Commit ab70e586 authored by jpinto's avatar jpinto Committed by David S. Miller

stmicro: add more information to Kconfig

This patch adds more info to stmicro' Kconfig files in order to be clearer
that the driver can be used by ethernet cards based on 10/100/1000/EQOS
Synopsys IP Cores.

EQOS was also added stmmac/Kconfig Kconfig, since dwmac4 is in fact EQoS,
one of Synopsys Ethernet IPs. More info at:
https://www.synopsys.com/dw/ipdir.php?ds=dwc_ether_qosSigned-off-by: default avatarJoao Pinto <jpinto@synopsys.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent d8bec2b2
...@@ -7,7 +7,8 @@ config NET_VENDOR_STMICRO ...@@ -7,7 +7,8 @@ config NET_VENDOR_STMICRO
default y default y
depends on HAS_IOMEM depends on HAS_IOMEM
---help--- ---help---
If you have a network (Ethernet) card belonging to this class, say Y. If you have a network (Ethernet) card based on Synopsys Ethernet IP
Cores, say Y.
Note that the answer to this question doesn't directly affect the Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all kernel: saying N will just cause the configurator to skip all
......
config STMMAC_ETH config STMMAC_ETH
tristate "STMicroelectronics 10/100/1000 Ethernet driver" tristate "STMicroelectronics 10/100/1000/EQOS Ethernet driver"
depends on HAS_IOMEM && HAS_DMA depends on HAS_IOMEM && HAS_DMA
select MII select MII
select PHYLIB select PHYLIB
...@@ -7,9 +7,8 @@ config STMMAC_ETH ...@@ -7,9 +7,8 @@ config STMMAC_ETH
imply PTP_1588_CLOCK imply PTP_1588_CLOCK
select RESET_CONTROLLER select RESET_CONTROLLER
---help--- ---help---
This is the driver for the Ethernet IPs are built around a This is the driver for the Ethernet IPs built around a
Synopsys IP Core and only tested on the STMicroelectronics Synopsys IP Core.
platforms.
if STMMAC_ETH if STMMAC_ETH
...@@ -152,11 +151,11 @@ config STMMAC_PCI ...@@ -152,11 +151,11 @@ config STMMAC_PCI
tristate "STMMAC PCI bus support" tristate "STMMAC PCI bus support"
depends on STMMAC_ETH && PCI depends on STMMAC_ETH && PCI
---help--- ---help---
This is to select the Synopsys DWMAC available on PCI devices, This selects the platform specific bus support for the stmmac driver.
if you have a controller with this interface, say Y or M here. This driver was tested on XLINX XC2V3000 FF1152AMT0221
D1215994A VIRTEX FPGA board and SNPS QoS IPK Prototyping Kit.
This PCI support is tested on XLINX XC2V3000 FF1152AMT0221 If you have a controller with this interface, say Y or M here.
D1215994A VIRTEX FPGA board.
If unsure, say N. If unsure, say N.
endif endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment