ARM: dts: imx6qdl-vicut1/vicutgo: Add backlight_led node

backlight_led is the dimmable backlight for the rubber border on the case. It
is also used to highlight the power- and some other buttons.

MX6QDL_PAD_SD4_DAT1__PWM3_OUT is also assigned as output for pwm3. Since
we need pwm3 for the backlight, we're forced to disable user space hardware
revision detection. The bootloader will have to supply this information
(i.e. through device tree).
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arch/arm/boot/dts/imx6dl-victgo.dts

@@ -33,6 +33,15 @@ backlight_lcd: backlight {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight_led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -392,8 +401,8 @@ &gpio1 {
 &gpio2 {
 	gpio-line-names =
 		"", "", "", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
 		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
 		"POWER_LED", "", "", "", "", "", "", "";
 };
@@ -778,17 +787,6 @@ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 is shared with PWM3 */
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0

arch/arm/boot/dts/imx6qdl-vicut1.dtsi

@@ -28,6 +28,15 @@ backlight_lcd: backlight {
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight_led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -448,6 +457,12 @@ &pwm1 {
 	status = "okay";
 };
 
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
 &ssi1 {
 	#sound-dai-cells = <0>;
 	fsl,mode = "ac97-slave";
@@ -669,18 +684,6 @@ MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 */
-			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09			0x1b0b0
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
@@ -738,6 +741,12 @@ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
 		>;
 	};
 
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
+		>;
+	};
+
 	/* YaCO AUX Uart */
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <