Merge tag 'zynq-soc-for-v5.0' of https://github.com/Xilinx/linux-xlnx into next/drivers

ARM: Xilinx Zynq SoC patches for v5.0

- Adding pl353 smc driver

* tag 'zynq-soc-for-v5.0' of https://github.com/Xilinx/linux-xlnx:
  memory: pl353: Add driver for arm pl353 static memory controller
  dt-bindings: memory: Add pl353 smc controller devicetree binding information
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/memory-controllers/pl353-smc.txt

+Device tree bindings for ARM PL353 static memory controller
+
+PL353 static memory controller supports two kinds of memory
+interfaces.i.e NAND and SRAM/NOR interfaces.
+The actual devices are instantiated from the child nodes of pl353 smc node.
+
+Required properties:
+- compatible		: Should be "arm,pl353-smc-r2p1", "arm,primecell".
+- reg			: Controller registers map and length.
+- clock-names		: List of input clock names - "memclk", "apb_pclk"
+			  (See clock bindings for details).
+- clocks		: Clock phandles (see clock bindings for details).
+- address-cells		: Must be 2.
+- size-cells		: Must be 1.
+
+Child nodes:
+ For NAND the "arm,pl353-nand-r2p1" and for NOR the "cfi-flash" drivers are
+supported as child nodes.
+
+for NAND partition information please refer the below file
+Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+	smcc: memory-controller@e000e000
+			compatible = "arm,pl353-smc-r2p1", "arm,primecell";
+			clock-names = "memclk", "apb_pclk";
+			clocks = <&clkc 11>, <&clkc 44>;
+			reg = <0xe000e000 0x1000>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0xe1000000 0x1000000 //Nand CS Region
+				  0x1 0x0 0xe2000000 0x2000000 //SRAM/NOR CS Region
+				  0x2 0x0 0xe4000000 0x2000000>; //SRAM/NOR CS Region
+			nand_0: flash@e1000000 {
+				compatible = "arm,pl353-nand-r2p1"
+				reg = <0 0 0x1000000>;
+				(...)
+			};
+			nor0: flash@e2000000 {
+				compatible = "cfi-flash";
+				reg = <1 0 0x2000000>;
+			};
+			nor1: flash@e4000000 {
+				compatible = "cfi-flash";
+				reg = <2 0 0x2000000>;
+			};
+	};

drivers/memory/Kconfig

@@ -145,6 +145,15 @@ config DA8XX_DDRCTL
 	  Texas Instruments da8xx SoCs. It's used to tweak various memory
 	  controller configuration options.
 
+config PL353_SMC
+	tristate "ARM PL35X Static Memory Controller(SMC) driver"
+	default y
+	depends on ARM
+	depends on ARM_AMBA
+	help
+	  This driver is for the ARM PL351/PL353 Static Memory
+	  Controller(SMC) module.
+
 source "drivers/memory/samsung/Kconfig"
 source "drivers/memory/tegra/Kconfig"
 

drivers/memory/Makefile

@@ -19,6 +19,7 @@ obj-$(CONFIG_MVEBU_DEVBUS)	+= mvebu-devbus.o
 obj-$(CONFIG_JZ4780_NEMC)	+= jz4780-nemc.o
 obj-$(CONFIG_MTK_SMI)		+= mtk-smi.o
 obj-$(CONFIG_DA8XX_DDRCTL)	+= da8xx-ddrctl.o
+obj-$(CONFIG_PL353_SMC)		+= pl353-smc.o
 
 obj-$(CONFIG_SAMSUNG_MC)	+= samsung/
 obj-$(CONFIG_TEGRA_MC)		+= tegra/

include/linux/pl353-smc.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * ARM PL353 SMC Driver Header
+ *
+ * Copyright (C) 2012 - 2018 Xilinx, Inc
+ */
+
+#ifndef __LINUX_PL353_SMC_H
+#define __LINUX_PL353_SMC_H
+
+enum pl353_smc_ecc_mode {
+	PL353_SMC_ECCMODE_BYPASS = 0,
+	PL353_SMC_ECCMODE_APB = 1,
+	PL353_SMC_ECCMODE_MEM = 2
+};
+
+enum pl353_smc_mem_width {
+	PL353_SMC_MEM_WIDTH_8 = 0,
+	PL353_SMC_MEM_WIDTH_16 = 1
+};
+
+u32 pl353_smc_get_ecc_val(int ecc_reg);
+bool pl353_smc_ecc_is_busy(void);
+int pl353_smc_get_nand_int_status_raw(void);
+void pl353_smc_clr_nand_int(void);
+int pl353_smc_set_ecc_mode(enum pl353_smc_ecc_mode mode);
+int pl353_smc_set_ecc_pg_size(unsigned int pg_sz);
+int pl353_smc_set_buswidth(unsigned int bw);
+void pl353_smc_set_cycles(u32 timings[]);
+#endif