Commit 9bf206a9 authored by Fabio Estevam's avatar Fabio Estevam Committed by Shawn Guo

ARM: dts: imx51-babbage: Add USB Host1 support

Signed-off by: Dave Ebright <dave.ebright@parsons.com>
Signed-off-by: default avatarFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: default avatarShawn Guo <shawn.guo@freescale.com>
parent ebc37465
...@@ -129,6 +129,35 @@ clk_26M: codec_clock { ...@@ -129,6 +129,35 @@ clk_26M: codec_clock {
gpios = <&gpio4 26 GPIO_ACTIVE_LOW>; gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
}; };
}; };
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_usb_vbus: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "usb_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio2 5 0>;
enable-active-high;
};
};
usbphy {
#address-cells = <1>;
#size-cells = <0>;
compatible = "simple-bus";
usbh1phy: usbh1phy@0 {
compatible = "usb-nop-xceiv";
reg = <0>;
clocks = <&clks 0>;
clock-names = "main_clk";
};
};
}; };
&esdhc1 { &esdhc1 {
...@@ -479,6 +508,23 @@ MX51_PAD_EIM_D27__UART3_RTS 0x1c5 ...@@ -479,6 +508,23 @@ MX51_PAD_EIM_D27__UART3_RTS 0x1c5
MX51_PAD_EIM_D24__UART3_CTS 0x1c5 MX51_PAD_EIM_D24__UART3_CTS 0x1c5
>; >;
}; };
pinctrl_usbh1: usbh1grp {
fsl,pins = <
MX51_PAD_USBH1_CLK__USBH1_CLK 0x80000000
MX51_PAD_USBH1_DIR__USBH1_DIR 0x80000000
MX51_PAD_USBH1_NXT__USBH1_NXT 0x80000000
MX51_PAD_USBH1_DATA0__USBH1_DATA0 0x80000000
MX51_PAD_USBH1_DATA1__USBH1_DATA1 0x80000000
MX51_PAD_USBH1_DATA2__USBH1_DATA2 0x80000000
MX51_PAD_USBH1_DATA3__USBH1_DATA3 0x80000000
MX51_PAD_USBH1_DATA4__USBH1_DATA4 0x80000000
MX51_PAD_USBH1_DATA5__USBH1_DATA5 0x80000000
MX51_PAD_USBH1_DATA6__USBH1_DATA6 0x80000000
MX51_PAD_USBH1_DATA7__USBH1_DATA7 0x80000000
MX51_PAD_EIM_D21__GPIO2_5 0x80000000
>;
};
}; };
}; };
...@@ -547,3 +593,12 @@ MATRIX_KEY(3, 3, KEY_POWER) ...@@ -547,3 +593,12 @@ MATRIX_KEY(3, 3, KEY_POWER)
>; >;
status = "okay"; status = "okay";
}; };
&usbh1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh1>;
vbus-supply = <&reg_usb_vbus>;
fsl,usbphy = <&usbh1phy>;
phy_type = "ulpi";
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment