Commit 9f01efaa authored by Ben Dooks's avatar Ben Dooks

[ARM] S3C2440: Merge branch next-mini2440 into next-s3c

Merge branch 'next-mini2440' into next-s3c
parents 9d76295a 799ca065
...@@ -1358,6 +1358,27 @@ and is between 256 and 4096 characters. It is defined in the file ...@@ -1358,6 +1358,27 @@ and is between 256 and 4096 characters. It is defined in the file
min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
physical address is ignored. physical address is ignored.
mini2440= [ARM,HW,KNL]
Format:[0..2][b][c][t]
Default: "0tb"
MINI2440 configuration specification:
0 - The attached screen is the 3.5" TFT
1 - The attached screen is the 7" TFT
2 - The VGA Shield is attached (1024x768)
Leaving out the screen size parameter will not load
the TFT driver, and the framebuffer will be left
unconfigured.
b - Enable backlight. The TFT backlight pin will be
linked to the kernel VESA blanking code and a GPIO
LED. This parameter is not necessary when using the
VGA shield.
c - Enable the s3c camera interface.
t - Reserved for enabling touchscreen support. The
touchscreen support is not enabled in the mainstream
kernel as of 2.6.30, a preliminary port can be found
in the "bleeding edge" mini2440 support kernel at
http://repo.or.cz/w/linux-2.6/mini2440.git
mminit_loglevel= mminit_loglevel=
[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
parameter allows control of the logging verbosity for parameter allows control of the logging verbosity for
......
This diff is collapsed.
...@@ -84,5 +84,15 @@ config MACH_AT2440EVB ...@@ -84,5 +84,15 @@ config MACH_AT2440EVB
help help
Say Y here if you are using the AT2440EVB development board Say Y here if you are using the AT2440EVB development board
config MACH_MINI2440
bool "MINI2440 development board"
select CPU_S3C2440
select EEPROM_AT24
select LEDS_TRIGGER_BACKLIGHT
select SND_S3C24XX_SOC_S3C24XX_UDA134X
help
Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
available via various sources. It can come with a 3.5" or 7" touch LCD.
endmenu endmenu
...@@ -22,3 +22,4 @@ obj-$(CONFIG_MACH_RX3715) += mach-rx3715.o ...@@ -22,3 +22,4 @@ obj-$(CONFIG_MACH_RX3715) += mach-rx3715.o
obj-$(CONFIG_ARCH_S3C2440) += mach-smdk2440.o obj-$(CONFIG_ARCH_S3C2440) += mach-smdk2440.o
obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o
obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o
obj-$(CONFIG_MACH_MINI2440) += mach-mini2440.o
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment