Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (44 commits)
  hwmon: Support for Dallas Semiconductor DS620
  hwmon: driver for Sensirion SHT21 humidity and temperature sensor
  hwmon: Add humidity attribute to sysfs ABI
  hwmon: sysfs ABI updates
  hwmon: (via-cputemp) sync hotplug handling with coretemp/pkgtemp
  hwmon: (lm95241) Rewrite to avoid using macros
  hwmon: (applesmc) Fix checkpatch errors and fix value range checks
  hwmon: (applesmc) Update copyright information
  hwmon: (applesmc) Silence driver
  hwmon: (applesmc) Simplify feature sysfs handling
  hwmon: (applesmc) Dynamic creation of fan files
  hwmon: (applesmc) Extract all features generically
  hwmon: (applesmc) Handle new temperature format
  hwmon: (applesmc) Dynamic creation of temperature files
  hwmon: (applesmc) Introduce a register lookup table
  hwmon: (applesmc) Use pr_fmt and pr_<level>
  hwmon: (applesmc) Relax the severity of device init failure
  hwmon: (applesmc) Add MacBookAir3,1(3,2) support
  hwmon: (w83627hf) Use pr_fmt and pr_<level>
  hwmon: (w83627ehf) Use pr_fmt and pr_<level>
  ...

Documentation/hwmon/ds620

+Kernel driver ds620
+===================
+
+Supported chips:
+  * Dallas Semiconductor DS620
+    Prefix: 'ds620'
+    Datasheet: Publicly available at the Dallas Semiconductor website
+               http://www.dalsemi.com/
+
+Authors:
+        Roland Stigge <stigge@antcom.de>
+        based on ds1621.c by
+        Christian W. Zuckschwerdt <zany@triq.net>
+
+Description
+-----------
+
+The DS620 is a (one instance) digital thermometer and thermostat. It has both
+high and low temperature limits which can be user defined (i.e.  programmed
+into non-volatile on-chip registers). Temperature range is -55 degree Celsius
+to +125. Between 0 and 70 degree Celsius, accuracy is 0.5 Kelvin. The value
+returned via sysfs displays post decimal positions.
+
+The thermostat function works as follows: When configured via platform_data
+(struct ds620_platform_data) .pomode == 0 (default), the thermostat output pin
+PO is always low. If .pomode == 1, the thermostat is in PO_LOW mode. I.e., the
+output pin PO becomes active when the temperature falls below temp1_min and
+stays active until the temperature goes above temp1_max.
+
+Likewise, with .pomode == 2, the thermostat is in PO_HIGH mode. I.e., the PO
+output pin becomes active when the temperature goes above temp1_max and stays
+active until the temperature falls below temp1_min.
+
+The PO output pin of the DS620 operates active-low.

Documentation/hwmon/sht21

+Kernel driver sht21
+===================
+
+Supported chips:
+  * Sensirion SHT21
+    Prefix: 'sht21'
+    Addresses scanned: none
+    Datasheet: Publicly available at the Sensirion website
+    http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT21.pdf
+
+  * Sensirion SHT25
+    Prefix: 'sht21'
+    Addresses scanned: none
+    Datasheet: Publicly available at the Sensirion website
+    http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT25.pdf
+
+Author:
+  Urs Fleisch <urs.fleisch@sensirion.com>
+
+Description
+-----------
+
+The SHT21 and SHT25 are humidity and temperature sensors in a DFN package of
+only 3 x 3 mm footprint and 1.1 mm height. The difference between the two
+devices is the higher level of precision of the SHT25 (1.8% relative humidity,
+0.2 degree Celsius) compared with the SHT21 (2.0% relative humidity,
+0.3 degree Celsius).
+
+The devices communicate with the I2C protocol. All sensors are set to the same
+I2C address 0x40, so an entry with I2C_BOARD_INFO("sht21", 0x40) can be used
+in the board setup code.
+
+sysfs-Interface
+---------------
+
+temp1_input - temperature input
+humidity1_input - humidity input
+
+Notes
+-----
+
+The driver uses the default resolution settings of 12 bit for humidity and 14
+bit for temperature, which results in typical measurement times of 22 ms for
+humidity and 66 ms for temperature. To keep self heating below 0.1 degree
+Celsius, the device should not be active for more than 10% of the time,
+e.g. maximum two measurements per second at the given resolution.
+
+Different resolutions, the on-chip heater, using the CRC checksum and reading
+the serial number are not supported yet.

Documentation/hwmon/sysfs-interface

@@ -384,10 +384,20 @@ curr[1-*]_min	Current min value.
 		Unit: milliampere
 		RW
 
+curr[1-*]_lcrit	Current critical low value
+		Unit: milliampere
+		RW
+
+curr[1-*]_crit	Current critical high value.
+		Unit: milliampere
+		RW
+
 curr[1-*]_input	Current input value
 		Unit: milliampere
 		RO
 
+Also see the Alarms section for status flags associated with currents.
+
 *********
 * Power *
 *********
@@ -450,13 +460,6 @@ power[1-*]_accuracy		Accuracy of the power meter.
 				Unit: Percent
 				RO
 
-power[1-*]_alarm		1 if the system is drawing more power than the
-				cap allows; 0 otherwise.  A poll notification is
-				sent to this file when the power use exceeds the
-				cap.  This file only appears if the cap is known
-				to be enforced by hardware.
-				RO
-
 power[1-*]_cap			If power use rises above this limit, the
 				system should take action to reduce power use.
 				A poll notification is sent to this file if the
@@ -479,6 +482,20 @@ power[1-*]_cap_min		Minimum cap that can be set.
 				Unit: microWatt
 				RO
 
+power[1-*]_max			Maximum power.
+				Unit: microWatt
+				RW
+
+power[1-*]_crit			Critical maximum power.
+				If power rises to or above this limit, the
+				system is expected take drastic action to reduce
+				power consumption, such as a system shutdown or
+				a forced powerdown of some devices.
+				Unit: microWatt
+				RW
+
+Also see the Alarms section for status flags associated with power readings.
+
 **********
 * Energy *
 **********
@@ -488,6 +505,15 @@ energy[1-*]_input		Cumulative energy use
 				RO
 
 
+************
+* Humidity *
+************
+
+humidity[1-*]_input		Humidity
+				Unit: milli-percent (per cent mille, pcm)
+				RO
+
+
 **********
 * Alarms *
 **********
@@ -501,6 +527,7 @@ implementation.
 
 in[0-*]_alarm
 curr[1-*]_alarm
+power[1-*]_alarm
 fan[1-*]_alarm
 temp[1-*]_alarm
 		Channel alarm
@@ -512,12 +539,20 @@ OR
 
 in[0-*]_min_alarm
 in[0-*]_max_alarm
+in[0-*]_lcrit_alarm
+in[0-*]_crit_alarm
 curr[1-*]_min_alarm
 curr[1-*]_max_alarm
+curr[1-*]_lcrit_alarm
+curr[1-*]_crit_alarm
+power[1-*]_cap_alarm
+power[1-*]_max_alarm
+power[1-*]_crit_alarm
 fan[1-*]_min_alarm
 fan[1-*]_max_alarm
 temp[1-*]_min_alarm
 temp[1-*]_max_alarm
+temp[1-*]_lcrit_alarm
 temp[1-*]_crit_alarm
 temp[1-*]_emergency_alarm
 		Limit alarm

drivers/hwmon/Kconfig

@@ -274,6 +274,16 @@ config SENSORS_ATXP1
 	  This driver can also be built as a module.  If so, the module
 	  will be called atxp1.
 
+config SENSORS_DS620
+	tristate "Dallas Semiconductor DS620"
+	depends on I2C
+	help
+	  If you say yes here you get support for Dallas Semiconductor
+	  DS620 sensor chip.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called ds620.
+
 config SENSORS_DS1621
 	tristate "Dallas Semiconductor DS1621 and DS1625"
 	depends on I2C
@@ -734,6 +744,16 @@ config SENSORS_SHT15
 	  This driver can also be built as a module.  If so, the module
 	  will be called sht15.
 
+config SENSORS_SHT21
+	tristate "Sensiron humidity and temperature sensors. SHT21 and compat."
+	depends on I2C
+	help
+	  If you say yes here you get support for the Sensiron SHT21, SHT25
+	  humidity and temperature sensors.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called sht21.
+
 config SENSORS_S3C
 	tristate "Samsung built-in ADC"
 	depends on S3C_ADC

drivers/hwmon/Makefile

@@ -41,6 +41,7 @@ obj-$(CONFIG_SENSORS_ATXP1)	+= atxp1.o
 obj-$(CONFIG_SENSORS_CORETEMP)	+= coretemp.o
 obj-$(CONFIG_SENSORS_PKGTEMP)	+= pkgtemp.o
 obj-$(CONFIG_SENSORS_DME1737)	+= dme1737.o
+obj-$(CONFIG_SENSORS_DS620)	+= ds620.o
 obj-$(CONFIG_SENSORS_DS1621)	+= ds1621.o
 obj-$(CONFIG_SENSORS_EMC1403)	+= emc1403.o
 obj-$(CONFIG_SENSORS_EMC2103)	+= emc2103.o
@@ -90,6 +91,7 @@ obj-$(CONFIG_SENSORS_PC87427)	+= pc87427.o
 obj-$(CONFIG_SENSORS_PCF8591)	+= pcf8591.o
 obj-$(CONFIG_SENSORS_S3C)	+= s3c-hwmon.o
 obj-$(CONFIG_SENSORS_SHT15)	+= sht15.o
+obj-$(CONFIG_SENSORS_SHT21)	+= sht21.o
 obj-$(CONFIG_SENSORS_SIS5595)	+= sis5595.o
 obj-$(CONFIG_SENSORS_SMM665)	+= smm665.o
 obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o

drivers/hwmon/abituguru.c

@@ -20,6 +20,9 @@
     the custom Abit uGuru chip found on Abit uGuru motherboards. Note: because
     of lack of specs the CPU/RAM voltage & frequency control is not supported!
 */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/sched.h>
 #include <linux/init.h>
@@ -220,6 +223,10 @@ struct abituguru_data {
 	u8 pwm_settings[ABIT_UGURU_MAX_PWMS][5];
 };
 
+static const char *never_happen = "This should never happen.";
+static const char *report_this =
+	"Please report this to the abituguru maintainer (see MAINTAINERS)";
+
 /* wait till the uguru is in the specified state */
 static int abituguru_wait(struct abituguru_data *data, u8 state)
 {
@@ -438,8 +445,7 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
 
 	/* Test val is sane / usable for sensor type detection. */
 	if ((val < 10u) || (val > 250u)) {
-		printk(KERN_WARNING ABIT_UGURU_NAME
-			": bank1-sensor: %d reading (%d) too close to limits, "
+		pr_warn("bank1-sensor: %d reading (%d) too close to limits, "
 			"unable to determine sensor type, skipping sensor\n",
 			(int)sensor_addr, (int)val);
 		/* assume no sensor is there for sensors for which we can't
@@ -535,10 +541,8 @@ abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
 				3) == 3)
 			break;
 	if (i == 3) {
-		printk(KERN_ERR ABIT_UGURU_NAME
-			": Fatal error could not restore original settings. "
-			"This should never happen please report this to the "
-			"abituguru maintainer (see MAINTAINERS)\n");
+		pr_err("Fatal error could not restore original settings. %s %s\n",
+		       never_happen, report_this);
 		return -ENODEV;
 	}
 	return ret;
@@ -1268,14 +1272,12 @@ static int __devinit abituguru_probe(struct platform_device *pdev)
 	}
 	/* Fail safe check, this should never happen! */
 	if (sysfs_names_free < 0) {
-		printk(KERN_ERR ABIT_UGURU_NAME ": Fatal error ran out of "
-		       "space for sysfs attr names. This should never "
-		       "happen please report to the abituguru maintainer "
-		       "(see MAINTAINERS)\n");
+		pr_err("Fatal error ran out of space for sysfs attr names. %s %s",
+		       never_happen, report_this);
 		res = -ENAMETOOLONG;
 		goto abituguru_probe_error;
 	}
-	printk(KERN_INFO ABIT_UGURU_NAME ": found Abit uGuru\n");
+	pr_info("found Abit uGuru\n");
 
 	/* Register sysfs hooks */
 	for (i = 0; i < sysfs_attr_i; i++)
@@ -1432,8 +1434,7 @@ static int __init abituguru_detect(void)
 		"0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val);
 
 	if (force) {
-		printk(KERN_INFO ABIT_UGURU_NAME ": Assuming Abit uGuru is "
-				"present because of \"force\" parameter\n");
+		pr_info("Assuming Abit uGuru is present because of \"force\" parameter\n");
 		return ABIT_UGURU_BASE;
 	}
 
@@ -1467,8 +1468,7 @@ static int __init abituguru_init(void)
 
 	abituguru_pdev = platform_device_alloc(ABIT_UGURU_NAME, address);
 	if (!abituguru_pdev) {
-		printk(KERN_ERR ABIT_UGURU_NAME
-			": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		err = -ENOMEM;
 		goto exit_driver_unregister;
 	}
@@ -1479,15 +1479,13 @@ static int __init abituguru_init(void)
 
 	err = platform_device_add_resources(abituguru_pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR ABIT_UGURU_NAME
-			": Device resource addition failed (%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(abituguru_pdev);
 	if (err) {
-		printk(KERN_ERR ABIT_UGURU_NAME
-			": Device addition failed (%d)\n", err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 

drivers/hwmon/abituguru3.c

@@ -23,6 +23,9 @@
     chip found on newer Abit uGuru motherboards. Note: because of lack of specs
     only reading the sensors and their settings is supported.
 */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -608,6 +611,9 @@ static int verbose = 1;
 module_param(verbose, bool, 0644);
 MODULE_PARM_DESC(verbose, "Enable/disable verbose error reporting");
 
+static const char *never_happen = "This should never happen.";
+static const char *report_this =
+	"Please report this to the abituguru3 maintainer (see MAINTAINERS)";
 
 /* wait while the uguru is busy (usually after a write) */
 static int abituguru3_wait_while_busy(struct abituguru3_data *data)
@@ -940,15 +946,13 @@ static int __devinit abituguru3_probe(struct platform_device *pdev)
 		if (abituguru3_motherboards[i].id == id)
 			break;
 	if (!abituguru3_motherboards[i].id) {
-		printk(KERN_ERR ABIT_UGURU3_NAME ": error unknown motherboard "
-			"ID: %04X. Please report this to the abituguru3 "
-			"maintainer (see MAINTAINERS)\n", (unsigned int)id);
+		pr_err("error unknown motherboard ID: %04X. %s\n",
+		       (unsigned int)id, report_this);
 		goto abituguru3_probe_error;
 	}
 	data->sensors = abituguru3_motherboards[i].sensors;
 
-	printk(KERN_INFO ABIT_UGURU3_NAME ": found Abit uGuru3, motherboard "
-		"ID: %04X\n", (unsigned int)id);
+	pr_info("found Abit uGuru3, motherboard ID: %04X\n", (unsigned int)id);
 
 	/* Fill the sysfs attr array */
 	sysfs_attr_i = 0;
@@ -957,11 +961,8 @@ static int __devinit abituguru3_probe(struct platform_device *pdev)
 	for (i = 0; data->sensors[i].name; i++) {
 		/* Fail safe check, this should never happen! */
 		if (i >= ABIT_UGURU3_MAX_NO_SENSORS) {
-			printk(KERN_ERR ABIT_UGURU3_NAME
-				": Fatal error motherboard has more sensors "
-				"then ABIT_UGURU3_MAX_NO_SENSORS. This should "
-				"never happen please report to the abituguru3 "
-				"maintainer (see MAINTAINERS)\n");
+			pr_err("Fatal error motherboard has more sensors then ABIT_UGURU3_MAX_NO_SENSORS. %s %s\n",
+			       never_happen, report_this);
 			res = -ENAMETOOLONG;
 			goto abituguru3_probe_error;
 		}
@@ -983,10 +984,8 @@ static int __devinit abituguru3_probe(struct platform_device *pdev)
 	}
 	/* Fail safe check, this should never happen! */
 	if (sysfs_names_free < 0) {
-		printk(KERN_ERR ABIT_UGURU3_NAME
-			": Fatal error ran out of space for sysfs attr names. "
-			"This should never happen please report to the "
-			"abituguru3 maintainer (see MAINTAINERS)\n");
+		pr_err("Fatal error ran out of space for sysfs attr names. %s %s\n",
+		       never_happen, report_this);
 		res = -ENAMETOOLONG;
 		goto abituguru3_probe_error;
 	}
@@ -1189,8 +1188,7 @@ static int __init abituguru3_detect(void)
 		"0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val);
 
 	if (force) {
-		printk(KERN_INFO ABIT_UGURU3_NAME ": Assuming Abit uGuru3 is "
-				"present because of \"force\" parameter\n");
+		pr_info("Assuming Abit uGuru3 is present because of \"force\" parameter\n");
 		return 0;
 	}
 
@@ -1219,10 +1217,8 @@ static int __init abituguru3_init(void)
 			return err;
 
 #ifdef CONFIG_DMI
-		printk(KERN_WARNING ABIT_UGURU3_NAME ": this motherboard was "
-			"not detected using DMI. Please send the output of "
-			"\"dmidecode\" to the abituguru3 maintainer "
-			"(see MAINTAINERS)\n");
+		pr_warn("this motherboard was not detected using DMI. "
+			"Please send the output of \"dmidecode\" to the abituguru3 maintainer (see MAINTAINERS)\n");
 #endif
 	}
 
@@ -1233,8 +1229,7 @@ static int __init abituguru3_init(void)
 	abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME,
 						ABIT_UGURU3_BASE);
 	if (!abituguru3_pdev) {
-		printk(KERN_ERR ABIT_UGURU3_NAME
-			": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		err = -ENOMEM;
 		goto exit_driver_unregister;
 	}
@@ -1245,15 +1240,13 @@ static int __init abituguru3_init(void)
 
 	err = platform_device_add_resources(abituguru3_pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR ABIT_UGURU3_NAME
-			": Device resource addition failed (%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(abituguru3_pdev);
 	if (err) {
-		printk(KERN_ERR ABIT_UGURU3_NAME
-			": Device addition failed (%d)\n", err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 

drivers/hwmon/adt7470.c

@@ -19,6 +19,8 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/jiffies.h>
 #include <linux/i2c.h>
@@ -274,7 +276,7 @@ static int adt7470_read_temperatures(struct i2c_client *client,
 	i2c_smbus_write_byte_data(client, ADT7470_REG_PWM_CFG(2), pwm_cfg[1]);
 
 	if (res) {
-		printk(KERN_ERR "ha ha, interrupted");
+		pr_err("ha ha, interrupted\n");
 		return -EAGAIN;
 	}
 

drivers/hwmon/asb100.c

@@ -36,6 +36,8 @@
     asb100	7	3	1	4	0x31	0x0694	yes	no
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/i2c.h>
@@ -701,8 +703,7 @@ static int asb100_detect(struct i2c_client *client,
 	int val1, val2;
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
-		pr_debug("asb100.o: detect failed, "
-				"smbus byte data not supported!\n");
+		pr_debug("detect failed, smbus byte data not supported!\n");
 		return -ENODEV;
 	}
 
@@ -715,7 +716,7 @@ static int asb100_detect(struct i2c_client *client,
 			(((!(val1 & 0x80)) && (val2 != 0x94)) ||
 			/* Check for ASB100 ID (high byte ) */
 			((val1 & 0x80) && (val2 != 0x06)))) {
-		pr_debug("asb100: detect failed, bad chip id 0x%02x!\n", val2);
+		pr_debug("detect failed, bad chip id 0x%02x!\n", val2);
 		return -ENODEV;
 	}
 
@@ -744,7 +745,7 @@ static int asb100_probe(struct i2c_client *client,
 
 	data = kzalloc(sizeof(struct asb100_data), GFP_KERNEL);
 	if (!data) {
-		pr_debug("asb100.o: probe failed, kzalloc failed!\n");
+		pr_debug("probe failed, kzalloc failed!\n");
 		err = -ENOMEM;
 		goto ERROR0;
 	}

drivers/hwmon/asus_atk0110.c

@@ -5,6 +5,8 @@
  * See COPYING in the top level directory of the kernel tree.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/debugfs.h>
 #include <linux/kernel.h>
 #include <linux/hwmon.h>
@@ -1414,14 +1416,13 @@ static int __init atk0110_init(void)
 
 	/* Make sure it's safe to access the device through ACPI */
 	if (!acpi_resources_are_enforced()) {
-		pr_err("atk: Resources not safely usable due to "
-		       "acpi_enforce_resources kernel parameter\n");
+		pr_err("Resources not safely usable due to acpi_enforce_resources kernel parameter\n");
 		return -EBUSY;
 	}
 
 	ret = acpi_bus_register_driver(&atk_driver);
 	if (ret)
-		pr_info("atk: acpi_bus_register_driver failed: %d\n", ret);
+		pr_info("acpi_bus_register_driver failed: %d\n", ret);
 
 	return ret;
 }

drivers/hwmon/coretemp.c

@@ -20,6 +20,8 @@
  * 02110-1301 USA.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -445,8 +447,8 @@ static int __cpuinit coretemp_device_add(unsigned int cpu)
 	 * without thermal sensors will be filtered out.
 	 */
 	if (!cpu_has(c, X86_FEATURE_DTS)) {
-		printk(KERN_INFO DRVNAME ": CPU (model=0x%x)"
-		       " has no thermal sensor.\n", c->x86_model);
+		pr_info("CPU (model=0x%x) has no thermal sensor\n",
+			c->x86_model);
 		return 0;
 	}
 
@@ -466,7 +468,7 @@ static int __cpuinit coretemp_device_add(unsigned int cpu)
 	pdev = platform_device_alloc(DRVNAME, cpu);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
@@ -478,8 +480,7 @@ static int __cpuinit coretemp_device_add(unsigned int cpu)
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_free;
 	}
 

drivers/hwmon/dme1737.c

@@ -25,6 +25,8 @@
  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -2446,7 +2448,7 @@ static int __init dme1737_isa_detect(int sio_cip, unsigned short *addr)
 	/* Get the base address of the runtime registers */
 	if (!(base_addr = (dme1737_sio_inb(sio_cip, 0x60) << 8) |
 			   dme1737_sio_inb(sio_cip, 0x61))) {
-		printk(KERN_ERR "dme1737: Base address not set.\n");
+		pr_err("Base address not set\n");
 		err = -ENODEV;
 		goto exit;
 	}
@@ -2475,20 +2477,18 @@ static int __init dme1737_isa_device_add(unsigned short addr)
 		goto exit;
 
 	if (!(pdev = platform_device_alloc("dme1737", addr))) {
-		printk(KERN_ERR "dme1737: Failed to allocate device.\n");
+		pr_err("Failed to allocate device\n");
 		err = -ENOMEM;
 		goto exit;
 	}
 
 	if ((err = platform_device_add_resources(pdev, &res, 1))) {
-		printk(KERN_ERR "dme1737: Failed to add device resource "
-		       "(err = %d).\n", err);
+		pr_err("Failed to add device resource (err = %d)\n", err);
 		goto exit_device_put;
 	}
 
 	if ((err = platform_device_add(pdev))) {
-		printk(KERN_ERR "dme1737: Failed to add device (err = %d).\n",
-		       err);
+		pr_err("Failed to add device (err = %d)\n", err);
 		goto exit_device_put;
 	}
 

drivers/hwmon/ds620.c

+/*
+ *  ds620.c - Support for temperature sensor and thermostat DS620
+ *
+ *  Copyright (C) 2010, 2011 Roland Stigge <stigge@antcom.de>
+ *
+ *  based on ds1621.c by Christian W. Zuckschwerdt  <zany@triq.net>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+#include <linux/i2c/ds620.h>
+
+/*
+ * Many DS620 constants specified below
+ *  15   14   13   12   11   10   09    08
+ * |Done|NVB |THF |TLF |R1  |R0  |AUTOC|1SHOT|
+ *
+ *  07   06   05   04   03   02   01    00
+ * |PO2 |PO1 |A2  |A1  |A0  |    |     |     |
+ */
+#define DS620_REG_CONFIG_DONE		0x8000
+#define DS620_REG_CONFIG_NVB		0x4000
+#define DS620_REG_CONFIG_THF		0x2000
+#define DS620_REG_CONFIG_TLF		0x1000
+#define DS620_REG_CONFIG_R1		0x0800
+#define DS620_REG_CONFIG_R0		0x0400
+#define DS620_REG_CONFIG_AUTOC		0x0200
+#define DS620_REG_CONFIG_1SHOT		0x0100
+#define DS620_REG_CONFIG_PO2		0x0080
+#define DS620_REG_CONFIG_PO1		0x0040
+#define DS620_REG_CONFIG_A2		0x0020
+#define DS620_REG_CONFIG_A1		0x0010
+#define DS620_REG_CONFIG_A0		0x0008
+
+/* The DS620 registers */
+static const u8 DS620_REG_TEMP[3] = {
+	0xAA,			/* input, word, RO */
+	0xA2,			/* min, word, RW */
+	0xA0,			/* max, word, RW */
+};
+
+#define DS620_REG_CONF		0xAC	/* word, RW */
+#define DS620_COM_START		0x51	/* no data */
+#define DS620_COM_STOP		0x22	/* no data */
+
+/* Each client has this additional data */
+struct ds620_data {
+	struct device *hwmon_dev;
+	struct mutex update_lock;
+	char valid;		/* !=0 if following fields are valid */
+	unsigned long last_updated;	/* In jiffies */
+
+	u16 temp[3];		/* Register values, word */
+};
+
+/*
+ *  Temperature registers are word-sized.
+ *  DS620 uses a high-byte first convention, which is exactly opposite to
+ *  the SMBus standard.
+ */
+static int ds620_read_temp(struct i2c_client *client, u8 reg)
+{
+	int ret;
+
+	ret = i2c_smbus_read_word_data(client, reg);
+	if (ret < 0)
+		return ret;
+	return swab16(ret);
+}
+
+static int ds620_write_temp(struct i2c_client *client, u8 reg, u16 value)
+{
+	return i2c_smbus_write_word_data(client, reg, swab16(value));
+}
+
+static void ds620_init_client(struct i2c_client *client)
+{
+	struct ds620_platform_data *ds620_info = client->dev.platform_data;
+	u16 conf, new_conf;
+
+	new_conf = conf =
+	    swab16(i2c_smbus_read_word_data(client, DS620_REG_CONF));
+
+	/* switch to continuous conversion mode */
+	new_conf &= ~DS620_REG_CONFIG_1SHOT;
+	/* already high at power-on, but don't trust the BIOS! */
+	new_conf |= DS620_REG_CONFIG_PO2;
+	/* thermostat mode according to platform data */
+	if (ds620_info && ds620_info->pomode == 1)
+		new_conf &= ~DS620_REG_CONFIG_PO1; /* PO_LOW */
+	else if (ds620_info && ds620_info->pomode == 2)
+		new_conf |= DS620_REG_CONFIG_PO1; /* PO_HIGH */
+	else
+		new_conf &= ~DS620_REG_CONFIG_PO2; /* always low */
+	/* with highest precision */
+	new_conf |= DS620_REG_CONFIG_R1 | DS620_REG_CONFIG_R0;
+
+	if (conf != new_conf)
+		i2c_smbus_write_word_data(client, DS620_REG_CONF,
+					  swab16(new_conf));
+
+	/* start conversion */
+	i2c_smbus_write_byte(client, DS620_COM_START);
+}
+
+static struct ds620_data *ds620_update_client(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct ds620_data *data = i2c_get_clientdata(client);
+	struct ds620_data *ret = data;
+
+	mutex_lock(&data->update_lock);
+
+	if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
+	    || !data->valid) {
+		int i;
+		int res;
+
+		dev_dbg(&client->dev, "Starting ds620 update\n");
+
+		for (i = 0; i < ARRAY_SIZE(data->temp); i++) {
+			res = ds620_read_temp(client,
+					      DS620_REG_TEMP[i]);
+			if (res < 0) {
+				ret = ERR_PTR(res);
+				goto abort;
+			}
+
+			data->temp[i] = res;
+		}
+
+		data->last_updated = jiffies;
+		data->valid = 1;
+	}
+abort:
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+static ssize_t show_temp(struct device *dev, struct device_attribute *da,
+			 char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	struct ds620_data *data = ds620_update_client(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return sprintf(buf, "%d\n", ((data->temp[attr->index] / 8) * 625) / 10);
+}
+
+static ssize_t set_temp(struct device *dev, struct device_attribute *da,
+			const char *buf, size_t count)
+{
+	int res;
+	long val;
+
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	struct i2c_client *client = to_i2c_client(dev);
+	struct ds620_data *data = i2c_get_clientdata(client);
+
+	res = strict_strtol(buf, 10, &val);
+
+	if (res)
+		return res;
+
+	val = (val * 10 / 625) * 8;
+
+	mutex_lock(&data->update_lock);
+	data->temp[attr->index] = val;
+	ds620_write_temp(client, DS620_REG_TEMP[attr->index],
+			 data->temp[attr->index]);
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+static ssize_t show_alarm(struct device *dev, struct device_attribute *da,
+			  char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	struct ds620_data *data = ds620_update_client(dev);
+	struct i2c_client *client = to_i2c_client(dev);
+	u16 conf, new_conf;
+	int res;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	/* reset alarms if necessary */
+	res = i2c_smbus_read_word_data(client, DS620_REG_CONF);
+	if (res < 0)
+		return res;
+
+	conf = swab16(res);
+	new_conf = conf;
+	new_conf &= ~attr->index;
+	if (conf != new_conf) {
+		res = i2c_smbus_write_word_data(client, DS620_REG_CONF,
+						swab16(new_conf));
+		if (res < 0)
+			return res;
+	}
+
+	return sprintf(buf, "%d\n", !!(conf & attr->index));
+}
+
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp, set_temp, 1);
+static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp, set_temp, 2);
+static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL,
+			  DS620_REG_CONFIG_TLF);
+static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL,
+			  DS620_REG_CONFIG_THF);
+
+static struct attribute *ds620_attributes[] = {
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_min.dev_attr.attr,
+	&sensor_dev_attr_temp1_max.dev_attr.attr,
+	&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
+	&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group ds620_group = {
+	.attrs = ds620_attributes,
+};
+
+static int ds620_probe(struct i2c_client *client,
+		       const struct i2c_device_id *id)
+{
+	struct ds620_data *data;
+	int err;
+
+	data = kzalloc(sizeof(struct ds620_data), GFP_KERNEL);
+	if (!data) {
+		err = -ENOMEM;
+		goto exit;
+	}
+
+	i2c_set_clientdata(client, data);
+	mutex_init(&data->update_lock);
+
+	/* Initialize the DS620 chip */
+	ds620_init_client(client);
+
+	/* Register sysfs hooks */
+	err = sysfs_create_group(&client->dev.kobj, &ds620_group);
+	if (err)
+		goto exit_free;
+
+	data->hwmon_dev = hwmon_device_register(&client->dev);
+	if (IS_ERR(data->hwmon_dev)) {
+		err = PTR_ERR(data->hwmon_dev);
+		goto exit_remove_files;
+	}
+
+	dev_info(&client->dev, "temperature sensor found\n");
+
+	return 0;
+
+exit_remove_files:
+	sysfs_remove_group(&client->dev.kobj, &ds620_group);
+exit_free:
+	kfree(data);
+exit:
+	return err;
+}
+
+static int ds620_remove(struct i2c_client *client)
+{
+	struct ds620_data *data = i2c_get_clientdata(client);
+
+	hwmon_device_unregister(data->hwmon_dev);
+	sysfs_remove_group(&client->dev.kobj, &ds620_group);
+
+	kfree(data);
+
+	return 0;
+}
+
+static const struct i2c_device_id ds620_id[] = {
+	{"ds620", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, ds620_id);
+
+/* This is the driver that will be inserted */
+static struct i2c_driver ds620_driver = {
+	.class = I2C_CLASS_HWMON,
+	.driver = {
+		   .name = "ds620",
+	},
+	.probe = ds620_probe,
+	.remove = ds620_remove,
+	.id_table = ds620_id,
+};
+
+static int __init ds620_init(void)
+{
+	return i2c_add_driver(&ds620_driver);
+}
+
+static void __exit ds620_exit(void)
+{
+	i2c_del_driver(&ds620_driver);
+}
+
+MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>");
+MODULE_DESCRIPTION("DS620 driver");
+MODULE_LICENSE("GPL");
+
+module_init(ds620_init);
+module_exit(ds620_exit);

drivers/hwmon/f71805f.c

@@ -28,6 +28,8 @@
  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -1309,7 +1311,7 @@ static int __devinit f71805f_probe(struct platform_device *pdev)
 
 	if (!(data = kzalloc(sizeof(struct f71805f_data), GFP_KERNEL))) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Out of memory\n");
+		pr_err("Out of memory\n");
 		goto exit;
 	}
 
@@ -1451,7 +1453,7 @@ static int __init f71805f_device_add(unsigned short address,
 	pdev = platform_device_alloc(DRVNAME, address);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
@@ -1462,22 +1464,20 @@ static int __init f71805f_device_add(unsigned short address,
 
 	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device resource addition failed "
-		       "(%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	err = platform_device_add_data(pdev, sio_data,
 				       sizeof(struct f71805f_sio_data));
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
+		pr_err("Platform data allocation failed\n");
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
@@ -1516,30 +1516,27 @@ static int __init f71805f_find(int sioaddr, unsigned short *address,
 		sio_data->fnsel1 = superio_inb(sioaddr, SIO_REG_FNSEL1);
 		break;
 	default:
-		printk(KERN_INFO DRVNAME ": Unsupported Fintek device, "
-		       "skipping\n");
+		pr_info("Unsupported Fintek device, skipping\n");
 		goto exit;
 	}
 
 	superio_select(sioaddr, F71805F_LD_HWM);
 	if (!(superio_inb(sioaddr, SIO_REG_ENABLE) & 0x01)) {
-		printk(KERN_WARNING DRVNAME ": Device not activated, "
-		       "skipping\n");
+		pr_warn("Device not activated, skipping\n");
 		goto exit;
 	}
 
 	*address = superio_inw(sioaddr, SIO_REG_ADDR);
 	if (*address == 0) {
-		printk(KERN_WARNING DRVNAME ": Base address not set, "
-		       "skipping\n");
+		pr_warn("Base address not set, skipping\n");
 		goto exit;
 	}
 	*address &= ~(REGION_LENGTH - 1);	/* Ignore 3 LSB */
 
 	err = 0;
-	printk(KERN_INFO DRVNAME ": Found %s chip at %#x, revision %u\n",
-	       names[sio_data->kind], *address,
-	       superio_inb(sioaddr, SIO_REG_DEVREV));
+	pr_info("Found %s chip at %#x, revision %u\n",
+		names[sio_data->kind], *address,
+		superio_inb(sioaddr, SIO_REG_DEVREV));
 
 exit:
 	superio_exit(sioaddr);

drivers/hwmon/f71882fg.c

@@ -18,6 +18,8 @@
  *   59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.             *
  ***************************************************************************/
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -865,8 +867,7 @@ static inline int superio_enter(int base)
 {
 	/* Don't step on other drivers' I/O space by accident */
 	if (!request_muxed_region(base, 2, DRVNAME)) {
-		printk(KERN_ERR DRVNAME ": I/O address 0x%04x already in use\n",
-				base);
+		pr_err("I/O address 0x%04x already in use\n", base);
 		return -EBUSY;
 	}
 
@@ -2192,7 +2193,7 @@ static int __init f71882fg_find(int sioaddr, unsigned short *address,
 
 	devid = superio_inw(sioaddr, SIO_REG_MANID);
 	if (devid != SIO_FINTEK_ID) {
-		pr_debug(DRVNAME ": Not a Fintek device\n");
+		pr_debug("Not a Fintek device\n");
 		err = -ENODEV;
 		goto exit;
 	}
@@ -2215,8 +2216,8 @@ static int __init f71882fg_find(int sioaddr, unsigned short *address,
 		sio_data->type = f8000;
 		break;
 	default:
-		printk(KERN_INFO DRVNAME ": Unsupported Fintek device: %04x\n",
-		       (unsigned int)devid);
+		pr_info("Unsupported Fintek device: %04x\n",
+			(unsigned int)devid);
 		err = -ENODEV;
 		goto exit;
 	}
@@ -2227,21 +2228,21 @@ static int __init f71882fg_find(int sioaddr, unsigned short *address,
 		superio_select(sioaddr, SIO_F71882FG_LD_HWM);
 
 	if (!(superio_inb(sioaddr, SIO_REG_ENABLE) & 0x01)) {
-		printk(KERN_WARNING DRVNAME ": Device not activated\n");
+		pr_warn("Device not activated\n");
 		err = -ENODEV;
 		goto exit;
 	}
 
 	*address = superio_inw(sioaddr, SIO_REG_ADDR);
 	if (*address == 0) {
-		printk(KERN_WARNING DRVNAME ": Base address not set\n");
+		pr_warn("Base address not set\n");
 		err = -ENODEV;
 		goto exit;
 	}
 	*address &= ~(REGION_LENGTH - 1);	/* Ignore 3 LSB */
 
 	err = 0;
-	printk(KERN_INFO DRVNAME ": Found %s chip at %#x, revision %d\n",
+	pr_info("Found %s chip at %#x, revision %d\n",
 		f71882fg_names[sio_data->type],	(unsigned int)*address,
 		(int)superio_inb(sioaddr, SIO_REG_DEVREV));
 exit:
@@ -2270,20 +2271,20 @@ static int __init f71882fg_device_add(unsigned short address,
 
 	err = platform_device_add_resources(f71882fg_pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device resource addition failed\n");
+		pr_err("Device resource addition failed\n");
 		goto exit_device_put;
 	}
 
 	err = platform_device_add_data(f71882fg_pdev, sio_data,
 				       sizeof(struct f71882fg_sio_data));
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
+		pr_err("Platform data allocation failed\n");
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(f71882fg_pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed\n");
+		pr_err("Device addition failed\n");
 		goto exit_device_put;
 	}
 

drivers/hwmon/hp_accel.c

@@ -20,6 +20,8 @@
  *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/dmi.h>
@@ -147,7 +149,7 @@ int lis3lv02d_acpi_write(struct lis3lv02d *lis3, int reg, u8 val)
 static int lis3lv02d_dmi_matched(const struct dmi_system_id *dmi)
 {
 	lis3_dev.ac = *((union axis_conversion *)dmi->driver_data);
-	printk(KERN_INFO DRIVER_NAME ": hardware type %s found.\n", dmi->ident);
+	pr_info("hardware type %s found\n", dmi->ident);
 
 	return 1;
 }
@@ -303,11 +305,10 @@ static int lis3lv02d_add(struct acpi_device *device)
 
 	/* If possible use a "standard" axes order */
 	if (lis3_dev.ac.x && lis3_dev.ac.y && lis3_dev.ac.z) {
-		printk(KERN_INFO DRIVER_NAME ": Using custom axes %d,%d,%d\n",
-		       lis3_dev.ac.x, lis3_dev.ac.y, lis3_dev.ac.z);
+		pr_info("Using custom axes %d,%d,%d\n",
+			lis3_dev.ac.x, lis3_dev.ac.y, lis3_dev.ac.z);
 	} else if (dmi_check_system(lis3lv02d_dmi_ids) == 0) {
-		printk(KERN_INFO DRIVER_NAME ": laptop model unknown, "
-				 "using default axes configuration\n");
+		pr_info("laptop model unknown, using default axes configuration\n");
 		lis3_dev.ac = lis3lv02d_axis_normal;
 	}
 
@@ -385,7 +386,7 @@ static int __init lis3lv02d_init_module(void)
 	if (ret < 0)
 		return ret;
 
-	printk(KERN_INFO DRIVER_NAME " driver loaded.\n");
+	pr_info("driver loaded\n");
 
 	return 0;
 }

drivers/hwmon/hwmon-vid.c

@@ -22,6 +22,8 @@
  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/hwmon-vid.h>
@@ -146,8 +148,8 @@ int vid_from_reg(int val, u8 vrm)
 		return(val > 0x77 ? 0 : (1500000 - (val * 12500) + 500) / 1000);
 	default:		/* report 0 for unknown */
 		if (vrm)
-			printk(KERN_WARNING "hwmon-vid: Requested unsupported "
-			       "VRM version (%u)\n", (unsigned int)vrm);
+			pr_warn("Requested unsupported VRM version (%u)\n",
+				(unsigned int)vrm);
 		return 0;
 	}
 }
@@ -246,8 +248,7 @@ u8 vid_which_vrm(void)
 	}
 	vrm_ret = find_vrm(eff_family, eff_model, eff_stepping, c->x86_vendor);
 	if (vrm_ret == 0)
-		printk(KERN_INFO "hwmon-vid: Unknown VRM version of your "
-		       "x86 CPU\n");
+		pr_info("Unknown VRM version of your x86 CPU\n");
 	return vrm_ret;
 }
 
@@ -255,7 +256,7 @@ u8 vid_which_vrm(void)
 #else
 u8 vid_which_vrm(void)
 {
-	printk(KERN_INFO "hwmon-vid: Unknown VRM version of your CPU\n");
+	pr_info("Unknown VRM version of your CPU\n");
 	return 0;
 }
 #endif

drivers/hwmon/hwmon.c

@@ -10,6 +10,8 @@
     the Free Software Foundation; version 2 of the License.
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/device.h>
 #include <linux/err.h>
@@ -119,7 +121,7 @@ static int __init hwmon_init(void)
 
 	hwmon_class = class_create(THIS_MODULE, "hwmon");
 	if (IS_ERR(hwmon_class)) {
-		printk(KERN_ERR "hwmon.c: couldn't create sysfs class\n");
+		pr_err("couldn't create sysfs class\n");
 		return PTR_ERR(hwmon_class);
 	}
 	return 0;

drivers/hwmon/ibmaem.c

@@ -20,6 +20,8 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/ipmi.h>
 #include <linux/module.h>
 #include <linux/hwmon.h>
@@ -1090,7 +1092,7 @@ static int __init aem_init(void)
 
 	res = driver_register(&aem_driver.driver);
 	if (res) {
-		printk(KERN_ERR "Can't register aem driver\n");
+		pr_err("Can't register aem driver\n");
 		return res;
 	}
 

drivers/hwmon/lis3lv02d.c

@@ -20,6 +20,8 @@
  *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/dmi.h>
@@ -860,8 +862,7 @@ static void lis3lv02d_8b_configure(struct lis3lv02d *dev,
 					(p->irq_flags2 & IRQF_TRIGGER_MASK),
 					DRIVER_NAME, &lis3_dev);
 		if (err < 0)
-			printk(KERN_ERR DRIVER_NAME
-				"No second IRQ. Limited functionality\n");
+			pr_err("No second IRQ. Limited functionality\n");
 	}
 }
 
@@ -879,7 +880,7 @@ int lis3lv02d_init_device(struct lis3lv02d *dev)
 
 	switch (dev->whoami) {
 	case WAI_12B:
-		printk(KERN_INFO DRIVER_NAME ": 12 bits sensor found\n");
+		pr_info("12 bits sensor found\n");
 		dev->read_data = lis3lv02d_read_12;
 		dev->mdps_max_val = 2048;
 		dev->pwron_delay = LIS3_PWRON_DELAY_WAI_12B;
@@ -890,7 +891,7 @@ int lis3lv02d_init_device(struct lis3lv02d *dev)
 		dev->regs_size = ARRAY_SIZE(lis3_wai12_regs);
 		break;
 	case WAI_8B:
-		printk(KERN_INFO DRIVER_NAME ": 8 bits sensor found\n");
+		pr_info("8 bits sensor found\n");
 		dev->read_data = lis3lv02d_read_8;
 		dev->mdps_max_val = 128;
 		dev->pwron_delay = LIS3_PWRON_DELAY_WAI_8B;
@@ -901,7 +902,7 @@ int lis3lv02d_init_device(struct lis3lv02d *dev)
 		dev->regs_size = ARRAY_SIZE(lis3_wai8_regs);
 		break;
 	case WAI_3DC:
-		printk(KERN_INFO DRIVER_NAME ": 8 bits 3DC sensor found\n");
+		pr_info("8 bits 3DC sensor found\n");
 		dev->read_data = lis3lv02d_read_8;
 		dev->mdps_max_val = 128;
 		dev->pwron_delay = LIS3_PWRON_DELAY_WAI_8B;
@@ -910,8 +911,7 @@ int lis3lv02d_init_device(struct lis3lv02d *dev)
 		dev->scale = LIS3_SENSITIVITY_8B;
 		break;
 	default:
-		printk(KERN_ERR DRIVER_NAME
-			": unknown sensor type 0x%X\n", dev->whoami);
+		pr_err("unknown sensor type 0x%X\n", dev->whoami);
 		return -EINVAL;
 	}
 
@@ -935,7 +935,7 @@ int lis3lv02d_init_device(struct lis3lv02d *dev)
 	}
 
 	if (lis3lv02d_joystick_enable())
-		printk(KERN_ERR DRIVER_NAME ": joystick initialization failed\n");
+		pr_err("joystick initialization failed\n");
 
 	/* passing in platform specific data is purely optional and only
 	 * used by the SPI transport layer at the moment */
@@ -957,8 +957,7 @@ int lis3lv02d_init_device(struct lis3lv02d *dev)
 
 	/* bail if we did not get an IRQ from the bus layer */
 	if (!dev->irq) {
-		printk(KERN_ERR DRIVER_NAME
-			": No IRQ. Disabling /dev/freefall\n");
+		pr_err("No IRQ. Disabling /dev/freefall\n");
 		goto out;
 	}
 
@@ -985,12 +984,12 @@ int lis3lv02d_init_device(struct lis3lv02d *dev)
 				DRIVER_NAME, &lis3_dev);
 
 	if (err < 0) {
-		printk(KERN_ERR DRIVER_NAME "Cannot get IRQ\n");
+		pr_err("Cannot get IRQ\n");
 		goto out;
 	}
 
 	if (misc_register(&lis3lv02d_misc_device))
-		printk(KERN_ERR DRIVER_NAME ": misc_register failed\n");
+		pr_err("misc_register failed\n");
 out:
 	return 0;
 }

drivers/hwmon/lm70.c

@@ -24,6 +24,8 @@
  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
@@ -67,8 +69,7 @@ static ssize_t lm70_sense_temp(struct device *dev,
 	 */
 	status = spi_write_then_read(spi, NULL, 0, &rxbuf[0], 2);
 	if (status < 0) {
-		printk(KERN_WARNING
-		"spi_write_then_read failed with status %d\n", status);
+		pr_warn("spi_write_then_read failed with status %d\n", status);
 		goto out;
 	}
 	raw = (rxbuf[0] << 8) + rxbuf[1];

drivers/hwmon/pcf8591.c

@@ -18,6 +18,8 @@
     Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -290,8 +292,7 @@ static struct i2c_driver pcf8591_driver = {
 static int __init pcf8591_init(void)
 {
 	if (input_mode < 0 || input_mode > 3) {
-		printk(KERN_WARNING "pcf8591: invalid input_mode (%d)\n",
-		       input_mode);
+		pr_warn("invalid input_mode (%d)\n", input_mode);
 		input_mode = 0;
 	}
 	return i2c_add_driver(&pcf8591_driver);

drivers/hwmon/pkgtemp.c

@@ -20,6 +20,8 @@
  * 02110-1301 USA.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -303,7 +305,7 @@ static int __cpuinit pkgtemp_device_add(unsigned int cpu)
 	pdev = platform_device_alloc(DRVNAME, cpu);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
@@ -315,8 +317,7 @@ static int __cpuinit pkgtemp_device_add(unsigned int cpu)
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_free;
 	}
 

drivers/hwmon/sht21.c

+/* Sensirion SHT21 humidity and temperature sensor driver
+ *
+ * Copyright (C) 2010 Urs Fleisch <urs.fleisch@sensirion.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA
+ *
+ * Data sheet available (5/2010) at
+ * http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT21.pdf
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/device.h>
+
+/* I2C command bytes */
+#define SHT21_TRIG_T_MEASUREMENT_HM  0xe3
+#define SHT21_TRIG_RH_MEASUREMENT_HM 0xe5
+
+/**
+ * struct sht21 - SHT21 device specific data
+ * @hwmon_dev: device registered with hwmon
+ * @lock: mutex to protect measurement values
+ * @valid: only 0 before first measurement is taken
+ * @last_update: time of last update (jiffies)
+ * @temperature: cached temperature measurement value
+ * @humidity: cached humidity measurement value
+ */
+struct sht21 {
+	struct device *hwmon_dev;
+	struct mutex lock;
+	char valid;
+	unsigned long last_update;
+	int temperature;
+	int humidity;
+};
+
+/**
+ * sht21_temp_ticks_to_millicelsius() - convert raw temperature ticks to
+ * milli celsius
+ * @ticks: temperature ticks value received from sensor
+ */
+static inline int sht21_temp_ticks_to_millicelsius(int ticks)
+{
+	ticks &= ~0x0003; /* clear status bits */
+	/*
+	 * Formula T = -46.85 + 175.72 * ST / 2^16 from data sheet 6.2,
+	 * optimized for integer fixed point (3 digits) arithmetic
+	 */
+	return ((21965 * ticks) >> 13) - 46850;
+}
+
+/**
+ * sht21_rh_ticks_to_per_cent_mille() - convert raw humidity ticks to
+ * one-thousandths of a percent relative humidity
+ * @ticks: humidity ticks value received from sensor
+ */
+static inline int sht21_rh_ticks_to_per_cent_mille(int ticks)
+{
+	ticks &= ~0x0003; /* clear status bits */
+	/*
+	 * Formula RH = -6 + 125 * SRH / 2^16 from data sheet 6.1,
+	 * optimized for integer fixed point (3 digits) arithmetic
+	 */
+	return ((15625 * ticks) >> 13) - 6000;
+}
+
+/**
+ * sht21_read_word_data() - read word from register
+ * @client: I2C client device
+ * @reg: I2C command byte
+ *
+ * Returns value, negative errno on error.
+ */
+static inline int sht21_read_word_data(struct i2c_client *client, u8 reg)
+{
+	int ret = i2c_smbus_read_word_data(client, reg);
+	if (ret < 0)
+		return ret;
+	/*
+	 * SMBus specifies low byte first, but the SHT21 returns MSB
+	 * first, so we have to swab16 the values
+	 */
+	return swab16(ret);
+}
+
+/**
+ * sht21_update_measurements() - get updated measurements from device
+ * @client: I2C client device
+ *
+ * Returns 0 on success, else negative errno.
+ */
+static int sht21_update_measurements(struct i2c_client *client)
+{
+	int ret = 0;
+	struct sht21 *sht21 = i2c_get_clientdata(client);
+
+	mutex_lock(&sht21->lock);
+	/*
+	 * Data sheet 2.4:
+	 * SHT2x should not be active for more than 10% of the time - e.g.
+	 * maximum two measurements per second at 12bit accuracy shall be made.
+	 */
+	if (time_after(jiffies, sht21->last_update + HZ / 2) || !sht21->valid) {
+		ret = sht21_read_word_data(client, SHT21_TRIG_T_MEASUREMENT_HM);
+		if (ret < 0)
+			goto out;
+		sht21->temperature = sht21_temp_ticks_to_millicelsius(ret);
+		ret = sht21_read_word_data(client,
+					SHT21_TRIG_RH_MEASUREMENT_HM);
+		if (ret < 0)
+			goto out;
+		sht21->humidity = sht21_rh_ticks_to_per_cent_mille(ret);
+		sht21->last_update = jiffies;
+		sht21->valid = 1;
+	}
+out:
+	mutex_unlock(&sht21->lock);
+
+	return ret >= 0 ? 0 : ret;
+}
+
+/**
+ * sht21_show_temperature() - show temperature measurement value in sysfs
+ * @dev: device
+ * @attr: device attribute
+ * @buf: sysfs buffer (PAGE_SIZE) where measurement values are written to
+ *
+ * Will be called on read access to temp1_input sysfs attribute.
+ * Returns number of bytes written into buffer, negative errno on error.
+ */
+static ssize_t sht21_show_temperature(struct device *dev,
+	struct device_attribute *attr,
+	char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct sht21 *sht21 = i2c_get_clientdata(client);
+	int ret = sht21_update_measurements(client);
+	if (ret < 0)
+		return ret;
+	return sprintf(buf, "%d\n", sht21->temperature);
+}
+
+/**
+ * sht21_show_humidity() - show humidity measurement value in sysfs
+ * @dev: device
+ * @attr: device attribute
+ * @buf: sysfs buffer (PAGE_SIZE) where measurement values are written to
+ *
+ * Will be called on read access to humidity1_input sysfs attribute.
+ * Returns number of bytes written into buffer, negative errno on error.
+ */
+static ssize_t sht21_show_humidity(struct device *dev,
+	struct device_attribute *attr,
+	char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct sht21 *sht21 = i2c_get_clientdata(client);
+	int ret = sht21_update_measurements(client);
+	if (ret < 0)
+		return ret;
+	return sprintf(buf, "%d\n", sht21->humidity);
+}
+
+/* sysfs attributes */
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, sht21_show_temperature,
+	NULL, 0);
+static SENSOR_DEVICE_ATTR(humidity1_input, S_IRUGO, sht21_show_humidity,
+	NULL, 0);
+
+static struct attribute *sht21_attributes[] = {
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_humidity1_input.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group sht21_attr_group = {
+	.attrs = sht21_attributes,
+};
+
+/**
+ * sht21_probe() - probe device
+ * @client: I2C client device
+ * @id: device ID
+ *
+ * Called by the I2C core when an entry in the ID table matches a
+ * device's name.
+ * Returns 0 on success.
+ */
+static int __devinit sht21_probe(struct i2c_client *client,
+	const struct i2c_device_id *id)
+{
+	struct sht21 *sht21;
+	int err;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_WORD_DATA)) {
+		dev_err(&client->dev,
+			"adapter does not support SMBus word transactions\n");
+		return -ENODEV;
+	}
+
+	sht21 = kzalloc(sizeof(*sht21), GFP_KERNEL);
+	if (!sht21) {
+		dev_dbg(&client->dev, "kzalloc failed\n");
+		return -ENOMEM;
+	}
+	i2c_set_clientdata(client, sht21);
+
+	mutex_init(&sht21->lock);
+
+	err = sysfs_create_group(&client->dev.kobj, &sht21_attr_group);
+	if (err) {
+		dev_dbg(&client->dev, "could not create sysfs files\n");
+		goto fail_free;
+	}
+	sht21->hwmon_dev = hwmon_device_register(&client->dev);
+	if (IS_ERR(sht21->hwmon_dev)) {
+		dev_dbg(&client->dev, "unable to register hwmon device\n");
+		err = PTR_ERR(sht21->hwmon_dev);
+		goto fail_remove_sysfs;
+	}
+
+	dev_info(&client->dev, "initialized\n");
+
+	return 0;
+
+fail_remove_sysfs:
+	sysfs_remove_group(&client->dev.kobj, &sht21_attr_group);
+fail_free:
+	kfree(sht21);
+
+	return err;
+}
+
+/**
+ * sht21_remove() - remove device
+ * @client: I2C client device
+ */
+static int __devexit sht21_remove(struct i2c_client *client)
+{
+	struct sht21 *sht21 = i2c_get_clientdata(client);
+
+	hwmon_device_unregister(sht21->hwmon_dev);
+	sysfs_remove_group(&client->dev.kobj, &sht21_attr_group);
+	kfree(sht21);
+
+	return 0;
+}
+
+/* Device ID table */
+static const struct i2c_device_id sht21_id[] = {
+	{ "sht21", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, sht21_id);
+
+static struct i2c_driver sht21_driver = {
+	.driver.name = "sht21",
+	.probe       = sht21_probe,
+	.remove      = __devexit_p(sht21_remove),
+	.id_table    = sht21_id,
+};
+
+/**
+ * sht21_init() - initialize driver
+ *
+ * Called when kernel is booted or module is inserted.
+ * Returns 0 on success.
+ */
+static int __init sht21_init(void)
+{
+	return i2c_add_driver(&sht21_driver);
+}
+module_init(sht21_init);
+
+/**
+ * sht21_init() - clean up driver
+ *
+ * Called when module is removed.
+ */
+static void __exit sht21_exit(void)
+{
+	i2c_del_driver(&sht21_driver);
+}
+module_exit(sht21_exit);
+
+MODULE_AUTHOR("Urs Fleisch <urs.fleisch@sensirion.com>");
+MODULE_DESCRIPTION("Sensirion SHT21 humidity and temperature sensor driver");
+MODULE_LICENSE("GPL");

drivers/hwmon/sis5595.c

@@ -50,6 +50,8 @@
 	 735		0008		0735
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/ioport.h>
@@ -735,21 +737,19 @@ static int __devinit sis5595_device_add(unsigned short address)
 	pdev = platform_device_alloc("sis5595", address);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR "sis5595: Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
 	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR "sis5595: Device resource addition failed "
-		       "(%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR "sis5595: Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 

drivers/hwmon/smsc47b397.c

@@ -26,6 +26,8 @@
     Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/ioport.h>
@@ -311,21 +313,19 @@ static int __init smsc47b397_device_add(unsigned short address)
 	pdev = platform_device_alloc(DRVNAME, address);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
 	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device resource addition failed "
-		       "(%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
@@ -367,8 +367,7 @@ static int __init smsc47b397_find(unsigned short *addr)
 	*addr = (superio_inb(SUPERIO_REG_BASE_MSB) << 8)
 		 |  superio_inb(SUPERIO_REG_BASE_LSB);
 
-	printk(KERN_INFO DRVNAME ": found SMSC %s "
-		"(base address 0x%04x, revision %u)\n",
+	pr_info("found SMSC %s (base address 0x%04x, revision %u)\n",
 		name, *addr, rev);
 
 	superio_exit();

drivers/hwmon/smsc47m1.c

@@ -26,6 +26,8 @@
     Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/ioport.h>
@@ -435,30 +437,29 @@ static int __init smsc47m1_find(unsigned short *addr,
 	 */
 	switch (val) {
 	case 0x51:
-		pr_info(DRVNAME ": Found SMSC LPC47B27x\n");
+		pr_info("Found SMSC LPC47B27x\n");
 		sio_data->type = smsc47m1;
 		break;
 	case 0x59:
-		pr_info(DRVNAME ": Found SMSC LPC47M10x/LPC47M112/LPC47M13x\n");
+		pr_info("Found SMSC LPC47M10x/LPC47M112/LPC47M13x\n");
 		sio_data->type = smsc47m1;
 		break;
 	case 0x5F:
-		pr_info(DRVNAME ": Found SMSC LPC47M14x\n");
+		pr_info("Found SMSC LPC47M14x\n");
 		sio_data->type = smsc47m1;
 		break;
 	case 0x60:
-		pr_info(DRVNAME ": Found SMSC LPC47M15x/LPC47M192/LPC47M997\n");
+		pr_info("Found SMSC LPC47M15x/LPC47M192/LPC47M997\n");
 		sio_data->type = smsc47m1;
 		break;
 	case 0x6B:
 		if (superio_inb(SUPERIO_REG_DEVREV) & 0x80) {
-			pr_debug(DRVNAME ": "
-				 "Found SMSC LPC47M233, unsupported\n");
+			pr_debug("Found SMSC LPC47M233, unsupported\n");
 			superio_exit();
 			return -ENODEV;
 		}
 
-		pr_info(DRVNAME ": Found SMSC LPC47M292\n");
+		pr_info("Found SMSC LPC47M292\n");
 		sio_data->type = smsc47m2;
 		break;
 	default:
@@ -470,7 +471,7 @@ static int __init smsc47m1_find(unsigned short *addr,
 	*addr = (superio_inb(SUPERIO_REG_BASE) << 8)
 	      |  superio_inb(SUPERIO_REG_BASE + 1);
 	if (*addr == 0) {
-		pr_info(DRVNAME ": Device address not set, will not use\n");
+		pr_info("Device address not set, will not use\n");
 		superio_exit();
 		return -ENODEV;
 	}
@@ -479,7 +480,7 @@ static int __init smsc47m1_find(unsigned short *addr,
 	 * Compaq Presario S4000NX) */
 	sio_data->activate = superio_inb(SUPERIO_REG_ACT);
 	if ((sio_data->activate & 0x01) == 0) {
-		pr_info(DRVNAME ": Enabling device\n");
+		pr_info("Enabling device\n");
 		superio_outb(SUPERIO_REG_ACT, sio_data->activate | 0x01);
 	}
 
@@ -494,7 +495,7 @@ static void smsc47m1_restore(const struct smsc47m1_sio_data *sio_data)
 		superio_enter();
 		superio_select();
 
-		pr_info(DRVNAME ": Disabling device\n");
+		pr_info("Disabling device\n");
 		superio_outb(SUPERIO_REG_ACT, sio_data->activate);
 
 		superio_exit();
@@ -823,28 +824,26 @@ static int __init smsc47m1_device_add(unsigned short address,
 	pdev = platform_device_alloc(DRVNAME, address);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
 	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device resource addition failed "
-		       "(%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	err = platform_device_add_data(pdev, sio_data,
 				       sizeof(struct smsc47m1_sio_data));
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
+		pr_err("Platform data allocation failed\n");
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 

drivers/hwmon/via-cputemp.c

@@ -21,6 +21,8 @@
  * 02110-1301 USA.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -202,7 +204,7 @@ static int __cpuinit via_cputemp_device_add(unsigned int cpu)
 	pdev = platform_device_alloc(DRVNAME, cpu);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
@@ -214,8 +216,7 @@ static int __cpuinit via_cputemp_device_add(unsigned int cpu)
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_free;
 	}
 
@@ -237,13 +238,16 @@ static int __cpuinit via_cputemp_device_add(unsigned int cpu)
 
 static void __cpuinit via_cputemp_device_remove(unsigned int cpu)
 {
-	struct pdev_entry *p, *n;
+	struct pdev_entry *p;
+
 	mutex_lock(&pdev_list_mutex);
-	list_for_each_entry_safe(p, n, &pdev_list, list) {
+	list_for_each_entry(p, &pdev_list, list) {
 		if (p->cpu == cpu) {
 			platform_device_unregister(p->pdev);
 			list_del(&p->list);
+			mutex_unlock(&pdev_list_mutex);
 			kfree(p);
+			return;
 		}
 	}
 	mutex_unlock(&pdev_list_mutex);
@@ -273,7 +277,6 @@ static struct notifier_block via_cputemp_cpu_notifier __refdata = {
 static int __init via_cputemp_init(void)
 {
 	int i, err;
-	struct pdev_entry *p, *n;
 
 	if (cpu_data(0).x86_vendor != X86_VENDOR_CENTAUR) {
 		printk(KERN_DEBUG DRVNAME ": Not a VIA CPU\n");
@@ -295,33 +298,27 @@ static int __init via_cputemp_init(void)
 			continue;
 
 		if (c->x86_model > 0x0f) {
-			printk(KERN_WARNING DRVNAME ": Unknown CPU "
-				"model 0x%x\n", c->x86_model);
+			pr_warn("Unknown CPU model 0x%x\n", c->x86_model);
 			continue;
 		}
 
-		err = via_cputemp_device_add(i);
-		if (err)
-			goto exit_devices_unreg;
+		via_cputemp_device_add(i);
 	}
+
+#ifndef CONFIG_HOTPLUG_CPU
 	if (list_empty(&pdev_list)) {
 		err = -ENODEV;
 		goto exit_driver_unreg;
 	}
+#endif
 
 	register_hotcpu_notifier(&via_cputemp_cpu_notifier);
 	return 0;
 
