Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull more i2c updates from Wolfram Sang:
 "Included are two bugfixes needing some bigger refactoring (sh_mobile:
  deferred probe with DMA, mv64xxx: fix offload support) and one
  deprecated driver removal I thought would go in via ppc but I
  misunderstood.  It has a proper ack from BenH"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: sh_mobile: fix uninitialized var when debug is enabled
  macintosh: therm_pm72: delete deprecated driver
  i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
  i2c: sh_mobile: rework deferred probing
  i2c: sh_mobile: refactor DMA setup
  i2c: mv64xxx: rework offload support to fix several problems
  i2c: mv64xxx: use BIT() macro for register value definitions

drivers/i2c/busses/Kconfig

@@ -753,6 +753,7 @@ config I2C_SH7760
 
 config I2C_SH_MOBILE
 	tristate "SuperH Mobile I2C Controller"
+	depends on HAS_DMA
 	depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST
 	help
 	  If you say yes to this option, support will be included for the

drivers/i2c/busses/i2c-sh_mobile.c

@@ -140,6 +140,7 @@ struct sh_mobile_i2c_data {
 	int sr;
 	bool send_stop;
 
+	struct resource *res;
 	struct dma_chan *dma_tx;
 	struct dma_chan *dma_rx;
 	struct scatterlist sg;
@@ -539,6 +540,42 @@ static void sh_mobile_i2c_dma_callback(void *data)
 	iic_set_clr(pd, ICIC, 0, ICIC_TDMAE | ICIC_RDMAE);
 }
 
+static struct dma_chan *sh_mobile_i2c_request_dma_chan(struct device *dev,
+				enum dma_transfer_direction dir, dma_addr_t port_addr)
+{
+	struct dma_chan *chan;
+	struct dma_slave_config cfg;
+	char *chan_name = dir == DMA_MEM_TO_DEV ? "tx" : "rx";
+	int ret;
+
+	chan = dma_request_slave_channel_reason(dev, chan_name);
+	if (IS_ERR(chan)) {
+		ret = PTR_ERR(chan);
+		dev_dbg(dev, "request_channel failed for %s (%d)\n", chan_name, ret);
+		return chan;
+	}
+
+	memset(&cfg, 0, sizeof(cfg));
+	cfg.direction = dir;
+	if (dir == DMA_MEM_TO_DEV) {
+		cfg.dst_addr = port_addr;
+		cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	} else {
+		cfg.src_addr = port_addr;
+		cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	}
+
+	ret = dmaengine_slave_config(chan, &cfg);
+	if (ret) {
+		dev_dbg(dev, "slave_config failed for %s (%d)\n", chan_name, ret);
+		dma_release_channel(chan);
+		return ERR_PTR(ret);
+	}
+
+	dev_dbg(dev, "got DMA channel for %s\n", chan_name);
+	return chan;
+}
+
 static void sh_mobile_i2c_xfer_dma(struct sh_mobile_i2c_data *pd)
 {
 	bool read = pd->msg->flags & I2C_M_RD;
@@ -548,7 +585,16 @@ static void sh_mobile_i2c_xfer_dma(struct sh_mobile_i2c_data *pd)
 	dma_addr_t dma_addr;
 	dma_cookie_t cookie;
 
-	if (!chan)
+	if (PTR_ERR(chan) == -EPROBE_DEFER) {
+		if (read)
+			chan = pd->dma_rx = sh_mobile_i2c_request_dma_chan(pd->dev, DMA_DEV_TO_MEM,
+									   pd->res->start + ICDR);
+		else
+			chan = pd->dma_tx = sh_mobile_i2c_request_dma_chan(pd->dev, DMA_MEM_TO_DEV,
+									   pd->res->start + ICDR);
+	}
+
+	if (IS_ERR(chan))
 		return;
 
 	dma_addr = dma_map_single(chan->device->dev, pd->msg->buf, pd->msg->len, dir);
@@ -747,56 +793,16 @@ static const struct of_device_id sh_mobile_i2c_dt_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, sh_mobile_i2c_dt_ids);
 
-static int sh_mobile_i2c_request_dma_chan(struct device *dev, enum dma_transfer_direction dir,
-					  dma_addr_t port_addr, struct dma_chan **chan_ptr)
-{
-	struct dma_chan *chan;
-	struct dma_slave_config cfg;
-	char *chan_name = dir == DMA_MEM_TO_DEV ? "tx" : "rx";
-	int ret;
-
-	*chan_ptr = NULL;
-
-	chan = dma_request_slave_channel_reason(dev, chan_name);
-	if (IS_ERR(chan)) {
-		ret = PTR_ERR(chan);
-		dev_dbg(dev, "request_channel failed for %s (%d)\n", chan_name, ret);
-		return ret;
-	}
-
-	memset(&cfg, 0, sizeof(cfg));
-	cfg.direction = dir;
-	if (dir == DMA_MEM_TO_DEV) {
-		cfg.dst_addr = port_addr;
-		cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	} else {
-		cfg.src_addr = port_addr;
-		cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
-	}
-
-	ret = dmaengine_slave_config(chan, &cfg);
-	if (ret) {
-		dev_dbg(dev, "slave_config failed for %s (%d)\n", chan_name, ret);
-		dma_release_channel(chan);
-		return ret;
-	}
-
-	*chan_ptr = chan;
-
-	dev_dbg(dev, "got DMA channel for %s\n", chan_name);
-	return 0;
-}
-
 static void sh_mobile_i2c_release_dma(struct sh_mobile_i2c_data *pd)
 {
-	if (pd->dma_tx) {
+	if (!IS_ERR(pd->dma_tx)) {
 		dma_release_channel(pd->dma_tx);
-		pd->dma_tx = NULL;
+		pd->dma_tx = ERR_PTR(-EPROBE_DEFER);
 	}
 
-	if (pd->dma_rx) {
+	if (!IS_ERR(pd->dma_rx)) {
 		dma_release_channel(pd->dma_rx);
-		pd->dma_rx = NULL;
+		pd->dma_rx = ERR_PTR(-EPROBE_DEFER);
 	}
 }
 
@@ -849,6 +855,7 @@ static int sh_mobile_i2c_probe(struct platform_device *dev)
 
 	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
 
+	pd->res = res;
 	pd->reg = devm_ioremap_resource(&dev->dev, res);
 	if (IS_ERR(pd->reg))
 		return PTR_ERR(pd->reg);
@@ -889,17 +896,7 @@ static int sh_mobile_i2c_probe(struct platform_device *dev)
 	/* Init DMA */
 	sg_init_table(&pd->sg, 1);
 	pd->dma_direction = DMA_NONE;
-	ret = sh_mobile_i2c_request_dma_chan(pd->dev, DMA_DEV_TO_MEM,
-					     res->start + ICDR, &pd->dma_rx);
-	if (ret == -EPROBE_DEFER)
-		return ret;
-
-	ret = sh_mobile_i2c_request_dma_chan(pd->dev, DMA_MEM_TO_DEV,
-					     res->start + ICDR, &pd->dma_tx);
-	if (ret == -EPROBE_DEFER) {
-		sh_mobile_i2c_release_dma(pd);
-		return ret;
-	}
+	pd->dma_rx = pd->dma_tx = ERR_PTR(-EPROBE_DEFER);
 
 	/* Enable Runtime PM for this device.
 	 *
@@ -937,8 +934,7 @@ static int sh_mobile_i2c_probe(struct platform_device *dev)
 		return ret;
 	}
 
-	dev_info(&dev->dev, "I2C adapter %d, bus speed %lu Hz, DMA=%c\n",
-		 adap->nr, pd->bus_speed, (pd->dma_rx || pd->dma_tx) ? 'y' : 'n');
+	dev_info(&dev->dev, "I2C adapter %d, bus speed %lu Hz\n", adap->nr, pd->bus_speed);
 
 	return 0;
 }

drivers/macintosh/Kconfig

@@ -204,16 +204,6 @@ config THERM_ADT746X
           iBook G4, and the ATI based aluminium PowerBooks, allowing slightly
 	  better fan behaviour by default, and some manual control.
 
-config THERM_PM72
-	tristate "Support for thermal management on PowerMac G5 (AGP)"
-	depends on I2C && I2C_POWERMAC && PPC_PMAC64
-	default n
-	help
-	  This driver provides thermostat and fan control for the desktop
-	  G5 machines.
-
-	  This is deprecated, use windfarm instead.
-
 config WINDFARM
 	tristate "New PowerMac thermal control infrastructure"
 	depends on PPC

drivers/macintosh/Makefile

@@ -25,7 +25,6 @@ obj-$(CONFIG_ADB_IOP)		+= adb-iop.o
 obj-$(CONFIG_ADB_PMU68K)	+= via-pmu68k.o
 obj-$(CONFIG_ADB_MACIO)		+= macio-adb.o
 
-obj-$(CONFIG_THERM_PM72)	+= therm_pm72.o
 obj-$(CONFIG_THERM_WINDTUNNEL)	+= therm_windtunnel.o
 obj-$(CONFIG_THERM_ADT746X)	+= therm_adt746x.o
 obj-$(CONFIG_WINDFARM)	        += windfarm_core.o

drivers/macintosh/therm_pm72.h

-#ifndef __THERM_PMAC_7_2_H__
-#define __THERM_PMAC_7_2_H__
-
-typedef unsigned short fu16;
-typedef int fs32;
-typedef short fs16;
-
-struct mpu_data
-{
-	u8	signature;		/* 0x00 - EEPROM sig. */
-	u8	bytes_used;		/* 0x01 - Bytes used in eeprom (160 ?) */
-	u8	size;			/* 0x02 - EEPROM size (256 ?) */
-	u8	version;		/* 0x03 - EEPROM version */
-	u32	data_revision;		/* 0x04 - Dataset revision */
-	u8	processor_bin_code[3];	/* 0x08 - Processor BIN code */
-	u8	bin_code_expansion;	/* 0x0b - ??? (padding ?) */
-	u8	processor_num;		/* 0x0c - Number of CPUs on this MPU */
-	u8	input_mul_bus_div;	/* 0x0d - Clock input multiplier/bus divider */
-	u8	reserved1[2];		/* 0x0e - */
-	u32	input_clk_freq_high;	/* 0x10 - Input clock frequency high */
-	u8	cpu_nb_target_cycles;	/* 0x14 - ??? */
-	u8	cpu_statlat;		/* 0x15 - ??? */
-	u8	cpu_snooplat;		/* 0x16 - ??? */
-	u8	cpu_snoopacc;		/* 0x17 - ??? */
-	u8	nb_paamwin;		/* 0x18 - ??? */
-	u8	nb_statlat;		/* 0x19 - ??? */
-	u8	nb_snooplat;		/* 0x1a - ??? */
-	u8	nb_snoopwin;		/* 0x1b - ??? */
-	u8	api_bus_mode;		/* 0x1c - ??? */
-	u8	reserved2[3];		/* 0x1d - */
-	u32	input_clk_freq_low;	/* 0x20 - Input clock frequency low */
-	u8	processor_card_slot;	/* 0x24 - Processor card slot number */
-	u8	reserved3[2];		/* 0x25 - */
-	u8	padjmax;       		/* 0x27 - Max power adjustment (Not in OF!) */
-	u8	ttarget;		/* 0x28 - Target temperature */
-	u8	tmax;			/* 0x29 - Max temperature */
-	u8	pmaxh;			/* 0x2a - Max power */
-	u8	tguardband;		/* 0x2b - Guardband temp ??? Hist. len in OSX */
-	fs32	pid_gp;			/* 0x2c - PID proportional gain */
-	fs32	pid_gr;			/* 0x30 - PID reset gain */
-	fs32	pid_gd;			/* 0x34 - PID derivative gain */
-	fu16	voph;			/* 0x38 - Vop High */
-	fu16	vopl;			/* 0x3a - Vop Low */
-	fs16	nactual_die;		/* 0x3c - nActual Die */
-	fs16	nactual_heatsink;	/* 0x3e - nActual Heatsink */
-	fs16	nactual_system;		/* 0x40 - nActual System */
-	u16	calibration_flags;	/* 0x42 - Calibration flags */
-	fu16	mdiode;			/* 0x44 - Diode M value (scaling factor) */
-	fs16	bdiode;			/* 0x46 - Diode B value (offset) */
-	fs32	theta_heat_sink;	/* 0x48 - Theta heat sink */
-	u16	rminn_intake_fan;	/* 0x4c - Intake fan min RPM */
-	u16	rmaxn_intake_fan;	/* 0x4e - Intake fan max RPM */
-	u16	rminn_exhaust_fan;	/* 0x50 - Exhaust fan min RPM */
-	u16	rmaxn_exhaust_fan;	/* 0x52 - Exhaust fan max RPM */
-	u8	processor_part_num[8];	/* 0x54 - Processor part number XX pumps min/max */
-	u32	processor_lot_num;	/* 0x5c - Processor lot number */
-	u8	orig_card_sernum[0x10];	/* 0x60 - Card original serial number */
-	u8	curr_card_sernum[0x10];	/* 0x70 - Card current serial number */
-	u8	mlb_sernum[0x18];	/* 0x80 - MLB serial number */
-	u32	checksum1;		/* 0x98 - */
-	u32	checksum2;		/* 0x9c - */	
-}; /* Total size = 0xa0 */
-
-/* Display a 16.16 fixed point value */
-#define FIX32TOPRINT(f)	((f) >> 16),((((f) & 0xffff) * 1000) >> 16)
-
-/*
- * Maximum number of seconds to be in critical state (after a
- * normal shutdown attempt). If the machine isn't down after
- * this counter elapses, we force an immediate machine power
- * off.
- */
-#define MAX_CRITICAL_STATE			30
-static char * critical_overtemp_path = "/sbin/critical_overtemp";
-
-/*
- * This option is "weird" :) Basically, if you define this to 1
- * the control loop for the RPMs fans (not PWMs) will apply the
- * correction factor obtained from the PID to the _actual_ RPM
- * speed read from the FCU.
- * If you define the below constant to 0, then it will be
- * applied to the setpoint RPM speed, that is basically the
- * speed we proviously "asked" for.
- *
- * I'm not sure which of these Apple's algorithm is supposed
- * to use
- */
-#define RPM_PID_USE_ACTUAL_SPEED		0
-
-/*
- * i2c IDs. Currently, we hard code those and assume that
- * the FCU is on U3 bus 1 while all sensors are on U3 bus
- * 0. This appear to be safe enough for this first version
- * of the driver, though I would accept any clean patch
- * doing a better use of the device-tree without turning the
- * while i2c registration mechanism into a racy mess
- *
- * Note: Xserve changed this. We have some bits on the K2 bus,
- * which I arbitrarily set to 0x200. Ultimately, we really want
- * too lookup these in the device-tree though
- */
-#define FAN_CTRLER_ID		0x15e
-#define SUPPLY_MONITOR_ID      	0x58
-#define SUPPLY_MONITORB_ID     	0x5a
-#define DRIVES_DALLAS_ID	0x94
-#define BACKSIDE_MAX_ID		0x98
-#define XSERVE_DIMMS_LM87	0x25a
-#define XSERVE_SLOTS_LM75	0x290
-
-/*
- * Some MAX6690, DS1775, LM87 register definitions
- */
-#define MAX6690_INT_TEMP	0
-#define MAX6690_EXT_TEMP	1
-#define DS1775_TEMP		0
-#define LM87_INT_TEMP		0x27
-
-/*
- * Scaling factors for the AD7417 ADC converters (except
- * for the CPU diode which is obtained from the EEPROM).
- * Those values are obtained from the property list of
- * the darwin driver
- */
-#define ADC_12V_CURRENT_SCALE	0x0320	/* _AD2 */
-#define ADC_CPU_VOLTAGE_SCALE	0x00a0	/* _AD3 */
-#define ADC_CPU_CURRENT_SCALE	0x1f40	/* _AD4 */
-
-/*
- * PID factors for the U3/Backside fan control loop. We have 2 sets
- * of values here, one set for U3 and one set for U3H
- */
-#define BACKSIDE_FAN_PWM_DEFAULT_ID	1
-#define BACKSIDE_FAN_PWM_INDEX		0
-#define BACKSIDE_PID_U3_G_d		0x02800000
-#define BACKSIDE_PID_U3H_G_d		0x01400000
-#define BACKSIDE_PID_RACK_G_d		0x00500000
-#define BACKSIDE_PID_G_p		0x00500000
-#define BACKSIDE_PID_RACK_G_p		0x0004cccc
-#define BACKSIDE_PID_G_r		0x00000000
-#define BACKSIDE_PID_U3_INPUT_TARGET	0x00410000
-#define BACKSIDE_PID_U3H_INPUT_TARGET	0x004b0000
-#define BACKSIDE_PID_RACK_INPUT_TARGET	0x00460000
-#define BACKSIDE_PID_INTERVAL		5
-#define BACKSIDE_PID_RACK_INTERVAL	1
-#define BACKSIDE_PID_OUTPUT_MAX		100
-#define BACKSIDE_PID_U3_OUTPUT_MIN	20
-#define BACKSIDE_PID_U3H_OUTPUT_MIN	20
-#define BACKSIDE_PID_HISTORY_SIZE	2
-
-struct basckside_pid_params
-{
-	s32			G_d;
-	s32			G_p;
-	s32			G_r;
-	s32			input_target;
-	s32			output_min;
-	s32			output_max;
-	s32			interval;
-	int			additive;
-};
-
-struct backside_pid_state
-{
-	int			ticks;
-	struct i2c_client *	monitor;
-	s32		       	sample_history[BACKSIDE_PID_HISTORY_SIZE];
-	s32			error_history[BACKSIDE_PID_HISTORY_SIZE];
-	int			cur_sample;
-	s32			last_temp;
-	int			pwm;
-	int			first;
-};
-
-/*
- * PID factors for the Drive Bay fan control loop
- */
-#define DRIVES_FAN_RPM_DEFAULT_ID	2
-#define DRIVES_FAN_RPM_INDEX		1
-#define DRIVES_PID_G_d			0x01e00000
-#define DRIVES_PID_G_p			0x00500000
-#define DRIVES_PID_G_r			0x00000000
-#define DRIVES_PID_INPUT_TARGET		0x00280000
-#define DRIVES_PID_INTERVAL    		5
-#define DRIVES_PID_OUTPUT_MAX		4000
-#define DRIVES_PID_OUTPUT_MIN		300
-#define DRIVES_PID_HISTORY_SIZE		2
-
-struct drives_pid_state
-{
-	int			ticks;
-	struct i2c_client *	monitor;
-	s32	       		sample_history[BACKSIDE_PID_HISTORY_SIZE];
-	s32			error_history[BACKSIDE_PID_HISTORY_SIZE];
-	int			cur_sample;
-	s32			last_temp;
-	int			rpm;
-	int			first;
-};
-
-#define SLOTS_FAN_PWM_DEFAULT_ID	2
-#define SLOTS_FAN_PWM_INDEX		2
-#define	SLOTS_FAN_DEFAULT_PWM		40 /* Do better here ! */
-
-
-/*
- * PID factors for the Xserve DIMM control loop
- */
-#define DIMM_PID_G_d			0
-#define DIMM_PID_G_p			0
-#define DIMM_PID_G_r			0x06553600
-#define DIMM_PID_INPUT_TARGET		3276800
-#define DIMM_PID_INTERVAL    		1
-#define DIMM_PID_OUTPUT_MAX		14000
-#define DIMM_PID_OUTPUT_MIN		4000
-#define DIMM_PID_HISTORY_SIZE		20
-
-struct dimm_pid_state
-{
-	int			ticks;
-	struct i2c_client *	monitor;
-	s32	       		sample_history[DIMM_PID_HISTORY_SIZE];
-	s32			error_history[DIMM_PID_HISTORY_SIZE];
-	int			cur_sample;
-	s32			last_temp;
-	int			first;
-	int			output;
-};
-
-
-/*
- * PID factors for the Xserve Slots control loop
- */
-#define SLOTS_PID_G_d			0
-#define SLOTS_PID_G_p			0
-#define SLOTS_PID_G_r			0x00100000
-#define SLOTS_PID_INPUT_TARGET		3200000
-#define SLOTS_PID_INTERVAL    		1
-#define SLOTS_PID_OUTPUT_MAX		100
-#define SLOTS_PID_OUTPUT_MIN		20
-#define SLOTS_PID_HISTORY_SIZE		20
-
-struct slots_pid_state
-{
-	int			ticks;
-	struct i2c_client *	monitor;
-	s32	       		sample_history[SLOTS_PID_HISTORY_SIZE];
-	s32			error_history[SLOTS_PID_HISTORY_SIZE];
-	int			cur_sample;
-	s32			last_temp;
-	int			first;
-	int			pwm;
-};
-
-
-
-/* Desktops */
-
-#define CPUA_INTAKE_FAN_RPM_DEFAULT_ID	3
-#define CPUA_EXHAUST_FAN_RPM_DEFAULT_ID	4
-#define CPUB_INTAKE_FAN_RPM_DEFAULT_ID	5
-#define CPUB_EXHAUST_FAN_RPM_DEFAULT_ID	6
-
-#define CPUA_INTAKE_FAN_RPM_INDEX	3
-#define CPUA_EXHAUST_FAN_RPM_INDEX	4
-#define CPUB_INTAKE_FAN_RPM_INDEX	5
-#define CPUB_EXHAUST_FAN_RPM_INDEX	6
-
-#define CPU_INTAKE_SCALE		0x0000f852
-#define CPU_TEMP_HISTORY_SIZE		2
-#define CPU_POWER_HISTORY_SIZE		10
-#define CPU_PID_INTERVAL		1
-#define CPU_MAX_OVERTEMP		90
-
-#define CPUA_PUMP_RPM_INDEX		7
-#define CPUB_PUMP_RPM_INDEX		8
-#define CPU_PUMP_OUTPUT_MAX		3200
-#define CPU_PUMP_OUTPUT_MIN		1250
-
-/* Xserve */
-#define CPU_A1_FAN_RPM_INDEX		9
-#define CPU_A2_FAN_RPM_INDEX		10
-#define CPU_A3_FAN_RPM_INDEX		11
-#define CPU_B1_FAN_RPM_INDEX		12
-#define CPU_B2_FAN_RPM_INDEX		13
-#define CPU_B3_FAN_RPM_INDEX		14
-
-
-struct cpu_pid_state
-{
-	int			index;
-	struct i2c_client *	monitor;
-	struct mpu_data		mpu;
-	int			overtemp;
-	s32	       		temp_history[CPU_TEMP_HISTORY_SIZE];
-	int			cur_temp;
-	s32			power_history[CPU_POWER_HISTORY_SIZE];
-	s32			error_history[CPU_POWER_HISTORY_SIZE];
-	int			cur_power;
-	int			count_power;
-	int			rpm;
-	int			intake_rpm;
-	s32			voltage;
-	s32			current_a;
-	s32			last_temp;
-	s32			last_power;
-	int			first;
-	u8			adc_config;
-	s32			pump_min;
-	s32			pump_max;
-};
-
-/* Tickle FCU every 10 seconds */
-#define FCU_TICKLE_TICKS	10
-
-/*
- * Driver state
- */
-enum {
-	state_detached,
-	state_attaching,
-	state_attached,
-	state_detaching,
-};
-
-
-#endif /* __THERM_PMAC_7_2_H__ */