Commit ac4c1a9b authored by Sascha Hauer's avatar Sascha Hauer Committed by Greg Kroah-Hartman

staging: drm/imx: Add LDB support

This adds support for the LVDS Display Bridge contained
in i.MX5 and i.MX6 SoCs.

Bit mapping, data width, and video timings are configurable
via device tree. Dual-channel mode is supported for a single
high-resolution source.
Signed-off-by: default avatarSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: default avatarPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: default avatarShawn Guo <shawn.guo@linaro.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 0c293592
Device-Tree bindings for LVDS Display Bridge (ldb)
LVDS Display Bridge
===================
The LVDS Display Bridge device tree node contains up to two lvds-channel
nodes describing each of the two LVDS encoder channels of the bridge.
Required properties:
- #address-cells : should be <1>
- #size-cells : should be <0>
- compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
Both LDB versions are similar, but i.MX6 has an additional
multiplexer in the front to select any of the four IPU display
interfaces as input for each LVDS channel.
- gpr : should be <&gpr> on i.MX53 and i.MX6q.
The phandle points to the iomuxc-gpr region containing the LVDS
control register.
- clocks, clock-names : phandles to the LDB divider and selector clocks and to
the display interface selector clocks, as described in
Documentation/devicetree/bindings/clock/clock-bindings.txt
The following clocks are expected on i.MX53:
"di0_pll" - LDB LVDS channel 0 mux
"di1_pll" - LDB LVDS channel 1 mux
"di0" - LDB LVDS channel 0 gate
"di1" - LDB LVDS channel 1 gate
"di0_sel" - IPU1 DI0 mux
"di1_sel" - IPU1 DI1 mux
On i.MX6q the following additional clocks are needed:
"di2_sel" - IPU2 DI0 mux
"di3_sel" - IPU2 DI1 mux
The needed clock numbers for each are documented in
Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
Documentation/devicetree/bindings/clock/imx6q-clock.txt.
Optional properties:
- pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
- pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
not used on i.MX6q
- fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
be configured - one input will be distributed on both outputs in dual
channel mode
LVDS Channel
============
Each LVDS Channel has to contain a display-timings node that describes the
video timings for the connected LVDS display. For detailed information, also
have a look at Documentation/devicetree/bindings/video/display-timing.txt.
Required properties:
- reg : should be <0> or <1>
- crtcs : a list of phandles with index pointing to the IPU display interfaces
that can be used as video source for this channel.
- fsl,data-mapping : should be "spwg" or "jeida"
This describes how the color bits are laid out in the
serialized LVDS signal.
- fsl,data-width : should be <18> or <24>
example:
gpr: iomuxc-gpr@53fa8000 {
/* ... */
};
ldb: ldb@53fa8008 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx53-ldb";
gpr = <&gpr>;
clocks = <&clks 122>, <&clks 120>,
<&clks 115>, <&clks 116>,
<&clks 123>, <&clks 85>;
clock-names = "di0_pll", "di1_pll",
"di0_sel", "di1_sel",
"di0", "di1";
lvds-channel@0 {
reg = <0>;
crtcs = <&ipu 0>;
fsl,data-mapping = "spwg";
fsl,data-width = <24>;
display-timings {
/* ... */
};
};
lvds-channel@1 {
reg = <1>;
crtcs = <&ipu 1>;
fsl,data-mapping = "spwg";
fsl,data-width = <24>;
display-timings {
/* ... */
};
};
};
......@@ -30,6 +30,14 @@ config DRM_IMX_TVE
Choose this to enable the internal Television Encoder (TVe)
found on i.MX53 processors.
config DRM_IMX_LDB
tristate "Support for LVDS displays"
depends on DRM_IMX
select OF_VIDEOMODE
help
Choose this to enable the internal LVDS Display Bridge (LDB)
found on i.MX53 and i.MX6 processors.
config DRM_IMX_IPUV3_CORE
tristate "IPUv3 core support"
depends on DRM_IMX
......
......@@ -5,6 +5,7 @@ obj-$(CONFIG_DRM_IMX) += imxdrm.o
obj-$(CONFIG_DRM_IMX_PARALLEL_DISPLAY) += parallel-display.o
obj-$(CONFIG_DRM_IMX_TVE) += imx-tve.o
obj-$(CONFIG_DRM_IMX_LDB) += imx-ldb.o
obj-$(CONFIG_DRM_IMX_FB_HELPER) += imx-fbdev.o
obj-$(CONFIG_DRM_IMX_IPUV3_CORE) += ipu-v3/
obj-$(CONFIG_DRM_IMX_IPUV3) += ipuv3-crtc.o
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment