Commit 9c5c87e5 authored by Pavel Machek's avatar Pavel Machek Committed by Eduardo Valentin

ti-soc-thermal: implement omap3 support

This adds support for OMAP3 chips to ti-soc-thermal. As requested by
TI people, it is marked unreliable and warning is printed.
Signed-off-by: default avatarPavel Machek <pavel@ucw.cz>
Signed-off-by: default avatarEduardo Valentin <edubezval@gmail.com>
parent 3225031f
...@@ -10,6 +10,7 @@ to the silicon temperature. ...@@ -10,6 +10,7 @@ to the silicon temperature.
Required properties: Required properties:
- compatible : Should be: - compatible : Should be:
- "ti,omap34xx-bandgap" : for OMAP34xx bandgap
- "ti,omap4430-bandgap" : for OMAP4430 bandgap - "ti,omap4430-bandgap" : for OMAP4430 bandgap
- "ti,omap4460-bandgap" : for OMAP4460 bandgap - "ti,omap4460-bandgap" : for OMAP4460 bandgap
- "ti,omap4470-bandgap" : for OMAP4470 bandgap - "ti,omap4470-bandgap" : for OMAP4470 bandgap
...@@ -25,6 +26,12 @@ to each bandgap version, because the mapping may change from ...@@ -25,6 +26,12 @@ to each bandgap version, because the mapping may change from
soc to soc, apart of depending on available features. soc to soc, apart of depending on available features.
Example: Example:
OMAP34xx:
bandgap {
reg = <0x48002524 0x4>;
compatible = "ti,omap34xx-bandgap";
};
OMAP4430: OMAP4430:
bandgap { bandgap {
reg = <0x4a002260 0x4 0x4a00232C 0x4>; reg = <0x4a002260 0x4 0x4a00232C 0x4>;
......
...@@ -19,6 +19,21 @@ config TI_THERMAL ...@@ -19,6 +19,21 @@ config TI_THERMAL
This includes trip points definitions, extrapolation rules and This includes trip points definitions, extrapolation rules and
CPU cooling device bindings. CPU cooling device bindings.
config OMAP3_THERMAL
bool "Texas Instruments OMAP3 thermal support"
depends on TI_SOC_THERMAL
depends on ARCH_OMAP3 || COMPILE_TEST
help
If you say yes here you get thermal support for the Texas Instruments
OMAP3 SoC family. The current chips supported are:
- OMAP3430
OMAP3 chips normally don't need thermal management, and sensors in
this generation are not accurate, nor they are very close to
the important hotspots.
Say 'N' here.
config OMAP4_THERMAL config OMAP4_THERMAL
bool "Texas Instruments OMAP4 thermal support" bool "Texas Instruments OMAP4 thermal support"
depends on TI_SOC_THERMAL depends on TI_SOC_THERMAL
......
...@@ -2,5 +2,6 @@ obj-$(CONFIG_TI_SOC_THERMAL) += ti-soc-thermal.o ...@@ -2,5 +2,6 @@ obj-$(CONFIG_TI_SOC_THERMAL) += ti-soc-thermal.o
ti-soc-thermal-y := ti-bandgap.o ti-soc-thermal-y := ti-bandgap.o
ti-soc-thermal-$(CONFIG_TI_THERMAL) += ti-thermal-common.o ti-soc-thermal-$(CONFIG_TI_THERMAL) += ti-thermal-common.o
ti-soc-thermal-$(CONFIG_DRA752_THERMAL) += dra752-thermal-data.o ti-soc-thermal-$(CONFIG_DRA752_THERMAL) += dra752-thermal-data.o
ti-soc-thermal-$(CONFIG_OMAP3_THERMAL) += omap3-thermal-data.o
ti-soc-thermal-$(CONFIG_OMAP4_THERMAL) += omap4-thermal-data.o ti-soc-thermal-$(CONFIG_OMAP4_THERMAL) += omap4-thermal-data.o
ti-soc-thermal-$(CONFIG_OMAP5_THERMAL) += omap5-thermal-data.o ti-soc-thermal-$(CONFIG_OMAP5_THERMAL) += omap5-thermal-data.o
/*
* OMAP3 thermal driver.
*
* Copyright (C) 2011-2012 Texas Instruments Inc.
* Copyright (C) 2014 Pavel Machek <pavel@ucw.cz>
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Note
* http://www.ti.com/lit/er/sprz278f/sprz278f.pdf "Advisory
* 3.1.1.186 MMC OCP Clock Not Gated When Thermal Sensor Is Used"
*
* Also TI says:
* Just be careful when you try to make thermal policy like decisions
* based on this sensor. Placement of the sensor w.r.t the actual logic
* generating heat has to be a factor as well. If you are just looking
* for an approximation temperature (thermometerish kind), you might be
* ok with this. I am not sure we'd find any TI data around this.. just a
* heads up.
*/
#include "ti-thermal.h"
#include "ti-bandgap.h"
/*
* OMAP34XX has one instance of thermal sensor for MPU
* need to describe the individual bit fields
*/
static struct temp_sensor_registers
omap34xx_mpu_temp_sensor_registers = {
.temp_sensor_ctrl = 0,
.bgap_soc_mask = BIT(8),
.bgap_eocz_mask = BIT(7),
.bgap_dtemp_mask = 0x7f,
.bgap_mode_ctrl = 0,
.mode_ctrl_mask = BIT(9),
};
/* Thresholds and limits for OMAP34XX MPU temperature sensor */
static struct temp_sensor_data omap34xx_mpu_temp_sensor_data = {
.min_freq = 32768,
.max_freq = 32768,
.max_temp = 125000,
.min_temp = -40000,
.hyst_val = 5000,
};
/*
* Temperature values in milli degree celsius
*/
static const int
omap34xx_adc_to_temp[128] = {
-40000, -40000, -40000, -40000, -40000, -39000, -38000, -36000,
-34000, -32000, -31000, -29000, -28000, -26000, -25000, -24000,
-22000, -21000, -19000, -18000, -17000, -15000, -14000, -12000,
-11000, -9000, -8000, -7000, -5000, -4000, -2000, -1000, 0000,
1000, 3000, 4000, 5000, 7000, 8000, 10000, 11000, 13000, 14000,
15000, 17000, 18000, 20000, 21000, 22000, 24000, 25000, 27000,
28000, 30000, 31000, 32000, 34000, 35000, 37000, 38000, 39000,
41000, 42000, 44000, 45000, 47000, 48000, 49000, 51000, 52000,
53000, 55000, 56000, 58000, 59000, 60000, 62000, 63000, 65000,
66000, 67000, 69000, 70000, 72000, 73000, 74000, 76000, 77000,
79000, 80000, 81000, 83000, 84000, 85000, 87000, 88000, 89000,
91000, 92000, 94000, 95000, 96000, 98000, 99000, 100000,
102000, 103000, 105000, 106000, 107000, 109000, 110000, 111000,
113000, 114000, 116000, 117000, 118000, 120000, 121000, 122000,
124000, 124000, 125000, 125000, 125000, 125000, 125000
};
/* OMAP34XX data */
const struct ti_bandgap_data omap34xx_data = {
.features = TI_BANDGAP_FEATURE_CLK_CTRL | TI_BANDGAP_FEATURE_UNRELIABLE,
.fclock_name = "ts_fck",
.div_ck_name = "ts_fck",
.conv_table = omap34xx_adc_to_temp,
.adc_start_val = 0,
.adc_end_val = 127,
.expose_sensor = ti_thermal_expose_sensor,
.remove_sensor = ti_thermal_remove_sensor,
.sensors = {
{
.registers = &omap34xx_mpu_temp_sensor_registers,
.ts_data = &omap34xx_mpu_temp_sensor_data,
.domain = "cpu",
.slope = 0,
.constant = 20000,
.slope_pcb = 0,
.constant_pcb = 20000,
.register_cooling = NULL,
.unregister_cooling = NULL,
},
},
.sensor_count = 1,
};
...@@ -1274,6 +1274,10 @@ int ti_bandgap_probe(struct platform_device *pdev) ...@@ -1274,6 +1274,10 @@ int ti_bandgap_probe(struct platform_device *pdev)
} }
bgp->dev = &pdev->dev; bgp->dev = &pdev->dev;
if (TI_BANDGAP_HAS(bgp, UNRELIABLE))
dev_warn(&pdev->dev,
"This OMAP thermal sensor is unreliable. You've been warned\n");
if (TI_BANDGAP_HAS(bgp, TSHUT)) { if (TI_BANDGAP_HAS(bgp, TSHUT)) {
ret = ti_bandgap_tshut_init(bgp, pdev); ret = ti_bandgap_tshut_init(bgp, pdev);
if (ret) { if (ret) {
...@@ -1579,6 +1583,12 @@ static SIMPLE_DEV_PM_OPS(ti_bandgap_dev_pm_ops, ti_bandgap_suspend, ...@@ -1579,6 +1583,12 @@ static SIMPLE_DEV_PM_OPS(ti_bandgap_dev_pm_ops, ti_bandgap_suspend,
#endif #endif
static const struct of_device_id of_ti_bandgap_match[] = { static const struct of_device_id of_ti_bandgap_match[] = {
#ifdef CONFIG_OMAP3_THERMAL
{
.compatible = "ti,omap34xx-bandgap",
.data = (void *)&omap34xx_data,
},
#endif
#ifdef CONFIG_OMAP4_THERMAL #ifdef CONFIG_OMAP4_THERMAL
{ {
.compatible = "ti,omap4430-bandgap", .compatible = "ti,omap4430-bandgap",
......
...@@ -322,6 +322,8 @@ struct ti_temp_sensor { ...@@ -322,6 +322,8 @@ struct ti_temp_sensor {
* has Errata 814 * has Errata 814
* TI_BANDGAP_FEATURE_ERRATA_813 - used to workaorund when the bandgap device * TI_BANDGAP_FEATURE_ERRATA_813 - used to workaorund when the bandgap device
* has Errata 813 * has Errata 813
* TI_BANDGAP_FEATURE_UNRELIABLE - used when the sensor readings are too
* inaccurate.
* TI_BANDGAP_HAS(b, f) - macro to check if a bandgap device is capable of a * TI_BANDGAP_HAS(b, f) - macro to check if a bandgap device is capable of a
* specific feature (above) or not. Return non-zero, if yes. * specific feature (above) or not. Return non-zero, if yes.
*/ */
...@@ -337,6 +339,7 @@ struct ti_temp_sensor { ...@@ -337,6 +339,7 @@ struct ti_temp_sensor {
#define TI_BANDGAP_FEATURE_HISTORY_BUFFER BIT(9) #define TI_BANDGAP_FEATURE_HISTORY_BUFFER BIT(9)
#define TI_BANDGAP_FEATURE_ERRATA_814 BIT(10) #define TI_BANDGAP_FEATURE_ERRATA_814 BIT(10)
#define TI_BANDGAP_FEATURE_ERRATA_813 BIT(11) #define TI_BANDGAP_FEATURE_ERRATA_813 BIT(11)
#define TI_BANDGAP_FEATURE_UNRELIABLE BIT(12)
#define TI_BANDGAP_HAS(b, f) \ #define TI_BANDGAP_HAS(b, f) \
((b)->conf->features & TI_BANDGAP_FEATURE_ ## f) ((b)->conf->features & TI_BANDGAP_FEATURE_ ## f)
...@@ -390,6 +393,12 @@ int ti_bandgap_set_sensor_data(struct ti_bandgap *bgp, int id, void *data); ...@@ -390,6 +393,12 @@ int ti_bandgap_set_sensor_data(struct ti_bandgap *bgp, int id, void *data);
void *ti_bandgap_get_sensor_data(struct ti_bandgap *bgp, int id); void *ti_bandgap_get_sensor_data(struct ti_bandgap *bgp, int id);
int ti_bandgap_get_trend(struct ti_bandgap *bgp, int id, int *trend); int ti_bandgap_get_trend(struct ti_bandgap *bgp, int id, int *trend);
#ifdef CONFIG_OMAP3_THERMAL
extern const struct ti_bandgap_data omap34xx_data;
#else
#define omap34xx_data NULL
#endif
#ifdef CONFIG_OMAP4_THERMAL #ifdef CONFIG_OMAP4_THERMAL
extern const struct ti_bandgap_data omap4430_data; extern const struct ti_bandgap_data omap4430_data;
extern const struct ti_bandgap_data omap4460_data; extern const struct ti_bandgap_data omap4460_data;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment