Merge tag 'bcm2835-dt-next-2017-06-08' into bcm2835-dt-64-next

This merge brings in the cpu-thermal node we in bcm283x that we need
in order to set the rpi3's coefficients.

arch/arm/boot/dts/Makefile

@@ -72,6 +72,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2835-rpi-b-plus.dtb \
 	bcm2835-rpi-a-plus.dtb \
 	bcm2836-rpi-2-b.dtb \
+	bcm2837-rpi-3-b.dtb \
 	bcm2835-rpi-zero.dtb
 dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4708-asus-rt-ac56u.dtb \

arch/arm/boot/dts/bcm2835-rpi.dtsi

@@ -65,13 +65,13 @@ &i2c2 {
 &sdhci {
 	pinctrl-names = "default";
 	pinctrl-0 = <&emmc_gpio48>;
-	status = "okay";
 	bus-width = <4>;
 };
 
 &sdhost {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
 	bus-width = <4>;
 };
 

arch/arm/boot/dts/bcm2835.dtsi

@@ -24,6 +24,10 @@ arm-pmu {
 	};
 };
 
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
 /* enable thermal sensor with the correct compatible property set */
 &thermal {
 	compatible = "brcm,bcm2835-thermal";

arch/arm/boot/dts/bcm2836.dtsi

@@ -77,6 +77,10 @@ &intc {
 	interrupts = <8>;
 };
 
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
 /* enable thermal sensor with the correct compatible property set */
 &thermal {
 	compatible = "brcm,bcm2836-thermal";

arch/arm/boot/dts/bcm2837-rpi-3-b.dts

+#include "arm64/broadcom/bcm2837-rpi-3-b.dts"

arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi

 / {
 	aliases {
-		ethernet = &ethernet;
+		ethernet0 = &ethernet;
 	};
 };
 

arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi

 / {
 	aliases {
-		ethernet = &ethernet;
+		ethernet0 = &ethernet;
 	};
 };
 

arch/arm/boot/dts/bcm283x.dtsi

@@ -19,6 +19,26 @@ chosen {
 		bootargs = "earlyprintk console=ttyAMA0";
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <80000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+
+			cooling-maps {
+			};
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -198,8 +218,8 @@ i2c0_gpio0: i2c0_gpio0 {
 				brcm,pins = <0 1>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			i2c0_gpio32: i2c0_gpio32 {
-				brcm,pins = <32 34>;
+			i2c0_gpio28: i2c0_gpio28 {
+				brcm,pins = <28 29>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
 			i2c0_gpio44: i2c0_gpio44 {
@@ -295,20 +315,28 @@ uart0_gpio14: uart0_gpio14 {
 			/* Separate from the uart0_gpio14 group
 			 * because it conflicts with spi1_gpio16, and
 			 * people often run uart0 on the two pins
-			 * without flow contrl.
+			 * without flow control.
 			 */
 			uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
 				brcm,pins = <16 17>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
-			uart0_gpio30: uart0_gpio30 {
+			uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
 				brcm,pins = <30 31>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
-			uart0_ctsrts_gpio32: uart0_ctsrts_gpio32 {
+			uart0_gpio32: uart0_gpio32 {
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
+			uart0_gpio36: uart0_gpio36 {
+				brcm,pins = <36 37>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
+			uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 {
+				brcm,pins = <38 39>;
+				brcm,function = <BCM2835_FSEL_ALT2>;
+			};
 
 			uart1_gpio14: uart1_gpio14 {
 				brcm,pins = <14 15>;
@@ -326,10 +354,6 @@ uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
 				brcm,pins = <30 31>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_gpio36: uart1_gpio36 {
-				brcm,pins = <36 37 38 39>;
-				brcm,function = <BCM2835_FSEL_ALT2>;
-			};
 			uart1_gpio40: uart1_gpio40 {
 				brcm,pins = <40 41>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
@@ -426,6 +450,7 @@ thermal: thermal@7e212000 {
 			compatible = "brcm,bcm2835-thermal";
 			reg = <0x7e212000 0x8>;
 			clocks = <&clocks BCM2835_CLOCK_TSENS>;
+			#thermal-sensor-cells = <0>;
 			status = "disabled";
 		};