Merge remote-tracking branches 'asoc/topic/fsl', 'asoc/topic/fsl-card',...

Merge remote-tracking branches 'asoc/topic/fsl', 'asoc/topic/fsl-card', 'asoc/topic/fsl-dt' and 'asoc/topic/fsl-ssi' into asoc-next

Documentation/devicetree/bindings/sound/eukrea-tlv320.txt

 Audio complex for Eukrea boards with tlv320aic23 codec.
 
 Required properties:
-- compatible : "eukrea,asoc-tlv320"
-- eukrea,model : The user-visible name of this sound complex.
-- ssi-controller : The phandle of the SSI controller.
-- fsl,mux-int-port : The internal port of the i.MX audio muxer (AUDMUX).
-- fsl,mux-ext-port : The external port of the i.MX audio muxer.
+
+  - compatible		: "eukrea,asoc-tlv320"
+
+  - eukrea,model	: The user-visible name of this sound complex.
+
+  - ssi-controller	: The phandle of the SSI controller.
+
+  - fsl,mux-int-port	: The internal port of the i.MX audio muxer (AUDMUX).
+
+  - fsl,mux-ext-port	: The external port of the i.MX audio muxer.
 
 Note: The AUDMUX port numbering should start at 1, which is consistent with
 hardware manual.

Documentation/devicetree/bindings/sound/fsl,esai.txt

@@ -7,37 +7,39 @@ other DSPs. It has up to six transmitters and four receivers.
 
 Required properties:
 
-  - compatible : Compatible list, must contain "fsl,imx35-esai" or
-		 "fsl,vf610-esai"
+  - compatible		: Compatible list, must contain "fsl,imx35-esai" or
+			  "fsl,vf610-esai"
 
-  - reg : Offset and length of the register set for the device.
+  - reg			: Offset and length of the register set for the device.
 
-  - interrupts : Contains the spdif interrupt.
+  - interrupts		: Contains the spdif interrupt.
 
-  - dmas : Generic dma devicetree binding as described in
-  Documentation/devicetree/bindings/dma/dma.txt.
+  - dmas		: Generic dma devicetree binding as described in
+			  Documentation/devicetree/bindings/dma/dma.txt.
 
-  - dma-names : Two dmas have to be defined, "tx" and "rx".
+  - dma-names		: Two dmas have to be defined, "tx" and "rx".
 
-  - clocks: Contains an entry for each entry in clock-names.
+  - clocks		: Contains an entry for each entry in clock-names.
 
-  - clock-names : Includes the following entries:
-	"core"		The core clock used to access registers
-	"extal"		The esai baud clock for esai controller used to derive
-			HCK, SCK and FS.
-	"fsys"		The system clock derived from ahb clock used to derive
-			HCK, SCK and FS.
+  - clock-names		: Includes the following entries:
+	"core"		  The core clock used to access registers
+	"extal"		  The esai baud clock for esai controller used to
+			  derive HCK, SCK and FS.
+	"fsys"		  The system clock derived from ahb clock used to
+			  derive HCK, SCK and FS.
 
-  - fsl,fifo-depth: The number of elements in the transmit and receive FIFOs.
-    This number is the maximum allowed value for TFCR[TFWM] or RFCR[RFWM].
+  - fsl,fifo-depth	: The number of elements in the transmit and receive
+			  FIFOs. This number is the maximum allowed value for
+			  TFCR[TFWM] or RFCR[RFWM].
 
   - fsl,esai-synchronous: This is a boolean property. If present, indicating
-    that ESAI would work in the synchronous mode, which means all the settings
-    for Receiving would be duplicated from Transmition related registers.
+			  that ESAI would work in the synchronous mode, which
+			  means all the settings for Receiving would be
+			  duplicated from Transmition related registers.
 
-  - big-endian : If this property is absent, the native endian mode will
-    be in use as default, or the big endian mode will be in use for all the
-    device registers.
+  - big-endian		: If this property is absent, the native endian mode
+			  will be in use as default, or the big endian mode
+			  will be in use for all the device registers.
 
 Example:
 

Documentation/devicetree/bindings/sound/fsl,spdif.txt

@@ -6,32 +6,31 @@ a fibre cable.
 
 Required properties:
 
-  - compatible : Compatible list, must contain "fsl,imx35-spdif".
+  - compatible		: Compatible list, must contain "fsl,imx35-spdif".
 
-  - reg : Offset and length of the register set for the device.
+  - reg			: Offset and length of the register set for the device.
 
-  - interrupts : Contains the spdif interrupt.
+  - interrupts		: Contains the spdif interrupt.
 
-  - dmas : Generic dma devicetree binding as described in
-  Documentation/devicetree/bindings/dma/dma.txt.
+  - dmas		: Generic dma devicetree binding as described in
+			  Documentation/devicetree/bindings/dma/dma.txt.
 
-  - dma-names : Two dmas have to be defined, "tx" and "rx".
+  - dma-names		: Two dmas have to be defined, "tx" and "rx".
 
-  - clocks : Contains an entry for each entry in clock-names.
+  - clocks		: Contains an entry for each entry in clock-names.
 
-  - clock-names : Includes the following entries:
-	"core"		The core clock of spdif controller
-	"rxtx<0-7>"	Clock source list for tx and rx clock.
-			This clock list should be identical to
-			the source list connecting to the spdif
-			clock mux in "SPDIF Transceiver Clock
-			Diagram" of SoC reference manual. It
-			can also be referred to TxClk_Source
-			bit of register SPDIF_STC.
+  - clock-names		: Includes the following entries:
+	"core"		  The core clock of spdif controller.
+	"rxtx<0-7>"	  Clock source list for tx and rx clock.
+			  This clock list should be identical to the source
+			  list connecting to the spdif clock mux in "SPDIF
+			  Transceiver Clock Diagram" of SoC reference manual.
+			  It can also be referred to TxClk_Source bit of
+			  register SPDIF_STC.
 
-   - big-endian : If this property is absent, the native endian mode will
-   be in use as default, or the big endian mode will be in use for all the
-   device registers.
+   - big-endian		: If this property is absent, the native endian mode
+			  will be in use as default, or the big endian mode
+			  will be in use for all the device registers.
 
 Example:
 

Documentation/devicetree/bindings/sound/fsl-sai.txt

@@ -5,32 +5,48 @@ which provides a synchronous audio interface that supports fullduplex
 serial interfaces with frame synchronization such as I2S, AC97, TDM, and
 codec/DSP interfaces.
 
-
 Required properties:
-- compatible: Compatible list, contains "fsl,vf610-sai" or "fsl,imx6sx-sai".
-- reg: Offset and length of the register set for the device.
-- clocks: Must contain an entry for each entry in clock-names.
-- clock-names : Must include the "bus" for register access and "mclk1" "mclk2"
-  "mclk3" for bit clock and frame clock providing.
-- dmas : Generic dma devicetree binding as described in
-  Documentation/devicetree/bindings/dma/dma.txt.
-- dma-names : Two dmas have to be defined, "tx" and "rx".
-- pinctrl-names: Must contain a "default" entry.
-- pinctrl-NNN: One property must exist for each entry in pinctrl-names.
-  See ../pinctrl/pinctrl-bindings.txt for details of the property values.
-- big-endian: Boolean property, required if all the FTM_PWM registers
-  are big-endian rather than little-endian.
-- lsb-first: Configures whether the LSB or the MSB is transmitted first for
-  the fifo data. If this property is absent, the MSB is transmitted first as
-  default, or the LSB is transmitted first.
-- fsl,sai-synchronous-rx: This is a boolean property. If present, indicating
-  that SAI will work in the synchronous mode (sync Tx with Rx) which means
-  both the transimitter and receiver will send and receive data by following
-  receiver's bit clocks and frame sync clocks.
-- fsl,sai-asynchronous: This is a boolean property. If present, indicating
-  that SAI will work in the asynchronous mode, which means both transimitter
-  and receiver will send and receive data by following their own bit clocks
-  and frame sync clocks separately.
+
+  - compatible		: Compatible list, contains "fsl,vf610-sai" or
+			  "fsl,imx6sx-sai".
+
+  - reg			: Offset and length of the register set for the device.
+
+  - clocks		: Must contain an entry for each entry in clock-names.
+
+  - clock-names		: Must include the "bus" for register access and
+			  "mclk1", "mclk2", "mclk3" for bit clock and frame
+			  clock providing.
+  - dmas		: Generic dma devicetree binding as described in
+			  Documentation/devicetree/bindings/dma/dma.txt.
+
+  - dma-names		: Two dmas have to be defined, "tx" and "rx".
+
+  - pinctrl-names	: Must contain a "default" entry.
+
+  - pinctrl-NNN		: One property must exist for each entry in
+			  pinctrl-names. See ../pinctrl/pinctrl-bindings.txt
+			  for details of the property values.
+
+  - big-endian		: Boolean property, required if all the FTM_PWM
+			  registers are big-endian rather than little-endian.
+
+  - lsb-first		: Configures whether the LSB or the MSB is transmitted
+			  first for the fifo data. If this property is absent,
+			  the MSB is transmitted first as default, or the LSB
+			  is transmitted first.
+
+  - fsl,sai-synchronous-rx: This is a boolean property. If present, indicating
+			  that SAI will work in the synchronous mode (sync Tx
+			  with Rx) which means both the transimitter and the
+			  receiver will send and receive data by following
+			  receiver's bit clocks and frame sync clocks.
+
+  - fsl,sai-asynchronous: This is a boolean property. If present, indicating
+			  that SAI will work in the asynchronous mode, which
+			  means both transimitter and receiver will send and
+			  receive data by following their own bit clocks and
+			  frame sync clocks separately.
 
 Note:
 - If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the

Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt

 Freescale i.MX audio complex with SGTL5000 codec
 
 Required properties:
-- compatible : "fsl,imx-audio-sgtl5000"
-- model : The user-visible name of this sound complex
-- ssi-controller : The phandle of the i.MX SSI controller
-- audio-codec : The phandle of the SGTL5000 audio codec
-- audio-routing : A list of the connections between audio components.
-  Each entry is a pair of strings, the first being the connection's sink,
-  the second being the connection's source. Valid names could be power
-  supplies, SGTL5000 pins, and the jacks on the board:
-
-  Power supplies:
-   * Mic Bias
-
-  SGTL5000 pins:
-   * MIC_IN
-   * LINE_IN
-   * HP_OUT
-   * LINE_OUT
-
-  Board connectors:
-   * Mic Jack
-   * Line In Jack
-   * Headphone Jack
-   * Line Out Jack
-   * Ext Spk
-
-- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX)
-- mux-ext-port : The external port of the i.MX audio muxer
+
+  - compatible		: "fsl,imx-audio-sgtl5000"
+
+  - model		: The user-visible name of this sound complex
+
+  - ssi-controller	: The phandle of the i.MX SSI controller
+
+  - audio-codec		: The phandle of the SGTL5000 audio codec
+
+  - audio-routing	: A list of the connections between audio components.
+			  Each entry is a pair of strings, the first being the
+			  connection's sink, the second being the connection's
+			  source. Valid names could be power supplies, SGTL5000
+			  pins, and the jacks on the board:
+
+			  Power supplies:
+			   * Mic Bias
+
+			  SGTL5000 pins:
+			   * MIC_IN
+			   * LINE_IN
+			   * HP_OUT
+			   * LINE_OUT
+
+			  Board connectors:
+			   * Mic Jack
+			   * Line In Jack
+			   * Headphone Jack
+			   * Line Out Jack
+			   * Ext Spk
+
+  - mux-int-port	: The internal port of the i.MX audio muxer (AUDMUX)
+
+  - mux-ext-port	: The external port of the i.MX audio muxer
 
 Note: The AUDMUX port numbering should start at 1, which is consistent with
 hardware manual.

Documentation/devicetree/bindings/sound/imx-audio-spdif.txt

@@ -2,23 +2,25 @@ Freescale i.MX audio complex with S/PDIF transceiver
 
 Required properties:
 
-  - compatible : "fsl,imx-audio-spdif"
+  - compatible		: "fsl,imx-audio-spdif"
 
-  - model : The user-visible name of this sound complex
+  - model		: The user-visible name of this sound complex
 
-  - spdif-controller : The phandle of the i.MX S/PDIF controller
+  - spdif-controller	: The phandle of the i.MX S/PDIF controller
 
 
 Optional properties:
 
-  - spdif-out : This is a boolean property. If present, the transmitting
-    function of S/PDIF will be enabled, indicating there's a physical
-    S/PDIF out connector/jack on the board or it's connecting to some
-    other IP block, such as an HDMI encoder/display-controller.
+  - spdif-out		: This is a boolean property. If present, the
+			  transmitting function of S/PDIF will be enabled,
+			  indicating there's a physical S/PDIF out connector
+			  or jack on the board or it's connecting to some
+			  other IP block, such as an HDMI encoder or
+			  display-controller.
 
-  - spdif-in : This is a boolean property. If present, the receiving
-    function of S/PDIF will be enabled, indicating there's a physical
-    S/PDIF in connector/jack on the board.
+  - spdif-in		: This is a boolean property. If present, the receiving
+			  function of S/PDIF will be enabled, indicating there
+			  is a physical S/PDIF in connector/jack on the board.
 
 * Note: At least one of these two properties should be set in the DT binding.
 

Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt

 Freescale i.MX audio complex with WM8962 codec
 
 Required properties:
-- compatible : "fsl,imx-audio-wm8962"
-- model : The user-visible name of this sound complex
-- ssi-controller : The phandle of the i.MX SSI controller
-- audio-codec : The phandle of the WM8962 audio codec
-- audio-routing : A list of the connections between audio components.
-  Each entry is a pair of strings, the first being the connection's sink,
-  the second being the connection's source. Valid names could be power
-  supplies, WM8962 pins, and the jacks on the board:
-
-  Power supplies:
-   * Mic Bias
-
-  Board connectors:
-   * Mic Jack
-   * Headphone Jack
-   * Ext Spk
-
-- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX)
-- mux-ext-port : The external port of the i.MX audio muxer
+
+  - compatible		: "fsl,imx-audio-wm8962"
+
+  - model		: The user-visible name of this sound complex
+
+  - ssi-controller	: The phandle of the i.MX SSI controller
+
+  - audio-codec		: The phandle of the WM8962 audio codec
+
+  - audio-routing	: A list of the connections between audio components.
+			  Each entry is a pair of strings, the first being the
+			  connection's sink, the second being the connection's
+			  source. Valid names could be power supplies, WM8962
+			  pins, and the jacks on the board:
+
+			  Power supplies:
+			   * Mic Bias
+
+			  Board connectors:
+			   * Mic Jack
+			   * Headphone Jack
+			   * Ext Spk
+
+  - mux-int-port	: The internal port of the i.MX audio muxer (AUDMUX)
+
+  - mux-ext-port	: The external port of the i.MX audio muxer
 
 Note: The AUDMUX port numbering should start at 1, which is consistent with
 hardware manual.

Documentation/devicetree/bindings/sound/imx-audmux.txt

 Freescale Digital Audio Mux (AUDMUX) device
 
 Required properties:
-- compatible : "fsl,imx21-audmux" for AUDMUX version firstly used on i.MX21,
-  or "fsl,imx31-audmux" for the version firstly used on i.MX31.
-- reg : Should contain AUDMUX registers location and length
+
+  - compatible		: "fsl,imx21-audmux" for AUDMUX version firstly used
+			  on i.MX21, or "fsl,imx31-audmux" for the version
+			  firstly used on i.MX31.
+
+  - reg			: Should contain AUDMUX registers location and length.
 
 An initial configuration can be setup using child nodes.
 
 Required properties of optional child nodes:
-- fsl,audmux-port : Integer of the audmux port that is configured by this
-  child node.
-- fsl,port-config : List of configuration options for the specific port. For
-  imx31-audmux and above, it is a list of tuples <ptcr pdcr>. For
-  imx21-audmux it is a list of pcr values.
+
+  - fsl,audmux-port	: Integer of the audmux port that is configured by this
+			  child node.
+
+  - fsl,port-config	: List of configuration options for the specific port.
+			  For imx31-audmux and above, it is a list of tuples
+			  <ptcr pdcr>. For imx21-audmux it is a list of pcr
+			  values.
 
 Example:
 

sound/soc/fsl/eukrea-tlv320.c

@@ -105,7 +105,7 @@ static int eukrea_tlv320_probe(struct platform_device *pdev)
 	int ret;
 	int int_port = 0, ext_port;
 	struct device_node *np = pdev->dev.of_node;
-	struct device_node *ssi_np, *codec_np;
+	struct device_node *ssi_np = NULL, *codec_np = NULL;
 
 	eukrea_tlv320.dev = &pdev->dev;
 	if (np) {
@@ -217,8 +217,7 @@ static int eukrea_tlv320_probe(struct platform_device *pdev)
 err:
 	if (ret)
 		dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret);
-	if (np)
-		of_node_put(ssi_np);
+	of_node_put(ssi_np);
 
 	return ret;
 }

sound/soc/fsl/fsl-asoc-card.c

@@ -51,6 +51,7 @@ struct codec_priv {
  * @sysclk_freq[2]: SYSCLK rates for set_sysclk()
  * @sysclk_dir[2]: SYSCLK directions for set_sysclk()
  * @sysclk_id[2]: SYSCLK ids for set_sysclk()
+ * @slot_width: Slot width of each frame
  *
  * Note: [1] for tx and [0] for rx
  */
@@ -58,6 +59,7 @@ struct cpu_priv {
 	unsigned long sysclk_freq[2];
 	u32 sysclk_dir[2];
 	u32 sysclk_id[2];
+	u32 slot_width;
 };
 
 /**
@@ -125,7 +127,12 @@ static int fsl_asoc_card_hw_params(struct snd_pcm_substream *substream,
 	priv->sample_rate = params_rate(params);
 	priv->sample_format = params_format(params);
 
-	if (priv->card.set_bias_level)
+	/*
+	 * If codec-dai is DAI Master and all configurations are already in the
+	 * set_bias_level(), bypass the remaining settings in hw_params().
+	 * Note: (dai_fmt & CBM_CFM) includes CBM_CFM and CBM_CFS.
+	 */
+	if (priv->card.set_bias_level && priv->dai_fmt & SND_SOC_DAIFMT_CBM_CFM)
 		return 0;
 
 	/* Specific configurations of DAIs starts from here */
@@ -137,6 +144,15 @@ static int fsl_asoc_card_hw_params(struct snd_pcm_substream *substream,
 		return ret;
 	}
 
+	if (cpu_priv->slot_width) {
+		ret = snd_soc_dai_set_tdm_slot(rtd->cpu_dai, 0x3, 0x3, 2,
+					       cpu_priv->slot_width);
+		if (ret) {
+			dev_err(dev, "failed to set TDM slot for cpu dai\n");
+			return ret;
+		}
+	}
+
 	return 0;
 }
 
@@ -448,6 +464,7 @@ static int fsl_asoc_card_probe(struct platform_device *pdev)
 		priv->cpu_priv.sysclk_freq[RX] = priv->codec_priv.mclk_freq;
 		priv->cpu_priv.sysclk_dir[TX] = SND_SOC_CLOCK_OUT;
 		priv->cpu_priv.sysclk_dir[RX] = SND_SOC_CLOCK_OUT;
+		priv->cpu_priv.slot_width = 32;
 		priv->dai_fmt |= SND_SOC_DAIFMT_CBS_CFS;
 	} else if (of_device_is_compatible(np, "fsl,imx-audio-sgtl5000")) {
 		priv->codec_priv.mclk_id = SGTL5000_SYSCLK;

sound/soc/fsl/fsl_ssi.c

@@ -67,8 +67,6 @@
 /**
  * FSLSSI_I2S_FORMATS: audio formats supported by the SSI
  *
- * This driver currently only supports the SSI running in I2S slave mode.
- *
  * The SSI has a limitation in that the samples must be in the same byte
  * order as the host CPU.  This is because when multiple bytes are written
  * to the STX register, the bytes and bits must be written in the same
@@ -1363,7 +1361,7 @@ static int fsl_ssi_probe(struct platform_device *pdev)
 		return PTR_ERR(ssi_private->regs);
 	}
 
-	ssi_private->irq = irq_of_parse_and_map(np, 0);
+	ssi_private->irq = platform_get_irq(pdev, 0);
 	if (!ssi_private->irq) {
 		dev_err(&pdev->dev, "no irq for node %s\n", np->full_name);
 		return -ENXIO;
@@ -1389,7 +1387,7 @@ static int fsl_ssi_probe(struct platform_device *pdev)
 	if (ssi_private->soc->imx) {
 		ret = fsl_ssi_imx_probe(pdev, ssi_private, iomem);
 		if (ret)
-			goto error_irqmap;
+			return ret;
 	}
 
 	ret = snd_soc_register_component(&pdev->dev, &fsl_ssi_component,
@@ -1412,7 +1410,7 @@ static int fsl_ssi_probe(struct platform_device *pdev)
 
 	ret = fsl_ssi_debugfs_create(&ssi_private->dbg_stats, &pdev->dev);
 	if (ret)
-		goto error_asoc_register;
+		goto error_irq;
 
 	/*
 	 * If codec-handle property is missing from SSI node, we assume
@@ -1460,10 +1458,6 @@ static int fsl_ssi_probe(struct platform_device *pdev)
 	if (ssi_private->soc->imx)
 		fsl_ssi_imx_clean(pdev, ssi_private);
 
-error_irqmap:
-	if (ssi_private->use_dma)
-		irq_dispose_mapping(ssi_private->irq);
-
 	return ret;
 }
 
@@ -1480,9 +1474,6 @@ static int fsl_ssi_remove(struct platform_device *pdev)
 	if (ssi_private->soc->imx)
 		fsl_ssi_imx_clean(pdev, ssi_private);
 
-	if (ssi_private->use_dma)
-		irq_dispose_mapping(ssi_private->irq);
-
 	return 0;
 }
 

sound/soc/fsl/imx-sgtl5000.c

@@ -175,10 +175,8 @@ static int imx_sgtl5000_probe(struct platform_device *pdev)
 fail:
 	if (data && !IS_ERR(data->codec_clk))
 		clk_put(data->codec_clk);
-	if (ssi_np)
-		of_node_put(ssi_np);
-	if (codec_np)
-		of_node_put(codec_np);
+	of_node_put(ssi_np);
+	of_node_put(codec_np);
 
 	return ret;
 }

sound/soc/fsl/imx-spdif.c

@@ -74,8 +74,7 @@ static int imx_spdif_audio_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, data);
 
 end:
-	if (spdif_np)
-		of_node_put(spdif_np);
+	of_node_put(spdif_np);
 
 	return ret;
 }

sound/soc/fsl/imx-wm8962.c

@@ -281,10 +281,8 @@ static int imx_wm8962_probe(struct platform_device *pdev)
 clk_fail:
 	clk_disable_unprepare(data->codec_clk);
 fail:
-	if (ssi_np)
-		of_node_put(ssi_np);
-	if (codec_np)
-		of_node_put(codec_np);
+	of_node_put(ssi_np);
+	of_node_put(codec_np);
 
 	return ret;
 }