Commit adc4cefa authored by Appana Durga Kedareswara rao's avatar Appana Durga Kedareswara rao Committed by Michal Simek

microblaze: Add support for error injection

To inject the error using the tmr inject IP reset vectors need to be placed
in lmb(bram) due to the limitation in HW when this code runs out of DDR.
Below code adds the error inject code to the .init.ivt section to copy
it in machine_early_init to lmb/Bram location. C_BASE_VECTORS which allow
moving reset vectors out of 0 location is not currently supported by
Microblaze architecture, that's why all the time reset vectors with
injection code is all the time copied to address 0.

As of now getting this functionality working CPU switches to real mode
and simply jumps to bram, which causes triggering of fault which continues
to call_xmb_manager_break break handler which will at the end calls the
error count callback function and performs recovery.
Signed-off-by: default avatarAppana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Link: https://lore.kernel.org/r/20220627064024.771037-4-appana.durga.rao@xilinx.comSigned-off-by: default avatarMichal Simek <michal.simek@amd.com>
parent 88707ebe
......@@ -5,6 +5,8 @@
#ifndef _XILINX_MB_MANAGER_H
#define _XILINX_MB_MANAGER_H
# ifndef __ASSEMBLY__
#include <linux/of_address.h>
/*
......@@ -17,5 +19,11 @@
void xmb_manager_register(uintptr_t phys_baseaddr, u32 cr_val,
void (*callback)(void *data),
void *priv, void (*reset_callback)(void *data));
asmlinkage void xmb_inject_err(void);
# endif /* __ASSEMBLY__ */
/* Error injection offset */
#define XMB_INJECT_ERR_OFFSET 0x200
#endif /* _XILINX_MB_MANAGER_H */
......@@ -27,6 +27,7 @@
#include <asm/page.h>
#include <asm/unistd.h>
#include <asm/xilinx_mb_manager.h>
#include <linux/errno.h>
#include <asm/signal.h>
......@@ -1151,6 +1152,41 @@ ENTRY(_switch_to)
nop
#ifdef CONFIG_MB_MANAGER
.global xmb_inject_err
.section .text
.align 2
.ent xmb_inject_err
.type xmb_inject_err, @function
xmb_inject_err:
addik r1, r1, -PT_SIZE
SAVE_REGS
/* Switch to real mode */
VM_OFF;
set_bip;
mbar 1
mbar 2
bralid r15, XMB_INJECT_ERR_OFFSET
nop;
/* enable virtual mode */
set_vms;
/* barrier for instructions and data accesses */
mbar 1
mbar 2
/*
* Enable Interrupts, Virtual Protected Mode, equalize
* initial state for all possible entries.
*/
rtbd r0, 1f
nop;
1:
RESTORE_REGS
addik r1, r1, PT_SIZE
rtsd r15, 8;
nop;
.end xmb_inject_err
.section .data
.global xmb_manager_dev
.global xmb_manager_baseaddr
......@@ -1225,6 +1261,22 @@ ENTRY(_reset)
.org 0x20
brai TOPHYS(_hw_exception_handler); /* HW exception handler */
#ifdef CONFIG_MB_MANAGER
/*
* For TMR Inject API which injects the error should
* be executed from LMB.
* TMR Inject is programmed with address of 0x200 so that
* when program counter matches with this address error will
* be injected. 0x200 is expected to be next available bram
* offset, hence used for this api.
*/
.org XMB_INJECT_ERR_OFFSET
xmb_inject_error:
nop
rtsd r15, 8
nop
#endif
.section .rodata,"a"
#include "syscall_table.S"
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment