media: rcar-csi2: Propagate the FLD signal for NTSC and PAL

Depending on which video standard is used the driver needs to setup the
hardware to correctly handle fields. If stream is identified as NTSC
or PAL setup field detection and propagate the field detection signal.

Later versions of the datasheet have been updated to make it clear
that FLD register should be set to 0 when dealing with non-interlaced
field formats.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

drivers/media/platform/rcar-vin/rcar-csi2.c

@@ -68,6 +68,7 @@ struct rcar_csi2;
 /* Field Detection Control */
 #define FLD_REG				0x1c
 #define FLD_FLD_NUM(n)			(((n) & 0xff) << 16)
+#define FLD_DET_SEL(n)			(((n) & 0x3) << 4)
 #define FLD_FLD_EN4			BIT(3)
 #define FLD_FLD_EN3			BIT(2)
 #define FLD_FLD_EN2			BIT(1)
@@ -478,7 +479,7 @@ static int rcsi2_calc_mbps(struct rcar_csi2 *priv, unsigned int bpp)
 static int rcsi2_start_receiver(struct rcar_csi2 *priv)
 {
 	const struct rcar_csi2_format *format;
-	u32 phycnt, vcdt = 0, vcdt2 = 0;
+	u32 phycnt, vcdt = 0, vcdt2 = 0, fld = 0;
 	unsigned int i;
 	int mbps, ret;
 
@@ -510,6 +511,16 @@ static int rcsi2_start_receiver(struct rcar_csi2 *priv)
 			vcdt2 |= vcdt_part << ((i % 2) * 16);
 	}
 
+	if (priv->mf.field == V4L2_FIELD_ALTERNATE) {
+		fld = FLD_DET_SEL(1) | FLD_FLD_EN4 | FLD_FLD_EN3 | FLD_FLD_EN2
+			| FLD_FLD_EN;
+
+		if (priv->mf.height == 240)
+			fld |= FLD_FLD_NUM(0);
+		else
+			fld |= FLD_FLD_NUM(1);
+	}
+
 	phycnt = PHYCNT_ENABLECLK;
 	phycnt |= (1 << priv->lanes) - 1;
 
@@ -556,8 +567,7 @@ static int rcsi2_start_receiver(struct rcar_csi2 *priv)
 	rcsi2_write(priv, PHYCNT_REG, phycnt);
 	rcsi2_write(priv, LINKCNT_REG, LINKCNT_MONITOR_EN |
 		    LINKCNT_REG_MONI_PACT_EN | LINKCNT_ICLK_NONSTOP);
-	rcsi2_write(priv, FLD_REG, FLD_FLD_NUM(2) | FLD_FLD_EN4 |
-		    FLD_FLD_EN3 | FLD_FLD_EN2 | FLD_FLD_EN);
+	rcsi2_write(priv, FLD_REG, fld);
 	rcsi2_write(priv, PHYCNT_REG, phycnt | PHYCNT_SHUTDOWNZ);
 	rcsi2_write(priv, PHYCNT_REG, phycnt | PHYCNT_SHUTDOWNZ | PHYCNT_RSTZ);