Commit 9bce4b27 authored by Andrew Jeffery's avatar Andrew Jeffery Committed by David S. Miller

net: ftgmac100: Ungate RCLK for RMII on ASPEED MACs

The 50MHz RCLK has to be enabled before the RMII interface will function.
Signed-off-by: default avatarAndrew Jeffery <andrew@aj.id.au>
Reviewed-by: default avatarJoel Stanley <joel@jms.id.au>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 042b8675
......@@ -90,6 +90,9 @@ struct ftgmac100 {
struct mii_bus *mii_bus;
struct clk *clk;
/* AST2500/AST2600 RMII ref clock gate */
struct clk *rclk;
/* Link management */
int cur_speed;
int cur_duplex;
......@@ -1718,20 +1721,41 @@ static void ftgmac100_ncsi_handler(struct ncsi_dev *nd)
nd->link_up ? "up" : "down");
}
static void ftgmac100_setup_clk(struct ftgmac100 *priv)
static int ftgmac100_setup_clk(struct ftgmac100 *priv)
{
priv->clk = devm_clk_get(priv->dev, NULL);
if (IS_ERR(priv->clk))
return;
struct clk *clk;
int rc;
clk_prepare_enable(priv->clk);
clk = devm_clk_get(priv->dev, NULL /* MACCLK */);
if (IS_ERR(clk))
return PTR_ERR(clk);
priv->clk = clk;
rc = clk_prepare_enable(priv->clk);
if (rc)
return rc;
/* Aspeed specifies a 100MHz clock is required for up to
* 1000Mbit link speeds. As NCSI is limited to 100Mbit, 25MHz
* is sufficient
*/
clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
FTGMAC_100MHZ);
rc = clk_set_rate(priv->clk, priv->use_ncsi ? FTGMAC_25MHZ :
FTGMAC_100MHZ);
if (rc)
goto cleanup_clk;
/* RCLK is for RMII, typically used for NCSI. Optional because its not
* necessary if it's the AST2400 MAC, or the MAC is configured for
* RGMII, or the controller is not an ASPEED-based controller.
*/
priv->rclk = devm_clk_get_optional(priv->dev, "RCLK");
rc = clk_prepare_enable(priv->rclk);
if (!rc)
return 0;
cleanup_clk:
clk_disable_unprepare(priv->clk);
return rc;
}
static int ftgmac100_probe(struct platform_device *pdev)
......@@ -1853,8 +1877,11 @@ static int ftgmac100_probe(struct platform_device *pdev)
goto err_setup_mdio;
}
if (priv->is_aspeed)
ftgmac100_setup_clk(priv);
if (priv->is_aspeed) {
err = ftgmac100_setup_clk(priv);
if (err)
goto err_ncsi_dev;
}
/* Default ring sizes */
priv->rx_q_entries = priv->new_rx_q_entries = DEF_RX_QUEUE_ENTRIES;
......@@ -1886,8 +1913,10 @@ static int ftgmac100_probe(struct platform_device *pdev)
return 0;
err_ncsi_dev:
err_register_netdev:
clk_disable_unprepare(priv->rclk);
clk_disable_unprepare(priv->clk);
err_ncsi_dev:
ftgmac100_destroy_mdio(netdev);
err_setup_mdio:
iounmap(priv->base);
......@@ -1909,6 +1938,7 @@ static int ftgmac100_remove(struct platform_device *pdev)
unregister_netdev(netdev);
clk_disable_unprepare(priv->rclk);
clk_disable_unprepare(priv->clk);
/* There's a small chance the reset task will have been re-queued,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment