Merge branch 'amd-xgbe-next'

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver update 2014-08-01

The following series of patches includes minor fixes/updates to the
driver.

- Remove some uses of spinlock around ethtool/phylib areas
- Update Rx/Tx ready check logic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c

@@ -290,13 +290,9 @@ static int xgbe_get_settings(struct net_device *netdev,
 	if (!pdata->phydev)
 		return -ENODEV;
 
-	spin_lock_irq(&pdata->lock);
-
 	ret = phy_ethtool_gset(pdata->phydev, cmd);
 	cmd->transceiver = XCVR_EXTERNAL;
 
-	spin_unlock_irq(&pdata->lock);
-
 	DBGPR("<--xgbe_get_settings\n");
 
 	return ret;
@@ -315,17 +311,14 @@ static int xgbe_set_settings(struct net_device *netdev,
 	if (!pdata->phydev)
 		return -ENODEV;
 
-	spin_lock_irq(&pdata->lock);
-
 	speed = ethtool_cmd_speed(cmd);
 
-	ret = -EINVAL;
 	if (cmd->phy_address != phydev->addr)
-		goto unlock;
+		return -EINVAL;
 
 	if ((cmd->autoneg != AUTONEG_ENABLE) &&
 	    (cmd->autoneg != AUTONEG_DISABLE))
-		goto unlock;
+		return -EINVAL;
 
 	if (cmd->autoneg == AUTONEG_DISABLE) {
 		switch (speed) {
@@ -334,16 +327,16 @@ static int xgbe_set_settings(struct net_device *netdev,
 		case SPEED_1000:
 			break;
 		default:
-			goto unlock;
+			return -EINVAL;
 		}
 
 		if (cmd->duplex != DUPLEX_FULL)
-			goto unlock;
+			return -EINVAL;
 	}
 
 	cmd->advertising &= phydev->supported;
 	if ((cmd->autoneg == AUTONEG_ENABLE) && !cmd->advertising)
-		goto unlock;
+		return -EINVAL;
 
 	ret = 0;
 	phydev->autoneg = cmd->autoneg;
@@ -359,9 +352,6 @@ static int xgbe_set_settings(struct net_device *netdev,
 	if (netif_running(netdev))
 		ret = phy_start_aneg(phydev);
 
-unlock:
-	spin_unlock_irq(&pdata->lock);
-
 	DBGPR("<--xgbe_set_settings\n");
 
 	return ret;

drivers/net/ethernet/amd/xgbe/xgbe-mdio.c

@@ -163,7 +163,6 @@ static void xgbe_adjust_link(struct net_device *netdev)
 	struct xgbe_prv_data *pdata = netdev_priv(netdev);
 	struct xgbe_hw_if *hw_if = &pdata->hw_if;
 	struct phy_device *phydev = pdata->phydev;
-	unsigned long flags;
 	int new_state = 0;
 
 	if (phydev == NULL)
@@ -172,8 +171,6 @@ static void xgbe_adjust_link(struct net_device *netdev)
 	DBGPR_MDIO("-->xgbe_adjust_link: address=%d, newlink=%d, curlink=%d\n",
 		   phydev->addr, phydev->link, pdata->phy_link);
 
-	spin_lock_irqsave(&pdata->lock, flags);
-
 	if (phydev->link) {
 		/* Flow control support */
 		if (pdata->pause_autoneg) {
@@ -229,8 +226,6 @@ static void xgbe_adjust_link(struct net_device *netdev)
 	if (new_state)
 		phy_print_status(phydev);
 
-	spin_unlock_irqrestore(&pdata->lock, flags);
-
 	DBGPR_MDIO("<--xgbe_adjust_link\n");
 }
 

drivers/net/phy/amd-xgbe-phy.c

@@ -95,7 +95,7 @@ MODULE_DESCRIPTION("AMD 10GbE (amd-xgbe) PHY driver");
 #define XNP_MP_FORMATTED		(1 << 13)
 #define XNP_NP_EXCHANGE			(1 << 15)
 
-#define XGBE_PHY_RATECHANGE_COUNT	100
+#define XGBE_PHY_RATECHANGE_COUNT	500
 
 #ifndef MDIO_PMA_10GBR_PMD_CTRL
 #define MDIO_PMA_10GBR_PMD_CTRL		0x0096
@@ -411,7 +411,7 @@ static void amd_xgbe_phy_serdes_complete_ratechange(struct phy_device *phydev)
 	/* Wait for Rx and Tx ready */
 	wait = XGBE_PHY_RATECHANGE_COUNT;
 	while (wait--) {
-		usleep_range(10, 20);
+		usleep_range(50, 75);
 
 		status = XSIR0_IOREAD(priv, SIR0_STATUS);
 		if (XSIR_GET_BITS(status, SIR0_STATUS, RX_READY) &&
@@ -419,7 +419,7 @@ static void amd_xgbe_phy_serdes_complete_ratechange(struct phy_device *phydev)
 			return;
 	}
 
-	netdev_err(phydev->attached_dev, "SerDes rx/tx not ready (%#hx)\n",
+	netdev_dbg(phydev->attached_dev, "SerDes rx/tx not ready (%#hx)\n",
 		   status);
 }