Commit a6044e23 authored by Jesse Barnes's avatar Jesse Barnes Committed by Chris Wilson

drm/i915: support overclocking on Sandy Bridge

In some configuration, the PCU may allow us to overclock the GPU.
Check for this case and adjust the max frequency as appropriate.  Also
initialize the min/max frequencies to default values as indicated by
hardware.
Signed-off-by: default avatarJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: default avatarChris Wilson <chris@chris-wilson.co.uk>
parent bee17e5a
...@@ -3240,6 +3240,7 @@ ...@@ -3240,6 +3240,7 @@
#define GEN6_PCODE_MAILBOX 0x138124 #define GEN6_PCODE_MAILBOX 0x138124
#define GEN6_PCODE_READY (1<<31) #define GEN6_PCODE_READY (1<<31)
#define GEN6_READ_OC_PARAMS 0xc
#define GEN6_PCODE_WRITE_MIN_FREQ_TABLE 0x9 #define GEN6_PCODE_WRITE_MIN_FREQ_TABLE 0x9
#define GEN6_PCODE_DATA 0x138128 #define GEN6_PCODE_DATA 0x138128
......
...@@ -6147,6 +6147,10 @@ void intel_init_emon(struct drm_device *dev) ...@@ -6147,6 +6147,10 @@ void intel_init_emon(struct drm_device *dev)
void gen6_enable_rps(struct drm_i915_private *dev_priv) void gen6_enable_rps(struct drm_i915_private *dev_priv)
{ {
u32 rp_state_cap = I915_READ(GEN6_RP_STATE_CAP);
u32 gt_perf_status = I915_READ(GEN6_GT_PERF_STATUS);
u32 pcu_mbox;
int cur_freq, min_freq, max_freq;
int i; int i;
/* Here begins a magic sequence of register writes to enable /* Here begins a magic sequence of register writes to enable
...@@ -6218,6 +6222,29 @@ void gen6_enable_rps(struct drm_i915_private *dev_priv) ...@@ -6218,6 +6222,29 @@ void gen6_enable_rps(struct drm_i915_private *dev_priv)
500)) 500))
DRM_ERROR("timeout waiting for pcode mailbox to finish\n"); DRM_ERROR("timeout waiting for pcode mailbox to finish\n");
min_freq = (rp_state_cap & 0xff0000) >> 16;
max_freq = rp_state_cap & 0xff;
cur_freq = (gt_perf_status & 0xff00) >> 8;
/* Check for overclock support */
if (wait_for((I915_READ(GEN6_PCODE_MAILBOX) & GEN6_PCODE_READY) == 0,
500))
DRM_ERROR("timeout waiting for pcode mailbox to become idle\n");
I915_WRITE(GEN6_PCODE_MAILBOX, GEN6_READ_OC_PARAMS);
pcu_mbox = I915_READ(GEN6_PCODE_DATA);
if (wait_for((I915_READ(GEN6_PCODE_MAILBOX) & GEN6_PCODE_READY) == 0,
500))
DRM_ERROR("timeout waiting for pcode mailbox to finish\n");
if (pcu_mbox & (1<<31)) { /* OC supported */
max_freq = pcu_mbox & 0xff;
DRM_DEBUG_DRIVER("overclocking supported, adjusting frequency max to %dMHz\n", pcu_mbox * 100);
}
/* In units of 100MHz */
dev_priv->max_delay = max_freq;
dev_priv->min_delay = min_freq;
dev_priv->cur_delay = cur_freq;
/* requires MSI enabled */ /* requires MSI enabled */
I915_WRITE(GEN6_PMIER, I915_WRITE(GEN6_PMIER,
GEN6_PM_MBOX_EVENT | GEN6_PM_MBOX_EVENT |
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment