Merge tag 'iio-fixes-5.14a' of...

Merge tag 'iio-fixes-5.14a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First set of fixes for IIO in the 5.14 cycle

adi,adis:
 - Ensure GPIO pin direction set explicitly in driver.
fxls8952af:
 - Fix use of ret when not initialized.
 - Fix issue with use of module symbol from built in.
hdc100x:
 - Add a margin to conversion time as some parts run to slowly.
palmas-adc:
 - Fix a wrong exit condition that leads to adc period always being set
   to maximum value.
st,sensors:
 - Drop a wrong restriction on number of interrupts in dt binding.
ti-ads7950:
 - Ensure CS deasserted after channel read.

* tag 'iio-fixes-5.14a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
  iio: adc: Fix incorrect exit of for-loop
  iio: humidity: hdc100x: Add margin to the conversion time
  dt-bindings: iio: st: Remove wrong items length check
  iio: accel: fxls8962af: fix i2c dependency
  iio: adis: set GPIO reset pin direction
  iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels
  iio: accel: fxls8962af: fix potential use of uninitialized symbol

Documentation/devicetree/bindings/iio/st,st-sensors.yaml

@@ -152,47 +152,6 @@ allOf:
           maxItems: 1
         st,drdy-int-pin: false
 
-  - if:
-      properties:
-        compatible:
-          enum:
-            # Two intertial interrupts i.e. accelerometer/gyro interrupts
-            - st,h3lis331dl-accel
-            - st,l3g4200d-gyro
-            - st,l3g4is-gyro
-            - st,l3gd20-gyro
-            - st,l3gd20h-gyro
-            - st,lis2de12
-            - st,lis2dw12
-            - st,lis2hh12
-            - st,lis2dh12-accel
-            - st,lis331dl-accel
-            - st,lis331dlh-accel
-            - st,lis3de
-            - st,lis3dh-accel
-            - st,lis3dhh
-            - st,lis3mdl-magn
-            - st,lng2dm-accel
-            - st,lps331ap-press
-            - st,lsm303agr-accel
-            - st,lsm303dlh-accel
-            - st,lsm303dlhc-accel
-            - st,lsm303dlm-accel
-            - st,lsm330-accel
-            - st,lsm330-gyro
-            - st,lsm330d-accel
-            - st,lsm330d-gyro
-            - st,lsm330dl-accel
-            - st,lsm330dl-gyro
-            - st,lsm330dlc-accel
-            - st,lsm330dlc-gyro
-            - st,lsm9ds0-gyro
-            - st,lsm9ds1-magn
-    then:
-      properties:
-        interrupts:
-          maxItems: 2
-
 required:
   - compatible
   - reg

drivers/iio/accel/Kconfig

@@ -231,6 +231,7 @@ config DMARD10
 
 config FXLS8962AF
 	tristate
+	depends on I2C || !I2C # cannot be built-in for modular I2C
 
 config FXLS8962AF_I2C
 	tristate "NXP FXLS8962AF/FXLS8964AF Accelerometer I2C Driver"
@@ -247,6 +248,7 @@ config FXLS8962AF_I2C
 config FXLS8962AF_SPI
 	tristate "NXP FXLS8962AF/FXLS8964AF Accelerometer SPI Driver"
 	depends on SPI
+	depends on I2C || !I2C
 	select FXLS8962AF
 	select REGMAP_SPI
 	help

drivers/iio/accel/fxls8962af-core.c

@@ -637,7 +637,7 @@ static int fxls8962af_i2c_raw_read_errata3(struct fxls8962af_data *data,
 			return ret;
 	}
 
-	return ret;
+	return 0;
 }
 
 static int fxls8962af_fifo_transfer(struct fxls8962af_data *data,

drivers/iio/adc/palmas_gpadc.c

@@ -664,8 +664,8 @@ static int palmas_adc_wakeup_configure(struct palmas_gpadc *adc)
 
 	adc_period = adc->auto_conversion_period;
 	for (i = 0; i < 16; ++i) {
-		if (((1000 * (1 << i)) / 32) < adc_period)
-			continue;
+		if (((1000 * (1 << i)) / 32) >= adc_period)
+			break;
 	}
 	if (i > 0)
 		i--;

drivers/iio/adc/ti-ads7950.c

@@ -568,7 +568,6 @@ static int ti_ads7950_probe(struct spi_device *spi)
 	st->ring_xfer.tx_buf = &st->tx_buf[0];
 	st->ring_xfer.rx_buf = &st->rx_buf[0];
 	/* len will be set later */
-	st->ring_xfer.cs_change = true;
 
 	spi_message_add_tail(&st->ring_xfer, &st->ring_msg);
 

drivers/iio/humidity/hdc100x.c

@@ -25,6 +25,8 @@
 #include <linux/iio/trigger_consumer.h>
 #include <linux/iio/triggered_buffer.h>
 
+#include <linux/time.h>
+
 #define HDC100X_REG_TEMP			0x00
 #define HDC100X_REG_HUMIDITY			0x01
 
@@ -166,7 +168,7 @@ static int hdc100x_get_measurement(struct hdc100x_data *data,
 				   struct iio_chan_spec const *chan)
 {
 	struct i2c_client *client = data->client;
-	int delay = data->adc_int_us[chan->address];
+	int delay = data->adc_int_us[chan->address] + 1*USEC_PER_MSEC;
 	int ret;
 	__be16 val;
 
@@ -316,7 +318,7 @@ static irqreturn_t hdc100x_trigger_handler(int irq, void *p)
 	struct iio_dev *indio_dev = pf->indio_dev;
 	struct hdc100x_data *data = iio_priv(indio_dev);
 	struct i2c_client *client = data->client;
-	int delay = data->adc_int_us[0] + data->adc_int_us[1];
+	int delay = data->adc_int_us[0] + data->adc_int_us[1] + 2*USEC_PER_MSEC;
 	int ret;
 
 	/* dual read starts at temp register */

drivers/iio/imu/adis.c

@@ -411,12 +411,11 @@ int __adis_initial_startup(struct adis *adis)
 	int ret;
 
 	/* check if the device has rst pin low */
-	gpio = devm_gpiod_get_optional(&adis->spi->dev, "reset", GPIOD_ASIS);
+	gpio = devm_gpiod_get_optional(&adis->spi->dev, "reset", GPIOD_OUT_HIGH);
 	if (IS_ERR(gpio))
 		return PTR_ERR(gpio);
 
 	if (gpio) {
-		gpiod_set_value_cansleep(gpio, 1);
 		msleep(10);
 		/* bring device out of reset */
 		gpiod_set_value_cansleep(gpio, 0);