-exit_devices_unreg:
-	mutex_lock(&pdev_list_mutex);
-	list_for_each_entry_safe(p, n, &pdev_list, list) {
-		platform_device_unregister(p->pdev);
-		list_del(&p->list);
-		kfree(p);
-	}
-	mutex_unlock(&pdev_list_mutex);
+#ifndef CONFIG_HOTPLUG_CPU
 exit_driver_unreg:
 	platform_driver_unregister(&via_cputemp_driver);
+#endif
 exit:
 	return err;
 }

drivers/hwmon/via686a.c

@@ -30,6 +30,8 @@
     Warning - only supports a single device.
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/pci.h>
@@ -791,21 +793,19 @@ static int __devinit via686a_device_add(unsigned short address)
 	pdev = platform_device_alloc("via686a", address);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR "via686a: Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
 	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR "via686a: Device resource addition failed "
-		       "(%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR "via686a: Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 

drivers/hwmon/vt1211.c

@@ -21,6 +21,8 @@
  * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -1254,8 +1256,7 @@ static int __init vt1211_device_add(unsigned short address)
 	pdev = platform_device_alloc(DRVNAME, address);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Device allocation failed (%d)\n",
-		       err);
+		pr_err("Device allocation failed (%d)\n", err);
 		goto EXIT;
 	}
 
@@ -1266,15 +1267,13 @@ static int __init vt1211_device_add(unsigned short address)
 
 	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device resource addition failed "
-		       "(%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto EXIT_DEV_PUT;
 	}
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto EXIT_DEV_PUT;
 	}
 
@@ -1301,23 +1300,20 @@ static int __init vt1211_find(int sio_cip, unsigned short *address)
 	superio_select(sio_cip, SIO_VT1211_LDN_HWMON);
 
 	if ((superio_inb(sio_cip, SIO_VT1211_ACTIVE) & 1) == 0) {
-		printk(KERN_WARNING DRVNAME ": HW monitor is disabled, "
-		       "skipping\n");
+		pr_warn("HW monitor is disabled, skipping\n");
 		goto EXIT;
 	}
 
 	*address = ((superio_inb(sio_cip, SIO_VT1211_BADDR) << 8) |
 		    (superio_inb(sio_cip, SIO_VT1211_BADDR + 1))) & 0xff00;
 	if (*address == 0) {
-		printk(KERN_WARNING DRVNAME ": Base address is not set, "
-		       "skipping\n");
+		pr_warn("Base address is not set, skipping\n");
 		goto EXIT;
 	}
 
 	err = 0;
-	printk(KERN_INFO DRVNAME ": Found VT1211 chip at 0x%04x, "
-	       "revision %u\n", *address,
-	       superio_inb(sio_cip, SIO_VT1211_DEVREV));
+	pr_info("Found VT1211 chip at 0x%04x, revision %u\n",
+		*address, superio_inb(sio_cip, SIO_VT1211_DEVREV));
 
 EXIT:
 	superio_exit(sio_cip);
@@ -1336,15 +1332,15 @@ static int __init vt1211_init(void)
 
 	if ((uch_config < -1) || (uch_config > 31)) {
 		err = -EINVAL;
-		printk(KERN_WARNING DRVNAME ": Invalid UCH configuration %d. "
-		       "Choose a value between 0 and 31.\n", uch_config);
+		pr_warn("Invalid UCH configuration %d. "
+			"Choose a value between 0 and 31.\n", uch_config);
 	  goto EXIT;
 	}
 
 	if ((int_mode < -1) || (int_mode > 0)) {
 		err = -EINVAL;
-		printk(KERN_WARNING DRVNAME ": Invalid interrupt mode %d. "
-		       "Only mode 0 is supported.\n", int_mode);
+		pr_warn("Invalid interrupt mode %d. "
+			"Only mode 0 is supported.\n", int_mode);
 	  goto EXIT;
 	}
 

drivers/hwmon/vt8231.c

@@ -24,6 +24,8 @@
 /* Supports VIA VT8231 South Bridge embedded sensors
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -902,21 +904,19 @@ static int __devinit vt8231_device_add(unsigned short address)
 	pdev = platform_device_alloc("vt8231", address);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR "vt8231: Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
 	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR "vt8231: Device resource addition failed "
-		       "(%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR "vt8231: Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 

drivers/hwmon/w83627ehf.c

@@ -42,6 +42,8 @@
     w83667hg-b   9      5       3       3      0xb350 0xc1    0x5ca3
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -1668,8 +1670,7 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
 		break;
 	default:
 		if (val != 0xffff)
-			pr_debug(DRVNAME ": unsupported chip ID: 0x%04x\n",
-				 val);
+			pr_debug("unsupported chip ID: 0x%04x\n", val);
 		superio_exit(sioaddr);
 		return -ENODEV;
 	}
@@ -1680,8 +1681,7 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
 	    | superio_inb(sioaddr, SIO_REG_ADDR + 1);
 	*addr = val & IOREGION_ALIGNMENT;
 	if (*addr == 0) {
-		printk(KERN_ERR DRVNAME ": Refusing to enable a Super-I/O "
-		       "device with a base I/O port 0.\n");
+		pr_err("Refusing to enable a Super-I/O device with a base I/O port 0\n");
 		superio_exit(sioaddr);
 		return -ENODEV;
 	}
@@ -1689,13 +1689,12 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
 	/* Activate logical device if needed */
 	val = superio_inb(sioaddr, SIO_REG_ENABLE);
 	if (!(val & 0x01)) {
-		printk(KERN_WARNING DRVNAME ": Forcibly enabling Super-I/O. "
-		       "Sensor is probably unusable.\n");
+		pr_warn("Forcibly enabling Super-I/O. Sensor is probably unusable.\n");
 		superio_outb(sioaddr, SIO_REG_ENABLE, val | 0x01);
 	}
 
 	superio_exit(sioaddr);
-	pr_info(DRVNAME ": Found %s chip at %#x\n", sio_name, *addr);
+	pr_info("Found %s chip at %#x\n", sio_name, *addr);
 	sio_data->sioreg = sioaddr;
 
 	return 0;
@@ -1729,14 +1728,14 @@ static int __init sensors_w83627ehf_init(void)
 
 	if (!(pdev = platform_device_alloc(DRVNAME, address))) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit_unregister;
 	}
 
 	err = platform_device_add_data(pdev, &sio_data,
 				       sizeof(struct w83627ehf_sio_data));
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
+		pr_err("Platform data allocation failed\n");
 		goto exit_device_put;
 	}
 
@@ -1752,16 +1751,14 @@ static int __init sensors_w83627ehf_init(void)
 
 	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device resource addition failed "
-		       "(%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	/* platform_device_add calls probe() */
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 

drivers/hwmon/w83627hf.c

@@ -39,6 +39,8 @@
     supported yet.
 */
 
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
@@ -1166,14 +1168,13 @@ static int __init w83627hf_find(int sioaddr, unsigned short *addr,
 	       superio_inb(sio_data, WINB_BASE_REG + 1);
 	*addr = val & WINB_ALIGNMENT;
 	if (*addr == 0) {
-		printk(KERN_WARNING DRVNAME ": Base address not set, "
-		       "skipping\n");
+		pr_warn("Base address not set, skipping\n");
 		goto exit;
 	}
 
 	val = superio_inb(sio_data, WINB_ACT_REG);
 	if (!(val & 0x01)) {
-		printk(KERN_WARNING DRVNAME ": Enabling HWM logical device\n");
+		pr_warn("Enabling HWM logical device\n");
 		superio_outb(sio_data, WINB_ACT_REG, val | 0x01);
 	}
 
@@ -1789,28 +1790,26 @@ static int __init w83627hf_device_add(unsigned short address,
 	pdev = platform_device_alloc(DRVNAME, address);
 	if (!pdev) {
 		err = -ENOMEM;
-		printk(KERN_ERR DRVNAME ": Device allocation failed\n");
+		pr_err("Device allocation failed\n");
 		goto exit;
 	}
 
 	err = platform_device_add_resources(pdev, &res, 1);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device resource addition failed "
-		       "(%d)\n", err);
+		pr_err("Device resource addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 
 	err = platform_device_add_data(pdev, sio_data,
 				       sizeof(struct w83627hf_sio_data));
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Platform data allocation failed\n");
+		pr_err("Platform data allocation failed\n");
 		goto exit_device_put;
 	}
 
 	err = platform_device_add(pdev);
 	if (err) {
-		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
-		       err);
+		pr_err("Device addition failed (%d)\n", err);
 		goto exit_device_put;
 	}
 

include/linux/i2c/ds620.h

+#ifndef _LINUX_DS620_H
+#define _LINUX_DS620_H
+
+#include <linux/types.h>
+#include <linux/i2c.h>
+
+/* platform data for the DS620 temperature sensor and thermostat */
+
+struct ds620_platform_data {
+	/*
+	 *  Thermostat output pin PO mode:
+	 *  0 = always low (default)
+	 *  1 = PO_LOW
+	 *  2 = PO_HIGH
+	 *
+	 * (see Documentation/hwmon/ds620)
+	 */
+	int pomode;
+};
+
+#endif /* _LINUX_DS620_H */