arm64: dts: ti: k3-am642-evm: add overlay for ICSSG1 2nd port

The am642-evm doesn't allow to enable 2 x CPSW3g ports and 2 x ICSSG1 ports
all together, so base k3-am642-evm.dts enables by default 2 x CPSW3g ports
and 1 x ICSSG1 ports, but it is also possible to support 1 x CPSW3g ports
and 2 x ICSSG1 ports configuration.

This patch adds overlay to support 1 x CPSW3g ports and 2 x ICSSG1 ports
configuration:
- Add label name 'mdio_mux_1' for 'mdio-mux-1' node so that the node
  'mdio-mux-1' can be disabled in the overlay using the label name.
- disable 2nd CPSW3g port
- update CPSW3g pinmuxes to not use RGMII2
- disable mdio-mux-1 and define mdio-mux-2 to route ICSSG1 MDIO to the
  shared DP83869 PHY
- add and enable ICSSG1 RGMII2 pinmuxes
- enable ICSSG1 MII1 port
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240215103036.2825096-4-danishanwar@ti.comSigned-off-by: Vignesh Raghavendra <vigneshr@ti.com>

arch/arm64/boot/dts/ti/Makefile

@@ -39,6 +39,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-hdmi-audio.dtbo
 
 # Boards with AM64x SoC
 dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am642-evm-icssg1-dualemac.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-tqma64xxl-mbax4xxl.dtb
@@ -115,6 +116,8 @@ k3-am62a7-sk-csi2-ov5640-dtbs := k3-am62a7-sk.dtb \
 k3-am62a7-sk-csi2-tevi-ov5640-dtbs := k3-am62a7-sk.dtb \
 	k3-am62x-sk-csi2-tevi-ov5640.dtbo
 k3-am62a7-sk-hdmi-audio-dtbs := k3-am62a7-sk.dtb k3-am62x-sk-hdmi-audio.dtbo
+k3-am642-evm-icssg1-dualemac-dtbs := \
+	k3-am642-evm.dtb k3-am642-evm-icssg1-dualemac.dtbo
 k3-am642-tqma64xxl-mbax4xxl-sdcard-dtbs := \
 	k3-am642-tqma64xxl-mbax4xxl.dtb k3-am64-tqma64xxl-mbax4xxl-sdcard.dtbo
 k3-am642-tqma64xxl-mbax4xxl-wlan-dtbs := \
@@ -139,6 +142,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
 	k3-am62a7-sk-csi2-imx219.dtb \
 	k3-am62a7-sk-csi2-ov5640.dtb \
 	k3-am62a7-sk-hdmi-audio.dtb \
+	k3-am642-evm-icssg1-dualemac.dtb \
 	k3-am642-tqma64xxl-mbax4xxl-sdcard.dtb \
 	k3-am642-tqma64xxl-mbax4xxl-wlan.dtb \
 	k3-am68-sk-base-board-csi2-dual-imx219-dtbs \
@@ -152,6 +156,7 @@ DTC_FLAGS_k3-am625-beagleplay += -@
 DTC_FLAGS_k3-am625-sk += -@
 DTC_FLAGS_k3-am62-lp-sk += -@
 DTC_FLAGS_k3-am62a7-sk += -@
+DTC_FLAGS_k3-am642-evm += -@
 DTC_FLAGS_k3-am642-tqma64xxl-mbax4xxl += -@
 DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
 DTC_FLAGS_k3-am68-sk-base-board += -@

arch/arm64/boot/dts/ti/k3-am642-evm-icssg1-dualemac.dtso

+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/**
+ * DT overlay for enabling 2nd ICSSG1 port on AM642 EVM
+ *
+ * Copyright (C) 2020-2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-pinctrl.h"
+
+&{/} {
+	aliases {
+		ethernet1 = "/icssg1-eth/ethernet-ports/port@1";
+	};
+
+	mdio-mux-2 {
+		compatible = "mdio-mux-multiplexer";
+		mux-controls = <&mdio_mux>;
+		mdio-parent-bus = <&icssg1_mdio>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio@0 {
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			icssg1_phy2: ethernet-phy@3 {
+				reg = <3>;
+				tx-internal-delay-ps = <250>;
+				rx-internal-delay-ps = <2000>;
+			};
+		};
+	};
+};
+
+&main_pmx0 {
+	icssg1_rgmii2_pins_default: icssg1-rgmii2-default-pins {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0108, PIN_INPUT, 2) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */
+			AM64X_IOPAD(0x010c, PIN_INPUT, 2) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */
+			AM64X_IOPAD(0x0110, PIN_INPUT, 2) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */
+			AM64X_IOPAD(0x0114, PIN_INPUT, 2) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */
+			AM64X_IOPAD(0x0120, PIN_INPUT, 2) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */
+			AM64X_IOPAD(0x0118, PIN_INPUT, 2) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */
+			AM64X_IOPAD(0x0134, PIN_OUTPUT, 2) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */
+			AM64X_IOPAD(0x0138, PIN_OUTPUT, 2) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */
+			AM64X_IOPAD(0x013c, PIN_OUTPUT, 2) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */
+			AM64X_IOPAD(0x0140, PIN_OUTPUT, 2) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */
+			AM64X_IOPAD(0x0148, PIN_OUTPUT, 2) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */
+			AM64X_IOPAD(0x0144, PIN_OUTPUT, 2) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */
+		>;
+	};
+};
+
+&cpsw3g {
+	pinctrl-0 = <&rgmii1_pins_default>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&mdio_mux_1 {
+	status = "disabled";
+};
+
+&icssg1_eth {
+	pinctrl-0 = <&icssg1_rgmii1_pins_default>, <&icssg1_rgmii2_pins_default>;
+};
+
+&icssg1_emac1 {
+	status = "okay";
+	phy-handle = <&icssg1_phy2>;
+	phy-mode = "rgmii-id";
+};

arch/arm64/boot/dts/ti/k3-am642-evm.dts

@@ -199,7 +199,7 @@ mdio_mux: mux-controller {
 		mux-gpios = <&exp1 12 GPIO_ACTIVE_HIGH>;
 	};
 
-	mdio-mux-1 {
+	mdio_mux_1: mdio-mux-1 {
 		compatible = "mdio-mux-multiplexer";
 		mux-controls = <&mdio_mux>;
 		mdio-parent-bus = <&cpsw3g_mdio>;