Merge branch 'linus' into perfcounters/rename

Merge reason: pull in all the latest code before doing the rename.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Documentation/arm/OMAP/omap_pm

+
+The OMAP PM interface
+=====================
+
+This document describes the temporary OMAP PM interface.  Driver
+authors use these functions to communicate minimum latency or
+throughput constraints to the kernel power management code.
+Over time, the intention is to merge features from the OMAP PM
+interface into the Linux PM QoS code.
+
+Drivers need to express PM parameters which:
+
+- support the range of power management parameters present in the TI SRF;
+
+- separate the drivers from the underlying PM parameter
+  implementation, whether it is the TI SRF or Linux PM QoS or Linux
+  latency framework or something else;
+
+- specify PM parameters in terms of fundamental units, such as
+  latency and throughput, rather than units which are specific to OMAP
+  or to particular OMAP variants;
+
+- allow drivers which are shared with other architectures (e.g.,
+  DaVinci) to add these constraints in a way which won't affect non-OMAP
+  systems,
+
+- can be implemented immediately with minimal disruption of other
+  architectures.
+
+
+This document proposes the OMAP PM interface, including the following
+five power management functions for driver code:
+
+1. Set the maximum MPU wakeup latency:
+   (*pdata->set_max_mpu_wakeup_lat)(struct device *dev, unsigned long t)
+
+2. Set the maximum device wakeup latency:
+   (*pdata->set_max_dev_wakeup_lat)(struct device *dev, unsigned long t)
+
+3. Set the maximum system DMA transfer start latency (CORE pwrdm):
+   (*pdata->set_max_sdma_lat)(struct device *dev, long t)
+
+4. Set the minimum bus throughput needed by a device:
+   (*pdata->set_min_bus_tput)(struct device *dev, u8 agent_id, unsigned long r)
+
+5. Return the number of times the device has lost context
+   (*pdata->get_dev_context_loss_count)(struct device *dev)
+
+
+Further documentation for all OMAP PM interface functions can be
+found in arch/arm/plat-omap/include/mach/omap-pm.h.
+
+
+The OMAP PM layer is intended to be temporary
+---------------------------------------------
+
+The intention is that eventually the Linux PM QoS layer should support
+the range of power management features present in OMAP3.  As this
+happens, existing drivers using the OMAP PM interface can be modified
+to use the Linux PM QoS code; and the OMAP PM interface can disappear.
+
+
+Driver usage of the OMAP PM functions
+-------------------------------------
+
+As the 'pdata' in the above examples indicates, these functions are
+exposed to drivers through function pointers in driver .platform_data
+structures.  The function pointers are initialized by the board-*.c
+files to point to the corresponding OMAP PM functions:
+.set_max_dev_wakeup_lat will point to
+omap_pm_set_max_dev_wakeup_lat(), etc.  Other architectures which do
+not support these functions should leave these function pointers set
+to NULL.  Drivers should use the following idiom:
+
+        if (pdata->set_max_dev_wakeup_lat)
+            (*pdata->set_max_dev_wakeup_lat)(dev, t);
+
+The most common usage of these functions will probably be to specify
+the maximum time from when an interrupt occurs, to when the device
+becomes accessible.  To accomplish this, driver writers should use the
+set_max_mpu_wakeup_lat() function to to constrain the MPU wakeup
+latency, and the set_max_dev_wakeup_lat() function to constrain the
+device wakeup latency (from clk_enable() to accessibility).  For
+example,
+
+        /* Limit MPU wakeup latency */
+        if (pdata->set_max_mpu_wakeup_lat)
+            (*pdata->set_max_mpu_wakeup_lat)(dev, tc);
+
+        /* Limit device powerdomain wakeup latency */
+        if (pdata->set_max_dev_wakeup_lat)
+            (*pdata->set_max_dev_wakeup_lat)(dev, td);
+
+        /* total wakeup latency in this example: (tc + td) */
+
+The PM parameters can be overwritten by calling the function again
+with the new value.  The settings can be removed by calling the
+function with a t argument of -1 (except in the case of
+set_max_bus_tput(), which should be called with an r argument of 0).
+
+The fifth function above, omap_pm_get_dev_context_loss_count(),
+is intended as an optimization to allow drivers to determine whether the
+device has lost its internal context.  If context has been lost, the
+driver must restore its internal context before proceeding.
+
+
+Other specialized interface functions
+-------------------------------------
+
+The five functions listed above are intended to be usable by any
+device driver.  DSPBridge and CPUFreq have a few special requirements.
+DSPBridge expresses target DSP performance levels in terms of OPP IDs.
+CPUFreq expresses target MPU performance levels in terms of MPU
+frequency.  The OMAP PM interface contains functions for these
+specialized cases to convert that input information (OPPs/MPU
+frequency) into the form that the underlying power management
+implementation needs:
+
+6. (*pdata->dsp_get_opp_table)(void)
+
+7. (*pdata->dsp_set_min_opp)(u8 opp_id)
+
+8. (*pdata->dsp_get_opp)(void)
+
+9. (*pdata->cpu_get_freq_table)(void)
+
+10. (*pdata->cpu_set_freq)(unsigned long f)
+
+11. (*pdata->cpu_get_freq)(void)

Documentation/cpu-freq/user-guide.txt

@@ -176,7 +176,9 @@ scaling_governor,		and by "echoing" the name of another
 				work on some specific architectures or
 				processors.
 
-cpuinfo_cur_freq :		Current speed of the CPU, in KHz.
+cpuinfo_cur_freq :		Current frequency of the CPU as obtained from
+				the hardware, in KHz. This is the frequency
+				the CPU actually runs at.
 
 scaling_available_frequencies : List of available frequencies, in KHz.
 
@@ -196,7 +198,10 @@ related_cpus :			List of CPUs that need some sort of frequency
 
 scaling_driver :		Hardware driver for cpufreq.
 
-scaling_cur_freq :		Current frequency of the CPU, in KHz.
+scaling_cur_freq :		Current frequency of the CPU as determined by
+				the governor and cpufreq core, in KHz. This is
+				the frequency the kernel thinks the CPU runs
+				at.
 
 If you have selected the "userspace" governor which allows you to
 set the CPU operating frequency to a specific value, you can read out

Documentation/filesystems/ext4.txt

@@ -134,15 +134,9 @@ ro                   	Mount filesystem read only. Note that ext4 will
                      	mount options "ro,noload" can be used to prevent
 		     	writes to the filesystem.
 
-journal_checksum	Enable checksumming of the journal transactions.
-			This will allow the recovery code in e2fsck and the
-			kernel to detect corruption in the kernel.  It is a
-			compatible change and will be ignored by older kernels.
-
 journal_async_commit	Commit block can be written to disk without waiting
 			for descriptor blocks. If enabled older kernels cannot
-			mount the device. This will enable 'journal_checksum'
-			internally.
+			mount the device.
 
 journal=update		Update the ext4 file system's journal to the current
 			format.
@@ -263,10 +257,18 @@ resuid=n		The user ID which may use the reserved blocks.
 
 sb=n			Use alternate superblock at this location.
 
-quota
-noquota
-grpquota
-usrquota
+quota			These options are ignored by the filesystem. They
+noquota			are used only by quota tools to recognize volumes
+grpquota		where quota should be turned on. See documentation
+usrquota		in the quota-tools package for more details
+			(http://sourceforge.net/projects/linuxquota).
+
+jqfmt=<quota type>	These options tell filesystem details about quota
+usrjquota=<file>	so that quota information can be properly updated
+grpjquota=<file>	during journal replay. They replace the above
+			quota options. See documentation in the quota-tools
+			package for more details
+			(http://sourceforge.net/projects/linuxquota).
 
 bh		(*)	ext4 associates buffer heads to data pages to
 nobh			(a) cache disk block mapping information

Documentation/hwmon/wm831x

+Kernel driver wm831x-hwmon
+==========================
+
+Supported chips:
+  * Wolfson Microelectronics WM831x PMICs
+    Prefix: 'wm831x'
+    Datasheet:
+	http://www.wolfsonmicro.com/products/WM8310
+	http://www.wolfsonmicro.com/products/WM8311
+	http://www.wolfsonmicro.com/products/WM8312
+
+Authors: Mark Brown <broonie@opensource.wolfsonmicro.com>
+
+Description
+-----------
+
+The WM831x series of PMICs include an AUXADC which can be used to
+monitor a range of system operating parameters, including the voltages
+of the major supplies within the system.  Currently the driver provides
+reporting of all the input values but does not provide any alarms.
+
+Voltage Monitoring
+------------------
+
+Voltages are sampled by a 12 bit ADC.  Voltages in milivolts are 1.465
+times the ADC value.
+
+Temperature Monitoring
+----------------------
+
+Temperatures are sampled by a 12 bit ADC.  Chip and battery temperatures
+are available.  The chip temperature is calculated as:
+
+	Degrees celsius = (512.18 - data) / 1.0983
+
+while the battery temperature calculation will depend on the NTC
+thermistor component.

Documentation/hwmon/wm8350

+Kernel driver wm8350-hwmon
+==========================
+
+Supported chips:
+  * Wolfson Microelectronics WM835x PMICs
+    Prefix: 'wm8350'
+    Datasheet:
+	http://www.wolfsonmicro.com/products/WM8350
+	http://www.wolfsonmicro.com/products/WM8351
+	http://www.wolfsonmicro.com/products/WM8352
+
+Authors: Mark Brown <broonie@opensource.wolfsonmicro.com>
+
+Description
+-----------
+
+The WM835x series of PMICs include an AUXADC which can be used to
+monitor a range of system operating parameters, including the voltages
+of the major supplies within the system.  Currently the driver provides
+simple access to these major supplies.
+
+Voltage Monitoring
+------------------
+
+Voltages are sampled by a 12 bit ADC.  For the internal supplies the ADC
+is referenced to the system VRTC.

Documentation/kernel-doc-nano-HOWTO.txt

@@ -66,7 +66,9 @@ Example kernel-doc function comment:
  * The longer description can have multiple paragraphs.
  */
 
-The first line, with the short description, must be on a single line.
+The short description following the subject can span multiple lines
+and ends with an @argument description, an empty line or the end of
+the comment block.
 
 The @argument descriptions must begin on the very next line following
 this opening short function description line, with no intervening

Documentation/kernel-parameters.txt

@@ -1565,7 +1565,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			of returning the full 64-bit number.
 			The default is to return 64-bit inode numbers.
 
-	nmi_debug=	[KNL,AVR32] Specify one or more actions to take
+	nmi_debug=	[KNL,AVR32,SH] Specify one or more actions to take
 			when a NMI is triggered.
 			Format: [state][,regs][,debounce][,die]
 

Documentation/kref.txt

@@ -84,7 +84,6 @@ int my_data_handler(void)
 	task = kthread_run(more_data_handling, data, "more_data_handling");
 	if (task == ERR_PTR(-ENOMEM)) {
 		rv = -ENOMEM;
-	        kref_put(&data->refcount, data_release);
 		goto out;
 	}
 

Documentation/x86/boot.txt

@@ -599,6 +599,7 @@ Protocol:	2.07+
   0x00000000	The default x86/PC environment
   0x00000001	lguest
   0x00000002	Xen
+  0x00000003	Moorestown MID
 
 Field name:	hardware_subarch_data
 Type:		write (subarch-dependent)

MAINTAINERS

@@ -1973,7 +1973,6 @@ F:	fs/ext2/
 F:	include/linux/ext2*
 
 EXT3 FILE SYSTEM
-M:	Stephen Tweedie <sct@redhat.com>
 M:	Andrew Morton <akpm@linux-foundation.org>
 M:	Andreas Dilger <adilger@sun.com>
 L:	linux-ext4@vger.kernel.org
@@ -2901,8 +2900,8 @@ F:	fs/jffs2/
 F:	include/linux/jffs2.h
 
 JOURNALLING LAYER FOR BLOCK DEVICES (JBD)
-M:	Stephen Tweedie <sct@redhat.com>
 M:	Andrew Morton <akpm@linux-foundation.org>
+M:	Jan Kara <jack@suse.cz>
 L:	linux-ext4@vger.kernel.org
 S:	Maintained
 F:	fs/jbd*/
@@ -4455,6 +4454,14 @@ S:	Maintained
 F:	kernel/sched*
 F:	include/linux/sched.h
 
+SCORE ARCHITECTURE
+P:	Chen Liqin
+M:	liqin.chen@sunplusct.com
+P:	Lennox Wu
+M:	lennox.wu@sunplusct.com
+W:	http://www.sunplusct.com
+S:	Supported
+
 SCSI CDROM DRIVER
 M:	Jens Axboe <axboe@kernel.dk>
 L:	linux-scsi@vger.kernel.org
@@ -4654,6 +4661,12 @@ F:	arch/arm/mach-s3c2410/
 F:	drivers/*/*s3c2410*
 F:	drivers/*/*/*s3c2410*
 
+TI DAVINCI MACHINE SUPPORT
+P:	Kevin Hilman
+M:	davinci-linux-open-source@linux.davincidsp.com
+S:	Supported
+F:	arch/arm/mach-davinci
+
 SIS 190 ETHERNET DRIVER
 M:	Francois Romieu <romieu@fr.zoreil.com>
 L:	netdev@vger.kernel.org
@@ -5678,6 +5691,26 @@ S:	Supported
 F:	drivers/input/touchscreen/*wm97*
 F:	include/linux/wm97xx.h
 
+WOLFSON MICROELECTRONICS PMIC DRIVERS
+P:	Mark Brown
+M:	broonie@opensource.wolfsonmicro.com
+L:	linux-kernel@vger.kernel.org
+T:	git git://opensource.wolfsonmicro.com/linux-2.6-audioplus
+W:	http://opensource.wolfsonmicro.com/node/8
+S:	Supported
+F:	drivers/leds/leds-wm83*.c
+F:	drivers/mfd/wm8*.c
+F:	drivers/power/wm83*.c
+F:	drivers/rtc/rtc-wm83*.c
+F:	drivers/regulator/wm8*.c
+F:	drivers/video/backlight/wm83*_bl.c
+F:	drivers/watchdog/wm83*_wdt.c
+F:	include/linux/mfd/wm831x/
+F:	include/linux/mfd/wm8350/
+F:	include/linux/mfd/wm8400/
+F:	sound/soc/codecs/wm8350.c
+F:	sound/soc/codecs/wm8400.c
+
 X.25 NETWORK LAYER
 M:	Henner Eisen <eis@baty.hanse.de>
 L:	linux-x25@vger.kernel.org

arch/arm/configs/omap3_beagle_defconfig

@@ -128,6 +128,7 @@ CONFIG_DEFAULT_AS=y
 # CONFIG_DEFAULT_NOOP is not set
 CONFIG_DEFAULT_IOSCHED="anticipatory"
 CONFIG_CLASSIC_RCU=y
+CONFIG_FREEZER=y
 
 #
 # System Type
@@ -236,6 +237,7 @@ CONFIG_ARM_THUMB=y
 # CONFIG_CPU_BPREDICT_DISABLE is not set
 CONFIG_HAS_TLS_REG=y
 # CONFIG_OUTER_CACHE is not set
+CONFIG_COMMON_CLKDEV=y
 
 #
 # Bus support
@@ -317,7 +319,12 @@ CONFIG_BINFMT_MISC=y
 #
 # Power management options
 #
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_APM_EMULATION is not set
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_NET=y
 
@@ -713,6 +720,7 @@ CONFIG_GPIOLIB=y
 # CONFIG_GPIO_MAX732X is not set
 # CONFIG_GPIO_PCA953X is not set
 # CONFIG_GPIO_PCF857X is not set
+CONFIG_GPIO_TWL4030=y
 
 #
 # PCI GPIO expanders:
@@ -741,6 +749,7 @@ CONFIG_SSB_POSSIBLE=y
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_EGPIO is not set
 # CONFIG_HTC_PASIC3 is not set
+CONFIG_TWL4030_CORE=y
 # CONFIG_UCB1400_CORE is not set
 # CONFIG_MFD_TMIO is not set
 # CONFIG_MFD_T7L66XB is not set
@@ -787,7 +796,7 @@ CONFIG_DUMMY_CONSOLE=y
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
-# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB_ARCH_HAS_EHCI=y
 CONFIG_USB=y
 # CONFIG_USB_DEBUG is not set
 # CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
@@ -798,7 +807,8 @@ CONFIG_USB=y
 CONFIG_USB_DEVICEFS=y
 CONFIG_USB_DEVICE_CLASS=y
 # CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_OTG is not set
+CONFIG_USB_SUSPEND=y
+CONFIG_USB_OTG=y
 # CONFIG_USB_OTG_WHITELIST is not set
 # CONFIG_USB_OTG_BLACKLIST_HUB is not set
 CONFIG_USB_MON=y
@@ -806,6 +816,8 @@ CONFIG_USB_MON=y
 #
 # USB Host Controller Drivers
 #
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
 # CONFIG_USB_C67X00_HCD is not set
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
@@ -818,10 +830,10 @@ CONFIG_USB_MUSB_SOC=y
 #
 # OMAP 343x high speed USB support
 #
-CONFIG_USB_MUSB_HOST=y
+# CONFIG_USB_MUSB_HOST is not set
 # CONFIG_USB_MUSB_PERIPHERAL is not set
-# CONFIG_USB_MUSB_OTG is not set
-# CONFIG_USB_GADGET_MUSB_HDRC is not set
+CONFIG_USB_MUSB_OTG=y
+CONFIG_USB_GADGET_MUSB_HDRC=y
 CONFIG_USB_MUSB_HDRC_HCD=y
 # CONFIG_MUSB_PIO_ONLY is not set
 CONFIG_USB_INVENTRA_DMA=y
@@ -887,8 +899,8 @@ CONFIG_USB_GADGET_SELECTED=y
 # CONFIG_USB_GADGET_FSL_USB2 is not set
 # CONFIG_USB_GADGET_NET2280 is not set
 # CONFIG_USB_GADGET_PXA25X is not set
-CONFIG_USB_GADGET_M66592=y
-CONFIG_USB_M66592=y
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_M66592 is not set
 # CONFIG_USB_GADGET_PXA27X is not set
 # CONFIG_USB_GADGET_GOKU is not set
 # CONFIG_USB_GADGET_LH7A40X is not set
@@ -906,6 +918,15 @@ CONFIG_USB_ETH_RNDIS=y
 # CONFIG_USB_MIDI_GADGET is not set
 # CONFIG_USB_G_PRINTER is not set
 # CONFIG_USB_CDC_COMPOSITE is not set
+
+#
+# OTG and related infrastructure
+#
+CONFIG_USB_OTG_UTILS=y
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_ISP1301_OMAP is not set
+CONFIG_TWL4030_USB=y
+# CONFIG_NOP_USB_XCEIV is not set
 CONFIG_MMC=y
 # CONFIG_MMC_DEBUG is not set
 # CONFIG_MMC_UNSAFE_RESUME is not set
@@ -923,6 +944,7 @@ CONFIG_MMC_BLOCK_BOUNCE=y
 #
 # CONFIG_MMC_SDHCI is not set
 # CONFIG_MMC_OMAP is not set
+CONFIG_MMC_OMAP_HS=y
 # CONFIG_MEMSTICK is not set
 # CONFIG_ACCESSIBILITY is not set
 # CONFIG_NEW_LEDS is not set
@@ -981,10 +1003,11 @@ CONFIG_RTC_INTF_DEV=y
 #
 # Voltage and Current regulators
 #
-# CONFIG_REGULATOR is not set
+CONFIG_REGULATOR=y
 # CONFIG_REGULATOR_FIXED_VOLTAGE is not set
 # CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
 # CONFIG_REGULATOR_BQ24022 is not set
+CONFIG_REGULATOR_TWL4030=y
 # CONFIG_UIO is not set
 
 #

arch/arm/configs/omap_3430sdp_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.29-rc8
-# Fri Mar 13 14:17:01 2009
+# Linux kernel version: 2.6.30-omap1
+# Tue Jun 23 10:36:45 2009
 #
 CONFIG_ARM=y
 CONFIG_SYS_SUPPORTS_APM_EMULATION=y
@@ -197,9 +197,9 @@ CONFIG_OMAP_MCBSP=y
 CONFIG_OMAP_32K_TIMER=y
 CONFIG_OMAP_32K_TIMER_HZ=128
 CONFIG_OMAP_DM_TIMER=y
-# CONFIG_OMAP_LL_DEBUG_UART1 is not set
+CONFIG_OMAP_LL_DEBUG_UART1=y
 # CONFIG_OMAP_LL_DEBUG_UART2 is not set
-CONFIG_OMAP_LL_DEBUG_UART3=y
+# CONFIG_OMAP_LL_DEBUG_UART3 is not set
 CONFIG_OMAP_SERIAL_WAKE=y
 CONFIG_ARCH_OMAP34XX=y
 CONFIG_ARCH_OMAP3430=y
@@ -207,10 +207,10 @@ CONFIG_ARCH_OMAP3430=y
 #
 # OMAP Board Type
 #
-CONFIG_MACH_OMAP3_BEAGLE=y
-CONFIG_MACH_OMAP_LDP=y
-CONFIG_MACH_OVERO=y
-CONFIG_MACH_OMAP3_PANDORA=y
+# CONFIG_MACH_OMAP3_BEAGLE is not set
+# CONFIG_MACH_OMAP_LDP is not set
+# CONFIG_MACH_OVERO is not set
+# CONFIG_MACH_OMAP3_PANDORA is not set
 CONFIG_MACH_OMAP_3430SDP=y
 
 #
@@ -950,7 +950,7 @@ CONFIG_SPI_OMAP24XX=y
 # CONFIG_SPI_TLE62X0 is not set
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_GPIOLIB=y
-CONFIG_DEBUG_GPIO=y
+# CONFIG_DEBUG_GPIO is not set
 CONFIG_GPIO_SYSFS=y
 
 #
@@ -1370,7 +1370,7 @@ CONFIG_SND_OMAP_SOC=y
 CONFIG_SND_OMAP_SOC_MCBSP=y
 # CONFIG_SND_OMAP_SOC_OVERO is not set
 CONFIG_SND_OMAP_SOC_SDP3430=y
-CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=y
+# CONFIG_SND_OMAP_SOC_OMAP3_PANDORA is not set
 CONFIG_SND_SOC_I2C_AND_SPI=y
 # CONFIG_SND_SOC_ALL_CODECS is not set
 CONFIG_SND_SOC_TWL4030=y

arch/arm/configs/rx51_defconfig

@@ -1006,6 +1006,7 @@ CONFIG_WATCHDOG=y
 #
 # CONFIG_SOFT_WATCHDOG is not set
 CONFIG_OMAP_WATCHDOG=m
+CONFIG_TWL4030_WATCHDOG=m
 
 #
 # USB-based Watchdog Cards

arch/arm/mach-davinci/Kconfig

@@ -6,6 +6,9 @@ config AINTC
 config CP_INTC
 	bool
 
+config ARCH_DAVINCI_DMx
+	bool
+
 menu "TI DaVinci Implementations"
 
 comment "DaVinci Core Type"
@@ -13,20 +16,41 @@ comment "DaVinci Core Type"
 config ARCH_DAVINCI_DM644x
 	bool "DaVinci 644x based system"
 	select AINTC
+	select ARCH_DAVINCI_DMx
 
 config ARCH_DAVINCI_DM355
         bool "DaVinci 355 based system"
 	select AINTC
+	select ARCH_DAVINCI_DMx
 
 config ARCH_DAVINCI_DM646x
         bool "DaVinci 646x based system"
 	select AINTC
+	select ARCH_DAVINCI_DMx
+
+config ARCH_DAVINCI_DA830
+        bool "DA830/OMAP-L137 based system"
+	select CP_INTC
+	select ARCH_DAVINCI_DA8XX
+
+config ARCH_DAVINCI_DA850
+	bool "DA850/OMAP-L138 based system"
+	select CP_INTC
+	select ARCH_DAVINCI_DA8XX
+
+config ARCH_DAVINCI_DA8XX
+	bool
+
+config ARCH_DAVINCI_DM365
+	bool "DaVinci 365 based system"
+	select AINTC
+	select ARCH_DAVINCI_DMx
 
 comment "DaVinci Board Type"
 
 config MACH_DAVINCI_EVM
 	bool "TI DM644x EVM"
-	default y
+	default ARCH_DAVINCI_DM644x
 	depends on ARCH_DAVINCI_DM644x
 	help
 	  Configure this option to specify the whether the board used
@@ -41,6 +65,7 @@ config MACH_SFFSDR
 
 config MACH_DAVINCI_DM355_EVM
 	bool "TI DM355 EVM"
+	default ARCH_DAVINCI_DM355
 	depends on ARCH_DAVINCI_DM355
 	help
 	  Configure this option to specify the whether the board used
@@ -55,11 +80,33 @@ config MACH_DM355_LEOPARD
 
 config MACH_DAVINCI_DM6467_EVM
 	bool "TI DM6467 EVM"
+	default ARCH_DAVINCI_DM646x
 	depends on ARCH_DAVINCI_DM646x
 	help
 	  Configure this option to specify the whether the board used
 	  for development is a DM6467 EVM
 
+config MACH_DAVINCI_DM365_EVM
+	bool "TI DM365 EVM"
+	default ARCH_DAVINCI_DM365
+	depends on ARCH_DAVINCI_DM365
+	help
+	  Configure this option to specify whether the board used
+	  for development is a DM365 EVM
+
+config MACH_DAVINCI_DA830_EVM
+	bool "TI DA830/OMAP-L137 Reference Platform"
+	default ARCH_DAVINCI_DA830
+	depends on ARCH_DAVINCI_DA830
+	help
+	  Say Y here to select the TI DA830/OMAP-L137 Evaluation Module.
+
+config MACH_DAVINCI_DA850_EVM
+	bool "TI DA850/OMAP-L138 Reference Platform"
+	default ARCH_DAVINCI_DA850
+	depends on ARCH_DAVINCI_DA850
+	help
+	  Say Y here to select the TI DA850/OMAP-L138 Evaluation Module.
 
 config DAVINCI_MUX
 	bool "DAVINCI multiplexing support"

arch/arm/mach-davinci/Makefile

@@ -5,14 +5,17 @@
 
 # Common objects
 obj-y 			:= time.o clock.o serial.o io.o psc.o \
-			   gpio.o devices.o dma.o usb.o common.o sram.o
+			   gpio.o dma.o usb.o common.o sram.o
 
 obj-$(CONFIG_DAVINCI_MUX)		+= mux.o
 
 # Chip specific
-obj-$(CONFIG_ARCH_DAVINCI_DM644x)       += dm644x.o
-obj-$(CONFIG_ARCH_DAVINCI_DM355)        += dm355.o
-obj-$(CONFIG_ARCH_DAVINCI_DM646x)       += dm646x.o
+obj-$(CONFIG_ARCH_DAVINCI_DM644x)       += dm644x.o devices.o
+obj-$(CONFIG_ARCH_DAVINCI_DM355)        += dm355.o devices.o
+obj-$(CONFIG_ARCH_DAVINCI_DM646x)       += dm646x.o devices.o
+obj-$(CONFIG_ARCH_DAVINCI_DM365)	+= dm365.o devices.o
+obj-$(CONFIG_ARCH_DAVINCI_DA830)        += da830.o devices-da8xx.o
+obj-$(CONFIG_ARCH_DAVINCI_DA850)        += da850.o devices-da8xx.o
 
 obj-$(CONFIG_AINTC)			+= irq.o
 obj-$(CONFIG_CP_INTC)			+= cp_intc.o
@@ -23,3 +26,6 @@ obj-$(CONFIG_MACH_SFFSDR)		+= board-sffsdr.o
 obj-$(CONFIG_MACH_DAVINCI_DM355_EVM)	+= board-dm355-evm.o
 obj-$(CONFIG_MACH_DM355_LEOPARD)	+= board-dm355-leopard.o
 obj-$(CONFIG_MACH_DAVINCI_DM6467_EVM)	+= board-dm646x-evm.o
+obj-$(CONFIG_MACH_DAVINCI_DM365_EVM)	+= board-dm365-evm.o
+obj-$(CONFIG_MACH_DAVINCI_DA830_EVM)	+= board-da830-evm.o
+obj-$(CONFIG_MACH_DAVINCI_DA850_EVM)	+= board-da850-evm.o

arch/arm/mach-davinci/Makefile.boot

+ifeq ($(CONFIG_ARCH_DAVINCI_DA8XX),y)
+ifeq ($(CONFIG_ARCH_DAVINCI_DMx),y)
+$(error Cannot enable DaVinci and DA8XX platforms concurrently)
+else
+   zreladdr-y	:= 0xc0008000
+params_phys-y	:= 0xc0000100
+initrd_phys-y	:= 0xc0800000
+endif
+else
    zreladdr-y	:= 0x80008000
 params_phys-y	:= 0x80000100
 initrd_phys-y	:= 0x80800000
+endif

arch/arm/mach-davinci/board-da830-evm.c

+/*
+ * TI DA830/OMAP L137 EVM board
+ *
+ * Author: Mark A. Greer <mgreer@mvista.com>
+ * Derived from: arch/arm/mach-davinci/board-dm644x-evm.c
+ *
+ * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <mach/common.h>
+#include <mach/irqs.h>
+#include <mach/cp_intc.h>
+#include <mach/da8xx.h>
+#include <mach/asp.h>
+
+#define DA830_EVM_PHY_MASK		0x0
+#define DA830_EVM_MDIO_FREQUENCY	2200000	/* PHY bus frequency */
+
+static struct at24_platform_data da830_evm_i2c_eeprom_info = {
+	.byte_len	= SZ_256K / 8,
+	.page_size	= 64,
+	.flags		= AT24_FLAG_ADDR16,
+	.setup		= davinci_get_mac_addr,
+	.context	= (void *)0x7f00,
+};
+
+static struct i2c_board_info __initdata da830_evm_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("24c256", 0x50),
+		.platform_data	= &da830_evm_i2c_eeprom_info,
+	},
+	{
+		I2C_BOARD_INFO("tlv320aic3x", 0x18),
+	}
+};
+
+static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = {
+	.bus_freq	= 100,	/* kHz */
+	.bus_delay	= 0,	/* usec */
+};
+
+static struct davinci_uart_config da830_evm_uart_config __initdata = {
+	.enabled_uarts = 0x7,
+};
+
+static u8 da830_iis_serializer_direction[] = {
+	RX_MODE,	INACTIVE_MODE,	INACTIVE_MODE,	INACTIVE_MODE,
+	INACTIVE_MODE,	TX_MODE,	INACTIVE_MODE,	INACTIVE_MODE,
+	INACTIVE_MODE,	INACTIVE_MODE,	INACTIVE_MODE,	INACTIVE_MODE,
+};
+
+static struct snd_platform_data da830_evm_snd_data = {
+	.tx_dma_offset  = 0x2000,
+	.rx_dma_offset  = 0x2000,
+	.op_mode        = DAVINCI_MCASP_IIS_MODE,
+	.num_serializer = ARRAY_SIZE(da830_iis_serializer_direction),
+	.tdm_slots      = 2,
+	.serial_dir     = da830_iis_serializer_direction,
+	.eventq_no      = EVENTQ_0,
+	.version	= MCASP_VERSION_2,
+	.txnumevt	= 1,
+	.rxnumevt	= 1,
+};
+
+static __init void da830_evm_init(void)
+{
+	struct davinci_soc_info *soc_info = &davinci_soc_info;
+	int ret;
+
+	ret = da8xx_register_edma();
+	if (ret)
+		pr_warning("da830_evm_init: edma registration failed: %d\n",
+				ret);
+
+	ret = da8xx_pinmux_setup(da830_i2c0_pins);
+	if (ret)
+		pr_warning("da830_evm_init: i2c0 mux setup failed: %d\n",
+				ret);
+
+	ret = da8xx_register_i2c(0, &da830_evm_i2c_0_pdata);
+	if (ret)
+		pr_warning("da830_evm_init: i2c0 registration failed: %d\n",
+				ret);
+
+	soc_info->emac_pdata->phy_mask = DA830_EVM_PHY_MASK;
+	soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY;
+	soc_info->emac_pdata->rmii_en = 1;
+
+	ret = da8xx_pinmux_setup(da830_cpgmac_pins);
+	if (ret)
+		pr_warning("da830_evm_init: cpgmac mux setup failed: %d\n",
+				ret);
+
+	ret = da8xx_register_emac();
+	if (ret)
+		pr_warning("da830_evm_init: emac registration failed: %d\n",
+				ret);
+
+	ret = da8xx_register_watchdog();
+	if (ret)
+		pr_warning("da830_evm_init: watchdog registration failed: %d\n",
+				ret);
+
+	davinci_serial_init(&da830_evm_uart_config);
+	i2c_register_board_info(1, da830_evm_i2c_devices,
+			ARRAY_SIZE(da830_evm_i2c_devices));
+
+	ret = da8xx_pinmux_setup(da830_mcasp1_pins);
+	if (ret)
+		pr_warning("da830_evm_init: mcasp1 mux setup failed: %d\n",
+				ret);
+
+	da8xx_init_mcasp(1, &da830_evm_snd_data);
+}
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static int __init da830_evm_console_init(void)
+{
+	return add_preferred_console("ttyS", 2, "115200");
+}
+console_initcall(da830_evm_console_init);
+#endif
+
+static __init void da830_evm_irq_init(void)
+{
+	struct davinci_soc_info *soc_info = &davinci_soc_info;
+
+	cp_intc_init((void __iomem *)DA8XX_CP_INTC_VIRT, DA830_N_CP_INTC_IRQ,
+			soc_info->intc_irq_prios);
+}
+
+static void __init da830_evm_map_io(void)
+{
+	da830_init();
+}
+
+MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP L137 EVM")
+	.phys_io	= IO_PHYS,
+	.io_pg_offst	= (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
+	.boot_params	= (DA8XX_DDR_BASE + 0x100),
+	.map_io		= da830_evm_map_io,
+	.init_irq	= da830_evm_irq_init,
+	.timer		= &davinci_timer,
+	.init_machine	= da830_evm_init,
+MACHINE_END

arch/arm/mach-davinci/clock.c

@@ -227,7 +227,10 @@ static void __init clk_pll_init(struct clk *clk)
 	if (ctrl & PLLCTL_PLLEN) {
 		bypass = 0;
 		mult = __raw_readl(pll->base + PLLM);
-		mult = (mult & PLLM_PLLM_MASK) + 1;
+		if (cpu_is_davinci_dm365())
+			mult = 2 * (mult & PLLM_PLLM_MASK);
+		else
+			mult = (mult & PLLM_PLLM_MASK) + 1;
 	} else
 		bypass = 1;
 

arch/arm/mach-davinci/include/mach/asp.h

@@ -5,21 +5,73 @@
 #define __ASM_ARCH_DAVINCI_ASP_H
 
 #include <mach/irqs.h>
+#include <mach/edma.h>
 
-/* Bases of register banks */
+/* Bases of dm644x and dm355 register banks */
 #define DAVINCI_ASP0_BASE	0x01E02000
 #define DAVINCI_ASP1_BASE	0x01E04000
 
-/* EDMA channels */
+/* Bases of dm646x register banks */
+#define	DAVINCI_DM646X_MCASP0_REG_BASE		0x01D01000
+#define DAVINCI_DM646X_MCASP1_REG_BASE		0x01D01800
+
+/* Bases of da850/da830 McASP0  register banks */
+#define DAVINCI_DA8XX_MCASP0_REG_BASE	0x01D00000
+
+/* Bases of da830 McASP1 register banks */
+#define DAVINCI_DA830_MCASP1_REG_BASE	0x01D04000
+
+/* EDMA channels of dm644x and dm355 */
 #define DAVINCI_DMA_ASP0_TX	2
 #define DAVINCI_DMA_ASP0_RX	3
 #define DAVINCI_DMA_ASP1_TX	8
 #define DAVINCI_DMA_ASP1_RX	9
 
+/* EDMA channels of dm646x */
+#define	DAVINCI_DM646X_DMA_MCASP0_AXEVT0	6
+#define	DAVINCI_DM646X_DMA_MCASP0_AREVT0	9
+#define	DAVINCI_DM646X_DMA_MCASP1_AXEVT1	12
+
+/* EDMA channels of da850/da830 McASP0 */
+#define	DAVINCI_DA8XX_DMA_MCASP0_AREVT	0
+#define	DAVINCI_DA8XX_DMA_MCASP0_AXEVT	1
+
+/* EDMA channels of da830 McASP1 */
+#define	DAVINCI_DA830_DMA_MCASP1_AREVT	2
+#define	DAVINCI_DA830_DMA_MCASP1_AXEVT	3
+
 /* Interrupts */
 #define DAVINCI_ASP0_RX_INT	IRQ_MBRINT
 #define DAVINCI_ASP0_TX_INT	IRQ_MBXINT
 #define DAVINCI_ASP1_RX_INT	IRQ_MBRINT
 #define DAVINCI_ASP1_TX_INT	IRQ_MBXINT
 
+struct snd_platform_data {
+	u32 tx_dma_offset;
+	u32 rx_dma_offset;
+	enum dma_event_q eventq_no;	/* event queue number */
+	unsigned int codec_fmt;
+
+	/* McASP specific fields */
+	int tdm_slots;
+	u8 op_mode;
+	u8 num_serializer;
+	u8 *serial_dir;
+	u8 version;
+	u8 txnumevt;
+	u8 rxnumevt;
+};
+
+enum {
+	MCASP_VERSION_1 = 0,	/* DM646x */
+	MCASP_VERSION_2,	/* DA8xx/OMAPL1x */
+};
+
+#define INACTIVE_MODE	0
+#define TX_MODE		1
+#define RX_MODE		2
+
+#define DAVINCI_MCASP_IIS_MODE	0
+#define DAVINCI_MCASP_DIT_MODE	1
+
 #endif /* __ASM_ARCH_DAVINCI_ASP_H */

arch/arm/mach-davinci/include/mach/common.h

@@ -60,10 +60,10 @@ struct davinci_soc_info {
 	u8				*intc_irq_prios;
 	unsigned long			intc_irq_num;
 	struct davinci_timer_info	*timer_info;
-	void __iomem			*wdt_base;
 	void __iomem			*gpio_base;
 	unsigned			gpio_num;
 	unsigned			gpio_irq;
+	unsigned			gpio_unbanked;
 	struct platform_device		*serial_dev;
 	struct emac_platform_data	*emac_pdata;
 	dma_addr_t			sram_dma;

arch/arm/mach-davinci/include/mach/debug-macro.S

@@ -24,7 +24,15 @@
 		tst	\rx, #1			@ MMU enabled?
 		moveq	\rx, #0x01000000	@ physical base address
 		movne	\rx, #0xfe000000	@ virtual base
+#if defined(CONFIG_ARCH_DAVINCI_DA8XX) && defined(CONFIG_ARCH_DAVINCI_DMx)
+#error Cannot enable DaVinci and DA8XX platforms concurrently
+#elif defined(CONFIG_MACH_DAVINCI_DA830_EVM) || \
+	defined(CONFIG_MACH_DAVINCI_DA850_EVM)
+		orr	\rx, \rx, #0x00d00000	@ physical base address
+		orr	\rx, \rx, #0x0000d000	@ of UART 2
+#else
 		orr	\rx, \rx, #0x00c20000   @ UART 0
+#endif
 		.endm
 
 		.macro	senduart,rd,rx