bnx2x: Enhance SFP+ module control

Add flexible support to control various SFP+ module features either throughout MDIO registers or GPIO pins according to NVRAM configuration
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/bnx2x/bnx2x_hsi.h

@@ -237,8 +237,26 @@ struct port_hw_cfg {			    /* port 0: 0x12c  port 1: 0x2bc */
 #define PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_SHIFT	      16
 
 
-	u32 Reserved0[16];				    /* 0x158 */
-
+	u32 Reserved0[3];				    /* 0x158 */
+	/*	Controls the TX laser of the SFP+ module */
+	u32 sfp_ctrl;					/* 0x164 */
+#define PORT_HW_CFG_TX_LASER_MASK			      0x000000FF
+#define PORT_HW_CFG_TX_LASER_SHIFT			      0
+#define PORT_HW_CFG_TX_LASER_MDIO			      0x00000000
+#define PORT_HW_CFG_TX_LASER_GPIO0			      0x00000001
+#define PORT_HW_CFG_TX_LASER_GPIO1			      0x00000002
+#define PORT_HW_CFG_TX_LASER_GPIO2			      0x00000003
+#define PORT_HW_CFG_TX_LASER_GPIO3			      0x00000004
+
+    /*	Controls the fault module LED of the SFP+ */
+#define PORT_HW_CFG_FAULT_MODULE_LED_MASK		      0x0000FF00
+#define PORT_HW_CFG_FAULT_MODULE_LED_SHIFT		      8
+#define PORT_HW_CFG_FAULT_MODULE_LED_GPIO0		      0x00000000
+#define PORT_HW_CFG_FAULT_MODULE_LED_GPIO1		      0x00000100
+#define PORT_HW_CFG_FAULT_MODULE_LED_GPIO2		      0x00000200
+#define PORT_HW_CFG_FAULT_MODULE_LED_GPIO3		      0x00000300
+#define PORT_HW_CFG_FAULT_MODULE_LED_DISABLED		      0x00000400
+	u32 Reserved01[12];				    /* 0x158 */
 	/*  for external PHY, or forced mode or during AN */
 	u16 xgxs_config_rx[4];				    /* 0x198 */
 
@@ -246,6 +264,66 @@ struct port_hw_cfg {			    /* port 0: 0x12c  port 1: 0x2bc */
 
 	u32 Reserved1[56];				    /* 0x1A8 */
 	u32 default_cfg;				    /* 0x288 */
+#define PORT_HW_CFG_GPIO0_CONFIG_MASK			      0x00000003
+#define PORT_HW_CFG_GPIO0_CONFIG_SHIFT			      0
+#define PORT_HW_CFG_GPIO0_CONFIG_NA			      0x00000000
+#define PORT_HW_CFG_GPIO0_CONFIG_LOW			      0x00000001
+#define PORT_HW_CFG_GPIO0_CONFIG_HIGH			      0x00000002
+#define PORT_HW_CFG_GPIO0_CONFIG_INPUT			      0x00000003
+
+#define PORT_HW_CFG_GPIO1_CONFIG_MASK			      0x0000000C
+#define PORT_HW_CFG_GPIO1_CONFIG_SHIFT			      2
+#define PORT_HW_CFG_GPIO1_CONFIG_NA			      0x00000000
+#define PORT_HW_CFG_GPIO1_CONFIG_LOW			      0x00000004
+#define PORT_HW_CFG_GPIO1_CONFIG_HIGH			      0x00000008
+#define PORT_HW_CFG_GPIO1_CONFIG_INPUT			      0x0000000c
+
+#define PORT_HW_CFG_GPIO2_CONFIG_MASK			      0x00000030
+#define PORT_HW_CFG_GPIO2_CONFIG_SHIFT			      4
+#define PORT_HW_CFG_GPIO2_CONFIG_NA			      0x00000000
+#define PORT_HW_CFG_GPIO2_CONFIG_LOW			      0x00000010
+#define PORT_HW_CFG_GPIO2_CONFIG_HIGH			      0x00000020
+#define PORT_HW_CFG_GPIO2_CONFIG_INPUT			      0x00000030
+
+#define PORT_HW_CFG_GPIO3_CONFIG_MASK			      0x000000C0
+#define PORT_HW_CFG_GPIO3_CONFIG_SHIFT			      6
+#define PORT_HW_CFG_GPIO3_CONFIG_NA			      0x00000000
+#define PORT_HW_CFG_GPIO3_CONFIG_LOW			      0x00000040
+#define PORT_HW_CFG_GPIO3_CONFIG_HIGH			      0x00000080
+#define PORT_HW_CFG_GPIO3_CONFIG_INPUT			      0x000000c0
+
+	/*
+	 * When KR link is required to be set to force which is not
+	 * KR-compliant, this parameter determine what is the trigger for it.
+	 * When GPIO is selected, low input will force the speed. Currently
+	 * default speed is 1G. In the future, it may be widen to select the
+	 * forced speed in with another parameter. Note when force-1G is
+	 * enabled, it override option 56: Link Speed option.
+	 */
+#define PORT_HW_CFG_FORCE_KR_ENABLER_MASK		      0x00000F00
+#define PORT_HW_CFG_FORCE_KR_ENABLER_SHIFT		      8
+#define PORT_HW_CFG_FORCE_KR_ENABLER_NOT_FORCED		      0x00000000
+#define PORT_HW_CFG_FORCE_KR_ENABLER_GPIO0_P0		      0x00000100
+#define PORT_HW_CFG_FORCE_KR_ENABLER_GPIO1_P0		      0x00000200
+#define PORT_HW_CFG_FORCE_KR_ENABLER_GPIO2_P0		      0x00000300
+#define PORT_HW_CFG_FORCE_KR_ENABLER_GPIO3_P0		      0x00000400
+#define PORT_HW_CFG_FORCE_KR_ENABLER_GPIO0_P1		      0x00000500
+#define PORT_HW_CFG_FORCE_KR_ENABLER_GPIO1_P1		      0x00000600
+#define PORT_HW_CFG_FORCE_KR_ENABLER_GPIO2_P1		      0x00000700
+#define PORT_HW_CFG_FORCE_KR_ENABLER_GPIO3_P1		      0x00000800
+#define PORT_HW_CFG_FORCE_KR_ENABLER_FORCED		      0x00000900
+    /*	Enable to determine with which GPIO to reset the external phy */
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_MASK		      0x000F0000
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_SHIFT		      16
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_PHY_TYPE		      0x00000000
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P0		      0x00010000
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P0		      0x00020000
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P0		      0x00030000
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P0		      0x00040000
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P1		      0x00050000
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P1		      0x00060000
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P1		      0x00070000
+#define PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P1		      0x00080000
 	/*  Enable BAM on KR */
 #define PORT_HW_CFG_ENABLE_BAM_ON_KR_MASK		      0x00100000
 #define PORT_HW_CFG_ENABLE_BAM_ON_KR_SHIFT		      20

drivers/net/bnx2x/bnx2x_reg.h

@@ -6083,6 +6083,7 @@ Theotherbitsarereservedandshouldbezero*/
 #define MDIO_PMA_REG_8727_PCS_OPT_CTRL		0xc808
 #define MDIO_PMA_REG_8727_GPIO_CTRL		0xc80e
 #define MDIO_PMA_REG_8727_PCS_GP		0xc842
+#define MDIO_PMA_REG_8727_OPT_CFG_REG		0xc8e4
 
 #define MDIO_AN_REG_8727_MISC_CTRL		0x8309