Skip to content

L
linux
Commit ab9aad57 authored by Shawn Guo's avatar Shawn Guo
Browse files
Options

ARM: mxs: remove board files 

Since DT kernel provides the equivalent support with those board
files, we can remove them now.
Signed-off-by: default avatarShawn Guo <shawn.guo@linaro.org>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
parent 44ffb78f
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 0 additions and 1883 deletions
arch/arm/configs/mxs_defconfig
View file @ ab9aad57
......@@ -23,12 +23,6 @@ CONFIG_BLK_DEV_INTEGRITY=y
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_MXS=y
CONFIG_MACH_MXS_DT=y
CONFIG_MACH_MX23EVK=y
CONFIG_MACH_MX28EVK=y
CONFIG_MACH_STMP378X_DEVB=y
CONFIG_MACH_TX28=y
CONFIG_MACH_M28EVK=y
CONFIG_MACH_APX4DEVKIT=y
# CONFIG_ARM_THUMB is not set
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
......
arch/arm/mach-mxs/Kconfig
View file @ ab9aad57
......@@ -27,91 +27,4 @@ config MACH_MXS_DT
Include support for Freescale MXS platforms(i.MX23 and i.MX28)
using the device tree for discovery
config MACH_STMP378X_DEVB
bool "Support STMP378x_devb Platform"
select SOC_IMX23
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_RTC_STMP3XXX
help
Include support for STMP378x-devb platform. This includes specific
configurations for the board and its peripherals.
config MACH_MX23EVK
bool "Support MX23EVK Platform"
select SOC_IMX23
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXSFB
select MXS_HAVE_PLATFORM_RTC_STMP3XXX
help
Include support for MX23EVK platform. This includes specific
configurations for the board and its peripherals.
config MACH_MX28EVK
bool "Support MX28EVK Platform"
select SOC_IMX28
select LEDS_GPIO_REGISTER
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_FEC
select MXS_HAVE_PLATFORM_FLEXCAN
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXSFB
select MXS_HAVE_PLATFORM_MXS_SAIF
select MXS_HAVE_PLATFORM_MXS_I2C
select MXS_HAVE_PLATFORM_RTC_STMP3XXX
help
Include support for MX28EVK platform. This includes specific
configurations for the board and its peripherals.
config MODULE_TX28
bool
select SOC_IMX28
select LEDS_GPIO_REGISTER
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_FEC
select MXS_HAVE_PLATFORM_MXS_I2C
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXS_PWM
select MXS_HAVE_PLATFORM_RTC_STMP3XXX
config MODULE_M28
bool
select SOC_IMX28
select LEDS_GPIO_REGISTER
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_FEC
select MXS_HAVE_PLATFORM_FLEXCAN
select MXS_HAVE_PLATFORM_MXS_I2C
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXSFB
config MODULE_APX4
bool
select SOC_IMX28
select LEDS_GPIO_REGISTER
select MXS_HAVE_AMBA_DUART
select MXS_HAVE_PLATFORM_AUART
select MXS_HAVE_PLATFORM_FEC
select MXS_HAVE_PLATFORM_MXS_I2C
select MXS_HAVE_PLATFORM_MXS_MMC
select MXS_HAVE_PLATFORM_MXS_SAIF
config MACH_TX28
bool "Ka-Ro TX28 module"
select MODULE_TX28
config MACH_M28EVK
bool "Support DENX M28EVK Platform"
select MODULE_M28
config MACH_APX4DEVKIT
bool "Support Bluegiga APX4 Development Kit"
select MODULE_APX4
endif
arch/arm/mach-mxs/Makefile
View file @ ab9aad57
......@@ -4,12 +4,5 @@ obj-y := devices.o icoll.o iomux.o ocotp.o system.o timer.o mm.o
obj-$(CONFIG_PM) += pm.o
obj-$(CONFIG_MACH_MXS_DT) += mach-mxs.o
obj-$(CONFIG_MACH_STMP378X_DEVB) += mach-stmp378x_devb.o
obj-$(CONFIG_MACH_MX23EVK) += mach-mx23evk.o
obj-$(CONFIG_MACH_MX28EVK) += mach-mx28evk.o
obj-$(CONFIG_MACH_M28EVK) += mach-m28evk.o
obj-$(CONFIG_MACH_APX4DEVKIT) += mach-apx4devkit.o
obj-$(CONFIG_MODULE_TX28) += module-tx28.o
obj-$(CONFIG_MACH_TX28) += mach-tx28.o
obj-y += devices/
arch/arm/mach-mxs/mach-apx4devkit.c deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright (C) 2011-2012
* Lauri Hintsala, Bluegiga, <lauri.hintsala@bluegiga.com>
* Veli-Pekka Peltola, Bluegiga, <veli-pekka.peltola@bluegiga.com>
*
* based on: mach-mx28evk.c
* Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/leds.h>
#include <linux/clk.h>
#include <linux/i2c.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
#include <linux/micrel_phy.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/common.h>
#include <mach/digctl.h>
#include <mach/iomux-mx28.h>
#include "devices-mx28.h"
#define APX4DEVKIT_GPIO_USERLED MXS_GPIO_NR(3, 28)
static const iomux_cfg_t apx4devkit_pads[] __initconst = {
/* duart */
MX28_PAD_PWM0__DUART_RX | MXS_PAD_CTRL,
MX28_PAD_PWM1__DUART_TX | MXS_PAD_CTRL,
/* auart0 */
MX28_PAD_AUART0_RX__AUART0_RX | MXS_PAD_CTRL,
MX28_PAD_AUART0_TX__AUART0_TX | MXS_PAD_CTRL,
MX28_PAD_AUART0_CTS__AUART0_CTS | MXS_PAD_CTRL,
MX28_PAD_AUART0_RTS__AUART0_RTS | MXS_PAD_CTRL,
/* auart1 */
MX28_PAD_AUART1_RX__AUART1_RX | MXS_PAD_CTRL,
MX28_PAD_AUART1_TX__AUART1_TX | MXS_PAD_CTRL,
/* auart2 */
MX28_PAD_SSP2_SCK__AUART2_RX | MXS_PAD_CTRL,
MX28_PAD_SSP2_MOSI__AUART2_TX | MXS_PAD_CTRL,
/* auart3 */
MX28_PAD_SSP2_MISO__AUART3_RX | MXS_PAD_CTRL,
MX28_PAD_SSP2_SS0__AUART3_TX | MXS_PAD_CTRL,
#define MXS_PAD_FEC (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP)
/* fec0 */
MX28_PAD_ENET0_MDC__ENET0_MDC | MXS_PAD_FEC,
MX28_PAD_ENET0_MDIO__ENET0_MDIO | MXS_PAD_FEC,
MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MXS_PAD_FEC,
MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MXS_PAD_FEC,
MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MXS_PAD_FEC,
MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MXS_PAD_FEC,
MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MXS_PAD_FEC,
MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MXS_PAD_FEC,
MX28_PAD_ENET_CLK__CLKCTRL_ENET | MXS_PAD_FEC,
/* i2c */
MX28_PAD_I2C0_SCL__I2C0_SCL,
MX28_PAD_I2C0_SDA__I2C0_SDA,
/* mmc0 */
MX28_PAD_SSP0_DATA0__SSP0_D0 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA1__SSP0_D1 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA2__SSP0_D2 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA3__SSP0_D3 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA4__SSP0_D4 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA5__SSP0_D5 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA6__SSP0_D6 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA7__SSP0_D7 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_CMD__SSP0_CMD |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX28_PAD_SSP0_SCK__SSP0_SCK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
/* led */
MX28_PAD_PWM3__GPIO_3_28 | MXS_PAD_CTRL,
/* saif0 & saif1 */
MX28_PAD_SAIF0_MCLK__SAIF0_MCLK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
};
/* led */
static const struct gpio_led apx4devkit_leds[] __initconst = {
{
.name = "user-led",
.default_trigger = "heartbeat",
.gpio = APX4DEVKIT_GPIO_USERLED,
},
};
static const struct gpio_led_platform_data apx4devkit_led_data __initconst = {
.leds = apx4devkit_leds,
.num_leds = ARRAY_SIZE(apx4devkit_leds),
};
static const struct fec_platform_data mx28_fec_pdata __initconst = {
.phy = PHY_INTERFACE_MODE_RMII,
};
static const struct mxs_mmc_platform_data apx4devkit_mmc_pdata __initconst = {
.wp_gpio = -EINVAL,
.flags = SLOTF_4_BIT_CAPABLE,
};
static const struct i2c_board_info apx4devkit_i2c_boardinfo[] __initconst = {
{ I2C_BOARD_INFO("sgtl5000", 0x0a) }, /* ASoC */
{ I2C_BOARD_INFO("pcf8563", 0x51) }, /* RTC */
};
#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || \
defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
static struct regulator_consumer_supply apx4devkit_audio_consumer_supplies[] = {
REGULATOR_SUPPLY("VDDA", "0-000a"),
REGULATOR_SUPPLY("VDDIO", "0-000a"),
};
static struct regulator_init_data apx4devkit_vdd_reg_init_data = {
.constraints = {
.name = "3V3",
.always_on = 1,
},
.consumer_supplies = apx4devkit_audio_consumer_supplies,
.num_consumer_supplies = ARRAY_SIZE(apx4devkit_audio_consumer_supplies),
};
static struct fixed_voltage_config apx4devkit_vdd_pdata = {
.supply_name = "board-3V3",
.microvolts = 3300000,
.gpio = -EINVAL,
.enabled_at_boot = 1,
.init_data = &apx4devkit_vdd_reg_init_data,
};
static struct platform_device apx4devkit_voltage_regulator = {
.name = "reg-fixed-voltage",
.id = -1,
.num_resources = 0,
.dev = {
.platform_data = &apx4devkit_vdd_pdata,
},
};
static void __init apx4devkit_add_regulators(void)
{
platform_device_register(&apx4devkit_voltage_regulator);
}
#else
static void __init apx4devkit_add_regulators(void) {}
#endif
static const struct mxs_saif_platform_data
apx4devkit_mxs_saif_pdata[] __initconst = {
/* working on EXTMSTR0 mode (saif0 master, saif1 slave) */
{
.master_mode = 1,
.master_id = 0,
}, {
.master_mode = 0,
.master_id = 0,
},
};
static int apx4devkit_phy_fixup(struct phy_device *phy)
{
phy->dev_flags |= MICREL_PHY_50MHZ_CLK;
return 0;
}
static void __init apx4devkit_fec_phy_clk_enable(void)
{
struct clk *clk;
/* Enable fec phy clock */
clk = clk_get_sys("enet_out", NULL);
if (!IS_ERR(clk))
clk_prepare_enable(clk);
}
static void __init apx4devkit_init(void)
{
mx28_soc_init();
mxs_iomux_setup_multiple_pads(apx4devkit_pads,
ARRAY_SIZE(apx4devkit_pads));
mx28_add_duart();
mx28_add_auart0();
mx28_add_auart1();
mx28_add_auart2();
mx28_add_auart3();
/*
* Register fixup for the Micrel KS8031 PHY clock
* (shares same ID with KS8051)
*/
phy_register_fixup_for_uid(PHY_ID_KS8051, MICREL_PHY_ID_MASK,
apx4devkit_phy_fixup);
apx4devkit_fec_phy_clk_enable();
mx28_add_fec(0, &mx28_fec_pdata);
mx28_add_mxs_mmc(0, &apx4devkit_mmc_pdata);
gpio_led_register_device(0, &apx4devkit_led_data);
mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
mx28_add_saif(0, &apx4devkit_mxs_saif_pdata[0]);
mx28_add_saif(1, &apx4devkit_mxs_saif_pdata[1]);
apx4devkit_add_regulators();
mx28_add_mxs_i2c(0);
i2c_register_board_info(0, apx4devkit_i2c_boardinfo,
ARRAY_SIZE(apx4devkit_i2c_boardinfo));
mxs_add_platform_device("mxs-sgtl5000", 0, NULL, 0, NULL, 0);
}
static void __init apx4devkit_timer_init(void)
{
mx28_clocks_init();
}
static struct sys_timer apx4devkit_timer = {
.init = apx4devkit_timer_init,
};
MACHINE_START(APX4DEVKIT, "Bluegiga APX4 Development Kit")
.map_io = mx28_map_io,
.init_irq = mx28_init_irq,
.timer = &apx4devkit_timer,
.init_machine = apx4devkit_init,
.restart = mxs_restart,
MACHINE_END
arch/arm/mach-mxs/mach-m28evk.c deleted 100644 → 0
View file @ 44ffb78f
This diff is collapsed.
arch/arm/mach-mxs/mach-mx23evk.c deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/common.h>
#include <mach/iomux-mx23.h>
#include "devices-mx23.h"
#define MX23EVK_LCD_ENABLE MXS_GPIO_NR(1, 18)
#define MX23EVK_BL_ENABLE MXS_GPIO_NR(1, 28)
#define MX23EVK_MMC0_WRITE_PROTECT MXS_GPIO_NR(1, 30)
#define MX23EVK_MMC0_SLOT_POWER MXS_GPIO_NR(1, 29)
static const iomux_cfg_t mx23evk_pads[] __initconst = {
/* duart */
MX23_PAD_PWM0__DUART_RX | MXS_PAD_CTRL,
MX23_PAD_PWM1__DUART_TX | MXS_PAD_CTRL,
/* auart */
MX23_PAD_AUART1_RX__AUART1_RX | MXS_PAD_CTRL,
MX23_PAD_AUART1_TX__AUART1_TX | MXS_PAD_CTRL,
MX23_PAD_AUART1_CTS__AUART1_CTS | MXS_PAD_CTRL,
MX23_PAD_AUART1_RTS__AUART1_RTS | MXS_PAD_CTRL,
/* mxsfb (lcdif) */
MX23_PAD_LCD_D00__LCD_D00 | MXS_PAD_CTRL,
MX23_PAD_LCD_D01__LCD_D01 | MXS_PAD_CTRL,
MX23_PAD_LCD_D02__LCD_D02 | MXS_PAD_CTRL,
MX23_PAD_LCD_D03__LCD_D03 | MXS_PAD_CTRL,
MX23_PAD_LCD_D04__LCD_D04 | MXS_PAD_CTRL,
MX23_PAD_LCD_D05__LCD_D05 | MXS_PAD_CTRL,
MX23_PAD_LCD_D06__LCD_D06 | MXS_PAD_CTRL,
MX23_PAD_LCD_D07__LCD_D07 | MXS_PAD_CTRL,
MX23_PAD_LCD_D08__LCD_D08 | MXS_PAD_CTRL,
MX23_PAD_LCD_D09__LCD_D09 | MXS_PAD_CTRL,
MX23_PAD_LCD_D10__LCD_D10 | MXS_PAD_CTRL,
MX23_PAD_LCD_D11__LCD_D11 | MXS_PAD_CTRL,
MX23_PAD_LCD_D12__LCD_D12 | MXS_PAD_CTRL,
MX23_PAD_LCD_D13__LCD_D13 | MXS_PAD_CTRL,
MX23_PAD_LCD_D14__LCD_D14 | MXS_PAD_CTRL,
MX23_PAD_LCD_D15__LCD_D15 | MXS_PAD_CTRL,
MX23_PAD_LCD_D16__LCD_D16 | MXS_PAD_CTRL,
MX23_PAD_LCD_D17__LCD_D17 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D08__LCD_D18 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D09__LCD_D19 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D10__LCD_D20 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D11__LCD_D21 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D12__LCD_D22 | MXS_PAD_CTRL,
MX23_PAD_GPMI_D13__LCD_D23 | MXS_PAD_CTRL,
MX23_PAD_LCD_VSYNC__LCD_VSYNC | MXS_PAD_CTRL,
MX23_PAD_LCD_HSYNC__LCD_HSYNC | MXS_PAD_CTRL,
MX23_PAD_LCD_DOTCK__LCD_DOTCK | MXS_PAD_CTRL,
MX23_PAD_LCD_ENABLE__LCD_ENABLE | MXS_PAD_CTRL,
/* LCD panel enable */
MX23_PAD_LCD_RESET__GPIO_1_18 | MXS_PAD_CTRL,
/* backlight control */
MX23_PAD_PWM2__GPIO_1_28 | MXS_PAD_CTRL,
/* mmc */
MX23_PAD_SSP1_DATA0__SSP1_DATA0 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA1__SSP1_DATA1 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA2__SSP1_DATA2 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA3__SSP1_DATA3 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_GPMI_D08__SSP1_DATA4 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_GPMI_D09__SSP1_DATA5 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_GPMI_D10__SSP1_DATA6 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_GPMI_D11__SSP1_DATA7 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_CMD__SSP1_CMD |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DETECT__SSP1_DETECT |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX23_PAD_SSP1_SCK__SSP1_SCK |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
/* write protect */
MX23_PAD_PWM4__GPIO_1_30 |
(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
/* slot power enable */
MX23_PAD_PWM3__GPIO_1_29 |
(MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
};
/* mxsfb (lcdif) */
static struct fb_videomode mx23evk_video_modes[] = {
{
.name = "Samsung-LMS430HF02",
.refresh = 60,
.xres = 480,
.yres = 272,
.pixclock = 108096, /* picosecond (9.2 MHz) */
.left_margin = 15,
.right_margin = 8,
.upper_margin = 12,
.lower_margin = 4,
.hsync_len = 1,
.vsync_len = 1,
.sync = FB_SYNC_DATA_ENABLE_HIGH_ACT |
FB_SYNC_DOTCLK_FAILING_ACT,
},
};
static const struct mxsfb_platform_data mx23evk_mxsfb_pdata __initconst = {
.mode_list = mx23evk_video_modes,
.mode_count = ARRAY_SIZE(mx23evk_video_modes),
.default_bpp = 32,
.ld_intf_width = STMLCDIF_24BIT,
};
static struct mxs_mmc_platform_data mx23evk_mmc_pdata __initdata = {
.wp_gpio = MX23EVK_MMC0_WRITE_PROTECT,
.flags = SLOTF_8_BIT_CAPABLE,
};
static void __init mx23evk_init(void)
{
int ret;
mx23_soc_init();
mxs_iomux_setup_multiple_pads(mx23evk_pads, ARRAY_SIZE(mx23evk_pads));
mx23_add_duart();
mx23_add_auart0();
/* power on mmc slot by writing 0 to the gpio */
ret = gpio_request_one(MX23EVK_MMC0_SLOT_POWER, GPIOF_OUT_INIT_LOW,
"mmc0-slot-power");
if (ret)
pr_warn("failed to request gpio mmc0-slot-power: %d\n", ret);
mx23_add_mxs_mmc(0, &mx23evk_mmc_pdata);
ret = gpio_request_one(MX23EVK_LCD_ENABLE, GPIOF_DIR_OUT, "lcd-enable");
if (ret)
pr_warn("failed to request gpio lcd-enable: %d\n", ret);
else
gpio_set_value(MX23EVK_LCD_ENABLE, 1);
ret = gpio_request_one(MX23EVK_BL_ENABLE, GPIOF_DIR_OUT, "bl-enable");
if (ret)
pr_warn("failed to request gpio bl-enable: %d\n", ret);
else
gpio_set_value(MX23EVK_BL_ENABLE, 1);
mx23_add_mxsfb(&mx23evk_mxsfb_pdata);
mx23_add_rtc_stmp3xxx();
}
static void __init mx23evk_timer_init(void)
{
mx23_clocks_init();
}
static struct sys_timer mx23evk_timer = {
.init = mx23evk_timer_init,
};
MACHINE_START(MX23EVK, "Freescale MX23 EVK")
/* Maintainer: Freescale Semiconductor, Inc. */
.map_io = mx23_map_io,
.init_irq = mx23_init_irq,
.timer = &mx23evk_timer,
.init_machine = mx23evk_init,
.restart = mxs_restart,
MACHINE_END
arch/arm/mach-mxs/mach-mx28evk.c deleted 100644 → 0
View file @ 44ffb78f
This diff is collapsed.
arch/arm/mach-mxs/mach-stmp378x_devb.c deleted 100644 → 0
View file @ 44ffb78f
/*
* board setup for STMP378x-Development-Board
*
* based on mx23evk board setup and information gained form the original
* plat-stmp based board setup, now converted to mach-mxs.
*
* Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
* Copyright (C) 2011 Wolfram Sang, Pengutronix e.K.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/common.h>
#include <mach/iomux-mx23.h>
#include "devices-mx23.h"
#define STMP378X_DEVB_MMC0_WRITE_PROTECT MXS_GPIO_NR(1, 30)
#define STMP378X_DEVB_MMC0_SLOT_POWER MXS_GPIO_NR(1, 29)
#define STMP378X_DEVB_PAD_AUART (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL)
static const iomux_cfg_t stmp378x_dvb_pads[] __initconst = {
/* duart (extended setup missing in old boardcode, too */
MX23_PAD_PWM0__DUART_RX,
MX23_PAD_PWM1__DUART_TX,
/* auart */
MX23_PAD_AUART1_RX__AUART1_RX | STMP378X_DEVB_PAD_AUART,
MX23_PAD_AUART1_TX__AUART1_TX | STMP378X_DEVB_PAD_AUART,
MX23_PAD_AUART1_CTS__AUART1_CTS | STMP378X_DEVB_PAD_AUART,
MX23_PAD_AUART1_RTS__AUART1_RTS | STMP378X_DEVB_PAD_AUART,
/* mmc */
MX23_PAD_SSP1_DATA0__SSP1_DATA0 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA1__SSP1_DATA1 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA2__SSP1_DATA2 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DATA3__SSP1_DATA3 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_CMD__SSP1_CMD |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX23_PAD_SSP1_DETECT__SSP1_DETECT |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX23_PAD_SSP1_SCK__SSP1_SCK |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX23_PAD_PWM4__GPIO_1_30 | MXS_PAD_CTRL, /* write protect */
MX23_PAD_PWM3__GPIO_1_29 | MXS_PAD_CTRL, /* power enable */
};
static struct mxs_mmc_platform_data stmp378x_dvb_mmc_pdata __initdata = {
.wp_gpio = STMP378X_DEVB_MMC0_WRITE_PROTECT,
};
static struct spi_board_info spi_board_info[] __initdata = {
#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
{
.modalias = "enc28j60",
.max_speed_hz = 6 * 1000 * 1000,
.bus_num = 1,
.chip_select = 0,
.platform_data = NULL,
},
#endif
};
static void __init stmp378x_dvb_init(void)
{
int ret;
mx23_soc_init();
mxs_iomux_setup_multiple_pads(stmp378x_dvb_pads,
ARRAY_SIZE(stmp378x_dvb_pads));
mx23_add_duart();
mx23_add_auart0();
mx23_add_rtc_stmp3xxx();
/* power on mmc slot */
ret = gpio_request_one(STMP378X_DEVB_MMC0_SLOT_POWER,
GPIOF_OUT_INIT_LOW, "mmc0-slot-power");
if (ret)
pr_warn("could not power mmc (%d)\n", ret);
mx23_add_mxs_mmc(0, &stmp378x_dvb_mmc_pdata);
spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
}
static void __init stmp378x_dvb_timer_init(void)
{
mx23_clocks_init();
}
static struct sys_timer stmp378x_dvb_timer = {
.init = stmp378x_dvb_timer_init,
};
MACHINE_START(STMP378X, "STMP378X")
.map_io = mx23_map_io,
.init_irq = mx23_init_irq,
.timer = &stmp378x_dvb_timer,
.init_machine = stmp378x_dvb_init,
.restart = mxs_restart,
MACHINE_END
arch/arm/mach-mxs/mach-tx28.c deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright (C) 2010 <LW@KARO-electronics.de>
*
* based on: mach-mx28_evk.c
* Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation
*/
#include <linux/kernel.h>
#include <linux/gpio.h>
#include <linux/leds.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_gpio.h>
#include <linux/i2c.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <mach/common.h>
#include <mach/iomux-mx28.h>
#include "devices-mx28.h"
#include "module-tx28.h"
#define TX28_STK5_GPIO_LED MXS_GPIO_NR(4, 10)
static const iomux_cfg_t tx28_stk5v3_pads[] __initconst = {
/* LED */
MX28_PAD_ENET0_RXD3__GPIO_4_10 |
MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_NOPULL,
/* framebuffer */
#define LCD_MODE (MXS_PAD_3V3 | MXS_PAD_4MA)
MX28_PAD_LCD_D00__LCD_D0 | LCD_MODE,
MX28_PAD_LCD_D01__LCD_D1 | LCD_MODE,
MX28_PAD_LCD_D02__LCD_D2 | LCD_MODE,
MX28_PAD_LCD_D03__LCD_D3 | LCD_MODE,
MX28_PAD_LCD_D04__LCD_D4 | LCD_MODE,
MX28_PAD_LCD_D05__LCD_D5 | LCD_MODE,
MX28_PAD_LCD_D06__LCD_D6 | LCD_MODE,
MX28_PAD_LCD_D07__LCD_D7 | LCD_MODE,
MX28_PAD_LCD_D08__LCD_D8 | LCD_MODE,
MX28_PAD_LCD_D09__LCD_D9 | LCD_MODE,
MX28_PAD_LCD_D10__LCD_D10 | LCD_MODE,
MX28_PAD_LCD_D11__LCD_D11 | LCD_MODE,
MX28_PAD_LCD_D12__LCD_D12 | LCD_MODE,
MX28_PAD_LCD_D13__LCD_D13 | LCD_MODE,
MX28_PAD_LCD_D14__LCD_D14 | LCD_MODE,
MX28_PAD_LCD_D15__LCD_D15 | LCD_MODE,
MX28_PAD_LCD_D16__LCD_D16 | LCD_MODE,
MX28_PAD_LCD_D17__LCD_D17 | LCD_MODE,
MX28_PAD_LCD_D18__LCD_D18 | LCD_MODE,
MX28_PAD_LCD_D19__LCD_D19 | LCD_MODE,
MX28_PAD_LCD_D20__LCD_D20 | LCD_MODE,
MX28_PAD_LCD_D21__LCD_D21 | LCD_MODE,
MX28_PAD_LCD_D22__LCD_D22 | LCD_MODE,
MX28_PAD_LCD_D23__LCD_D23 | LCD_MODE,
MX28_PAD_LCD_RD_E__LCD_VSYNC | LCD_MODE,
MX28_PAD_LCD_WR_RWN__LCD_HSYNC | LCD_MODE,
MX28_PAD_LCD_RS__LCD_DOTCLK | LCD_MODE,
MX28_PAD_LCD_CS__LCD_CS | LCD_MODE,
MX28_PAD_LCD_VSYNC__LCD_VSYNC | LCD_MODE,
MX28_PAD_LCD_HSYNC__LCD_HSYNC | LCD_MODE,
MX28_PAD_LCD_DOTCLK__LCD_DOTCLK | LCD_MODE,
MX28_PAD_LCD_ENABLE__GPIO_1_31 | LCD_MODE,
MX28_PAD_LCD_RESET__GPIO_3_30 | LCD_MODE,
MX28_PAD_PWM0__PWM_0 | LCD_MODE,
/* UART1 */
MX28_PAD_AUART0_CTS__DUART_RX,
MX28_PAD_AUART0_RTS__DUART_TX,
MX28_PAD_AUART0_TX__DUART_RTS,
MX28_PAD_AUART0_RX__DUART_CTS,
/* UART2 */
MX28_PAD_AUART1_RX__AUART1_RX,
MX28_PAD_AUART1_TX__AUART1_TX,
MX28_PAD_AUART1_RTS__AUART1_RTS,
MX28_PAD_AUART1_CTS__AUART1_CTS,
/* CAN */
MX28_PAD_GPMI_RDY2__CAN0_TX,
MX28_PAD_GPMI_RDY3__CAN0_RX,
/* I2C */
MX28_PAD_I2C0_SCL__I2C0_SCL,
MX28_PAD_I2C0_SDA__I2C0_SDA,
/* TSC2007 */
MX28_PAD_SAIF0_MCLK__GPIO_3_20 | MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP,
/* MMC0 */
MX28_PAD_SSP0_DATA0__SSP0_D0 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA1__SSP0_D1 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA2__SSP0_D2 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DATA3__SSP0_D3 |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_CMD__SSP0_CMD |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
(MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
MX28_PAD_SSP0_SCK__SSP0_SCK |
(MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
};
static const struct gpio_led tx28_stk5v3_leds[] __initconst = {
{
.name = "GPIO-LED",
.default_trigger = "heartbeat",
.gpio = TX28_STK5_GPIO_LED,
},
};
static const struct gpio_led_platform_data tx28_stk5v3_led_data __initconst = {
.leds = tx28_stk5v3_leds,
.num_leds = ARRAY_SIZE(tx28_stk5v3_leds),
};
static struct spi_board_info tx28_spi_board_info[] = {
{
.modalias = "spidev",
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 1,
.controller_data = (void *)SPI_GPIO_NO_CHIPSELECT,
.mode = SPI_MODE_0,
},
};
static struct i2c_board_info tx28_stk5v3_i2c_boardinfo[] __initdata = {
{
I2C_BOARD_INFO("ds1339", 0x68),
},
};
static struct mxs_mmc_platform_data tx28_mmc0_pdata __initdata = {
.wp_gpio = -EINVAL,
.flags = SLOTF_4_BIT_CAPABLE,
};
static void __init tx28_stk5v3_init(void)
{
mx28_soc_init();
mxs_iomux_setup_multiple_pads(tx28_stk5v3_pads,
ARRAY_SIZE(tx28_stk5v3_pads));
mx28_add_duart(); /* UART1 */
mx28_add_auart(1); /* UART2 */
tx28_add_fec0();
/* spi via ssp will be added when available */
spi_register_board_info(tx28_spi_board_info,
ARRAY_SIZE(tx28_spi_board_info));
gpio_led_register_device(0, &tx28_stk5v3_led_data);
mx28_add_mxs_i2c(0);
i2c_register_board_info(0, tx28_stk5v3_i2c_boardinfo,
ARRAY_SIZE(tx28_stk5v3_i2c_boardinfo));
mx28_add_mxs_mmc(0, &tx28_mmc0_pdata);
mx28_add_rtc_stmp3xxx();
}
static void __init tx28_timer_init(void)
{
mx28_clocks_init();
}
static struct sys_timer tx28_timer = {
.init = tx28_timer_init,
};
MACHINE_START(TX28, "Ka-Ro electronics TX28 module")
.map_io = mx28_map_io,
.init_irq = mx28_init_irq,
.timer = &tx28_timer,
.init_machine = tx28_stk5v3_init,
.restart = mxs_restart,
MACHINE_END
arch/arm/mach-mxs/module-tx28.c deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright (C) 2010 <LW@KARO-electronics.de>
*
* This program is free software; you can redistribute it and/or modify it under
* the terms of the GNU General Public License version 2 as published by the
* Free Software Foundation.
*/
#include <linux/delay.h>
#include <linux/fec.h>
#include <linux/gpio.h>
#include <mach/iomux-mx28.h>
#include "devices-mx28.h"
#include "module-tx28.h"
#define TX28_FEC_PHY_POWER MXS_GPIO_NR(3, 29)
#define TX28_FEC_PHY_RESET MXS_GPIO_NR(4, 13)
static const iomux_cfg_t tx28_fec_gpio_pads[] __initconst = {
/* PHY POWER */
MX28_PAD_PWM4__GPIO_3_29 |
MXS_PAD_4MA | MXS_PAD_NOPULL | MXS_PAD_3V3,
/* PHY RESET */
MX28_PAD_ENET0_RX_CLK__GPIO_4_13 |
MXS_PAD_4MA | MXS_PAD_NOPULL | MXS_PAD_3V3,
/* Mode strap pins 0-2 */
MX28_PAD_ENET0_RXD0__GPIO_4_3 |
MXS_PAD_8MA | MXS_PAD_PULLUP | MXS_PAD_3V3,
MX28_PAD_ENET0_RXD1__GPIO_4_4 |
MXS_PAD_8MA | MXS_PAD_PULLUP | MXS_PAD_3V3,
MX28_PAD_ENET0_RX_EN__GPIO_4_2 |
MXS_PAD_8MA | MXS_PAD_PULLUP | MXS_PAD_3V3,
/* nINT */
MX28_PAD_ENET0_TX_CLK__GPIO_4_5 |
MXS_PAD_4MA | MXS_PAD_NOPULL | MXS_PAD_3V3,
MX28_PAD_ENET0_MDC__GPIO_4_0,
MX28_PAD_ENET0_MDIO__GPIO_4_1,
MX28_PAD_ENET0_TX_EN__GPIO_4_6,
MX28_PAD_ENET0_TXD0__GPIO_4_7,
MX28_PAD_ENET0_TXD1__GPIO_4_8,
MX28_PAD_ENET_CLK__GPIO_4_16,
};
#define FEC_MODE (MXS_PAD_8MA | MXS_PAD_PULLUP | MXS_PAD_3V3)
static const iomux_cfg_t tx28_fec0_pads[] __initconst = {
MX28_PAD_ENET0_MDC__ENET0_MDC | FEC_MODE,
MX28_PAD_ENET0_MDIO__ENET0_MDIO | FEC_MODE,
MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | FEC_MODE,
MX28_PAD_ENET0_RXD0__ENET0_RXD0 | FEC_MODE,
MX28_PAD_ENET0_RXD1__ENET0_RXD1 | FEC_MODE,
MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | FEC_MODE,
MX28_PAD_ENET0_TXD0__ENET0_TXD0 | FEC_MODE,
MX28_PAD_ENET0_TXD1__ENET0_TXD1 | FEC_MODE,
MX28_PAD_ENET_CLK__CLKCTRL_ENET | FEC_MODE,
};
static const iomux_cfg_t tx28_fec1_pads[] __initconst = {
MX28_PAD_ENET0_RXD2__ENET1_RXD0,
MX28_PAD_ENET0_RXD3__ENET1_RXD1,
MX28_PAD_ENET0_TXD2__ENET1_TXD0,
MX28_PAD_ENET0_TXD3__ENET1_TXD1,
MX28_PAD_ENET0_COL__ENET1_TX_EN,
MX28_PAD_ENET0_CRS__ENET1_RX_EN,
};
static const struct fec_platform_data tx28_fec0_data __initconst = {
.phy = PHY_INTERFACE_MODE_RMII,
};
static const struct fec_platform_data tx28_fec1_data __initconst = {
.phy = PHY_INTERFACE_MODE_RMII,
};
int __init tx28_add_fec0(void)
{
int i, ret;
pr_debug("%s: Switching FEC PHY power off\n", __func__);
ret = mxs_iomux_setup_multiple_pads(tx28_fec_gpio_pads,
ARRAY_SIZE(tx28_fec_gpio_pads));
for (i = 0; i < ARRAY_SIZE(tx28_fec_gpio_pads); i++) {
unsigned int gpio = MXS_GPIO_NR(PAD_BANK(tx28_fec_gpio_pads[i]),
PAD_PIN(tx28_fec_gpio_pads[i]));
ret = gpio_request(gpio, "FEC");
if (ret) {
pr_err("Failed to request GPIO_%d_%d: %d\n",
PAD_BANK(tx28_fec_gpio_pads[i]),
PAD_PIN(tx28_fec_gpio_pads[i]), ret);
goto free_gpios;
}
ret = gpio_direction_output(gpio, 0);
if (ret) {
pr_err("Failed to set direction of GPIO_%d_%d to output: %d\n",
gpio / 32 + 1, gpio % 32, ret);
goto free_gpios;
}
}
/* Power up fec phy */
pr_debug("%s: Switching FEC PHY power on\n", __func__);
ret = gpio_direction_output(TX28_FEC_PHY_POWER, 1);
if (ret) {
pr_err("Failed to power on PHY: %d\n", ret);
goto free_gpios;
}
mdelay(26); /* 25ms according to data sheet */
/* nINT */
gpio_direction_input(MXS_GPIO_NR(4, 5));
/* Mode strap pins */
gpio_direction_output(MXS_GPIO_NR(4, 2), 1);
gpio_direction_output(MXS_GPIO_NR(4, 3), 1);
gpio_direction_output(MXS_GPIO_NR(4, 4), 1);
udelay(100); /* minimum assertion time for nRST */
pr_debug("%s: Deasserting FEC PHY RESET\n", __func__);
gpio_set_value(TX28_FEC_PHY_RESET, 1);
ret = mxs_iomux_setup_multiple_pads(tx28_fec0_pads,
ARRAY_SIZE(tx28_fec0_pads));
if (ret) {
pr_debug("%s: mxs_iomux_setup_multiple_pads() failed with rc: %d\n",
__func__, ret);
goto free_gpios;
}
pr_debug("%s: Registering FEC0 device\n", __func__);
mx28_add_fec(0, &tx28_fec0_data);
return 0;
free_gpios:
while (--i >= 0) {
unsigned int gpio = MXS_GPIO_NR(PAD_BANK(tx28_fec_gpio_pads[i]),
PAD_PIN(tx28_fec_gpio_pads[i]));
gpio_free(gpio);
}
return ret;
}
int __init tx28_add_fec1(void)
{
int ret;
ret = mxs_iomux_setup_multiple_pads(tx28_fec1_pads,
ARRAY_SIZE(tx28_fec1_pads));
if (ret) {
pr_debug("%s: mxs_iomux_setup_multiple_pads() failed with rc: %d\n",
__func__, ret);
return ret;
}
pr_debug("%s: Registering FEC1 device\n", __func__);
mx28_add_fec(1, &tx28_fec1_data);
return 0;
}
arch/arm/mach-mxs/module-tx28.h deleted 100644 → 0
View file @ 44ffb78f
/*
* Copyright (C) 2010 Pengutronix
* Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
*
* This program is free software; you can redistribute it and/or modify it under
* the terms of the GNU General Public License version 2 as published by the
* Free Software Foundation.
*/
int __init tx28_add_fec0(void);
int __init tx28_add_fec1(void);
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7