &apb_clk),
+	CLKDEV_INIT("d0200000.i2c", NULL, &i2c_clk),
+	CLKDEV_INIT("fc400000.dma", NULL, &dma_clk),
+	CLKDEV_INIT("jpeg", NULL, &jpeg_clk),
+	CLKDEV_INIT("gmac", NULL, &gmac_clk),
+	CLKDEV_INIT("fc000000.flash", NULL, &smi_clk),
+	CLKDEV_INIT("d1800000.flash", NULL, &fsmc_clk),
 	/* clock derived from apb clk */
-	{ .dev_id = "adc",		.clk = &adc_clk},
-	{ .dev_id = "ssp-pl022.0",	.clk = &ssp0_clk},
-	{ .dev_id = "ssp-pl022.1",	.clk = &ssp1_clk},
-	{ .dev_id = "ssp-pl022.2",	.clk = &ssp2_clk},
-	{ .dev_id = "f0100000.gpio",	.clk = &gpio0_clk},
-	{ .dev_id = "fc980000.gpio",	.clk = &gpio1_clk},
-	{ .dev_id = "d8100000.gpio",	.clk = &gpio2_clk},
+	CLKDEV_INIT("adc", NULL, &adc_clk),
+	CLKDEV_INIT("ssp-pl022.0", NULL, &ssp0_clk),
+	CLKDEV_INIT("ssp-pl022.1", NULL, &ssp1_clk),
+	CLKDEV_INIT("ssp-pl022.2", NULL, &ssp2_clk),
+	CLKDEV_INIT("f0100000.gpio", NULL, &gpio0_clk),
+	CLKDEV_INIT("fc980000.gpio", NULL, &gpio1_clk),
+	CLKDEV_INIT("d8100000.gpio", NULL, &gpio2_clk),
 };
 
 void __init spear6xx_clk_init(void)

arch/arm/plat-spear/Kconfig

@@ -9,9 +9,11 @@ choice
 	default ARCH_SPEAR3XX
 
 config ARCH_SPEAR3XX
-	bool "SPEAr3XX"
+	bool "ST SPEAr3xx with Device Tree"
 	select ARM_VIC
 	select CPU_ARM926T
+	select USE_OF
+	select PINCTRL
 	help
 	  Supports for ARM's SPEAR3XX family
 

arch/arm/plat-spear/Makefile

@@ -3,6 +3,6 @@
 #
 
 # Common support
-obj-y	:= clock.o restart.o time.o
+obj-y	:= clock.o restart.o time.o pl080.o
 
-obj-$(CONFIG_ARCH_SPEAR3XX)	+= shirq.o padmux.o
+obj-$(CONFIG_ARCH_SPEAR3XX)	+= shirq.o

arch/arm/plat-spear/include/plat/padmux.h

-/*
- * arch/arm/plat-spear/include/plat/padmux.h
- *
- * SPEAr platform specific gpio pads muxing file
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __PLAT_PADMUX_H
-#define __PLAT_PADMUX_H
-
-#include <linux/types.h>
-
-/*
- * struct pmx_reg: configuration structure for mode reg and mux reg
- *
- * offset: offset of mode reg
- * mask: mask of mode reg
- */
-struct pmx_reg {
-	u32 offset;
-	u32 mask;
-};
-
-/*
- * struct pmx_dev_mode: configuration structure every group of modes of a device
- *
- * ids: all modes for this configuration
- * mask: mask for supported mode
- */
-struct pmx_dev_mode {
-	u32 ids;
-	u32 mask;
-};
-
-/*
- * struct pmx_mode: mode definition structure
- *
- * name: mode name
- * mask: mode mask
- */
-struct pmx_mode {
-	char *name;
-	u32 id;
-	u32 mask;
-};
-
-/*
- * struct pmx_dev: device definition structure
- *
- * name: device name
- * modes: device configuration array for different modes supported
- * mode_count: size of modes array
- * is_active: is peripheral active/enabled
- * enb_on_reset: if 1, mask bits to be cleared in reg otherwise to be set in reg
- */
-struct pmx_dev {
-	char *name;
-	struct pmx_dev_mode *modes;
-	u8 mode_count;
-	bool is_active;
-	bool enb_on_reset;
-};
-
-/*
- * struct pmx_driver: driver definition structure
- *
- * mode: mode to be set
- * devs: array of pointer to pmx devices
- * devs_count: ARRAY_SIZE of devs
- * base: base address of soc config registers
- * mode_reg: structure of mode config register
- * mux_reg: structure of device mux config register
- */
-struct pmx_driver {
-	struct pmx_mode *mode;
-	struct pmx_dev **devs;
-	u8 devs_count;
-	u32 *base;
-	struct pmx_reg mode_reg;
-	struct pmx_reg mux_reg;
-};
-
-/* pmx functions */
-int pmx_register(struct pmx_driver *driver);
-
-#endif /* __PLAT_PADMUX_H */

arch/arm/plat-spear/include/plat/pl080.h

+/*
+ * arch/arm/plat-spear/include/plat/pl080.h
+ *
+ * DMAC pl080 definitions for SPEAr platform
+ *
+ * Copyright (C) 2012 ST Microelectronics
+ * Viresh Kumar <viresh.kumar@st.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __PLAT_PL080_H
+#define __PLAT_PL080_H
+
+struct pl08x_dma_chan;
+int pl080_get_signal(struct pl08x_dma_chan *ch);
+void pl080_put_signal(struct pl08x_dma_chan *ch);
+
+#endif /* __PLAT_PL080_H */

arch/arm/plat-spear/padmux.c

-/*
- * arch/arm/plat-spear/include/plat/padmux.c
- *
- * SPEAr platform specific gpio pads muxing source file
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/slab.h>
-#include <plat/padmux.h>
-
-/*
- * struct pmx: pmx definition structure
- *
- * base: base address of configuration registers
- * mode_reg: mode configurations
- * mux_reg: muxing configurations
- * active_mode: pointer to current active mode
- */
-struct pmx {
-	u32 base;
-	struct pmx_reg mode_reg;
-	struct pmx_reg mux_reg;
-	struct pmx_mode *active_mode;
-};
-
-static struct pmx *pmx;
-
-/**
- * pmx_mode_set - Enables an multiplexing mode
- * @mode - pointer to pmx mode
- *
- * It will set mode of operation in hardware.
- * Returns -ve on Err otherwise 0
- */
-static int pmx_mode_set(struct pmx_mode *mode)
-{
-	u32 val;
-
-	if (!mode->name)
-		return -EFAULT;
-
-	pmx->active_mode = mode;
-
-	val = readl(pmx->base + pmx->mode_reg.offset);
-	val &= ~pmx->mode_reg.mask;
-	val |= mode->mask & pmx->mode_reg.mask;
-	writel(val, pmx->base + pmx->mode_reg.offset);
-
-	return 0;
-}
-
-/**
- * pmx_devs_enable - Enables list of devices
- * @devs - pointer to pmx device array
- * @count - number of devices to enable
- *
- * It will enable pads for all required peripherals once and only once.
- * If peripheral is not supported by current mode then request is rejected.
- * Conflicts between peripherals are not handled and peripherals will be
- * enabled in the order they are present in pmx_dev array.
- * In case of conflicts last peripheral enabled will be present.
- * Returns -ve on Err otherwise 0
- */
-static int pmx_devs_enable(struct pmx_dev **devs, u8 count)
-{
-	u32 val, i, mask;
-
-	if (!count)
-		return -EINVAL;
-
-	val = readl(pmx->base + pmx->mux_reg.offset);
-	for (i = 0; i < count; i++) {
-		u8 j = 0;
-
-		if (!devs[i]->name || !devs[i]->modes) {
-			printk(KERN_ERR "padmux: dev name or modes is null\n");
-			continue;
-		}
-		/* check if peripheral exists in active mode */
-		if (pmx->active_mode) {
-			bool found = false;
-			for (j = 0; j < devs[i]->mode_count; j++) {
-				if (devs[i]->modes[j].ids &
-						pmx->active_mode->id) {
-					found = true;
-					break;
-				}
-			}
-			if (found == false) {
-				printk(KERN_ERR "%s device not available in %s"\
-						"mode\n", devs[i]->name,
-						pmx->active_mode->name);
-				continue;
-			}
-		}
-
-		/* enable peripheral */
-		mask = devs[i]->modes[j].mask & pmx->mux_reg.mask;
-		if (devs[i]->enb_on_reset)
-			val &= ~mask;
-		else
-			val |= mask;
-
-		devs[i]->is_active = true;
-	}
-	writel(val, pmx->base + pmx->mux_reg.offset);
-	kfree(pmx);
-
-	/* this will ensure that multiplexing can't be changed now */
-	pmx = (struct pmx *)-1;
-
-	return 0;
-}
-
-/**
- * pmx_register - registers a platform requesting pad mux feature
- * @driver - pointer to driver structure containing driver specific parameters
- *
- * Also this must be called only once. This will allocate memory for pmx
- * structure, will call pmx_mode_set, will call pmx_devs_enable.
- * Returns -ve on Err otherwise 0
- */
-int pmx_register(struct pmx_driver *driver)
-{
-	int ret = 0;
-
-	if (pmx)
-		return -EPERM;
-	if (!driver->base || !driver->devs)
-		return -EFAULT;
-
-	pmx = kzalloc(sizeof(*pmx), GFP_KERNEL);
-	if (!pmx)
-		return -ENOMEM;
-
-	pmx->base = (u32)driver->base;
-	pmx->mode_reg.offset = driver->mode_reg.offset;
-	pmx->mode_reg.mask = driver->mode_reg.mask;
-	pmx->mux_reg.offset = driver->mux_reg.offset;
-	pmx->mux_reg.mask = driver->mux_reg.mask;
-
-	/* choose mode to enable */
-	if (driver->mode) {
-		ret = pmx_mode_set(driver->mode);
-		if (ret)
-			goto pmx_fail;
-	}
-	ret = pmx_devs_enable(driver->devs, driver->devs_count);
-	if (ret)
-		goto pmx_fail;
-
-	return 0;
-
-pmx_fail:
-	return ret;
-}

arch/arm/plat-spear/pl080.c

+/*
+ * arch/arm/plat-spear/pl080.c
+ *
+ * DMAC pl080 definitions for SPEAr platform
+ *
+ * Copyright (C) 2012 ST Microelectronics
+ * Viresh Kumar <viresh.kumar@st.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/amba/pl08x.h>
+#include <linux/amba/bus.h>
+#include <linux/bug.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/spinlock_types.h>
+#include <mach/misc_regs.h>
+
+static spinlock_t lock = __SPIN_LOCK_UNLOCKED(x);
+
+struct {
+	unsigned char busy;
+	unsigned char val;
+} signals[16] = {{0, 0}, };
+
+int pl080_get_signal(struct pl08x_dma_chan *ch)
+{
+	const struct pl08x_channel_data *cd = ch->cd;
+	unsigned int signal = cd->min_signal, val;
+	unsigned long flags;
+
+	spin_lock_irqsave(&lock, flags);
+
+	/* Return if signal is already acquired by somebody else */
+	if (signals[signal].busy &&
+			(signals[signal].val != cd->muxval)) {
+		spin_unlock_irqrestore(&lock, flags);
+		return -EBUSY;
+	}
+
+	/* If acquiring for the first time, configure it */
+	if (!signals[signal].busy) {
+		val = readl(DMA_CHN_CFG);
+
+		/*
+		 * Each request line has two bits in DMA_CHN_CFG register. To
+		 * goto the bits of current request line, do left shift of
+		 * value by 2 * signal number.
+		 */
+		val &= ~(0x3 << (signal * 2));
+		val |= cd->muxval << (signal * 2);
+		writel(val, DMA_CHN_CFG);
+	}
+
+	signals[signal].busy++;
+	signals[signal].val = cd->muxval;
+	spin_unlock_irqrestore(&lock, flags);
+
+	return signal;
+}
+
+void pl080_put_signal(struct pl08x_dma_chan *ch)
+{
+	const struct pl08x_channel_data *cd = ch->cd;
+	unsigned long flags;
+
+	spin_lock_irqsave(&lock, flags);
+
+	/* if signal is not used */
+	if (!signals[cd->min_signal].busy)
+		BUG();
+
+	signals[cd->min_signal].busy--;
+
+	spin_unlock_irqrestore(&lock, flags);
+}

drivers/pinctrl/Kconfig

@@ -84,6 +84,8 @@ config PINCTRL_COH901
 	  COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
 	  ports of 8 GPIO pins each.
 
+source "drivers/pinctrl/spear/Kconfig"
+
 endmenu
 
 endif