Commit a306a65f authored by Pavel Rojtberg's avatar Pavel Rojtberg Committed by Dmitry Torokhov

Input: xpad - remove needless bulk out URB used for LED setup

This code was probably wrong ever since and is redundant with
xpad_send_led_command. Both try to send a similar command to the xbox360
controller. However xpad_send_led_command correctly uses the pad_nr instead
of bInterfaceNumber to select the led and re-uses the irq_out URB instead
of creating a new one.

Note that this change only affects the two supported wireless controllers.
Tested using the xbox360 wireless controller (PC).
Signed-off-by: default avatarPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: default avatarDmitry Torokhov <dmitry.torokhov@gmail.com>
parent e3b65174
......@@ -328,9 +328,6 @@ struct usb_xpad {
unsigned char *idata; /* input data */
dma_addr_t idata_dma;
struct urb *bulk_out;
unsigned char *bdata;
struct urb *irq_out; /* urb for interrupt out report */
unsigned char *odata; /* output data */
dma_addr_t odata_dma;
......@@ -510,7 +507,6 @@ static void xpad360w_process_packet(struct usb_xpad *xpad, u16 cmd, unsigned cha
if (data[0] & 0x08) {
if (data[1] & 0x80) {
xpad->pad_present = 1;
usb_submit_urb(xpad->bulk_out, GFP_ATOMIC);
/*
* Light up the segment corresponding to
* controller number.
......@@ -672,28 +668,6 @@ static void xpad_irq_in(struct urb *urb)
__func__, retval);
}
static void xpad_bulk_out(struct urb *urb)
{
struct usb_xpad *xpad = urb->context;
struct device *dev = &xpad->intf->dev;
switch (urb->status) {
case 0:
/* success */
break;
case -ECONNRESET:
case -ENOENT:
case -ESHUTDOWN:
/* this urb is terminated, clean up */
dev_dbg(dev, "%s - urb shutting down with status: %d\n",
__func__, urb->status);
break;
default:
dev_dbg(dev, "%s - nonzero urb status received: %d\n",
__func__, urb->status);
}
}
static void xpad_irq_out(struct urb *urb)
{
struct usb_xpad *xpad = urb->context;
......@@ -1229,52 +1203,6 @@ static int xpad_probe(struct usb_interface *intf, const struct usb_device_id *id
usb_set_intfdata(intf, xpad);
if (xpad->xtype == XTYPE_XBOX360W) {
/*
* Setup the message to set the LEDs on the
* controller when it shows up
*/
xpad->bulk_out = usb_alloc_urb(0, GFP_KERNEL);
if (!xpad->bulk_out) {
error = -ENOMEM;
goto fail7;
}
xpad->bdata = kzalloc(XPAD_PKT_LEN, GFP_KERNEL);
if (!xpad->bdata) {
error = -ENOMEM;
goto fail8;
}
xpad->bdata[2] = 0x08;
switch (intf->cur_altsetting->desc.bInterfaceNumber) {
case 0:
xpad->bdata[3] = 0x42;
break;
case 2:
xpad->bdata[3] = 0x43;
break;
case 4:
xpad->bdata[3] = 0x44;
break;
case 6:
xpad->bdata[3] = 0x45;
}
ep_irq_in = &intf->cur_altsetting->endpoint[1].desc;
if (usb_endpoint_is_bulk_out(ep_irq_in)) {
usb_fill_bulk_urb(xpad->bulk_out, udev,
usb_sndbulkpipe(udev,
ep_irq_in->bEndpointAddress),
xpad->bdata, XPAD_PKT_LEN,
xpad_bulk_out, xpad);
} else {
usb_fill_int_urb(xpad->bulk_out, udev,
usb_sndintpipe(udev,
ep_irq_in->bEndpointAddress),
xpad->bdata, XPAD_PKT_LEN,
xpad_bulk_out, xpad, 0);
}
/*
* Submit the int URB immediately rather than waiting for open
* because we get status messages from the device whether
......@@ -1285,13 +1213,11 @@ static int xpad_probe(struct usb_interface *intf, const struct usb_device_id *id
xpad->irq_in->dev = xpad->udev;
error = usb_submit_urb(xpad->irq_in, GFP_KERNEL);
if (error)
goto fail9;
goto fail7;
}
return 0;
fail9: kfree(xpad->bdata);
fail8: usb_free_urb(xpad->bulk_out);
fail7: input_unregister_device(input_dev);
input_dev = NULL;
fail6: xpad_led_disconnect(xpad);
......@@ -1315,8 +1241,6 @@ static void xpad_disconnect(struct usb_interface *intf)
xpad_deinit_output(xpad);
if (xpad->xtype == XTYPE_XBOX360W) {
usb_kill_urb(xpad->bulk_out);
usb_free_urb(xpad->bulk_out);
usb_kill_urb(xpad->irq_in);
}
......@@ -1324,7 +1248,6 @@ static void xpad_disconnect(struct usb_interface *intf)
usb_free_coherent(xpad->udev, XPAD_PKT_LEN,
xpad->idata, xpad->idata_dma);
kfree(xpad->bdata);
kfree(xpad);
usb_set_intfdata(intf, NULL);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment