Merge branch 'remotes/lorenzo/pci/al'

  - Add driver for Amazon Annapurna Labs PCIe controller (Jonathan Chocron)

  - Disable MSI-X since Annapurna Labs advertises it, but it's broken
    (Jonathan Chocron)

  - Disable VPD since Annapurna Labs advertises it, but it's broken
    (Jonathan Chocron)

  - Add ACS quirk since Annapurna Labs doesn't support ACS but does provide
    some equivalent protections (Ali Saidi)

* remotes/lorenzo/pci/al:
  PCI: dwc: Add validation that PCIe core is set to correct mode
  PCI: dwc: al: Add Amazon Annapurna Labs PCIe controller driver
  dt-bindings: PCI: Add Amazon's Annapurna Labs PCIe host bridge binding
  PCI: Add quirk to disable MSI-X support for Amazon's Annapurna Labs Root Port
  PCI/VPD: Prevent VPD access for Amazon's Annapurna Labs Root Port
  PCI: Add ACS quirk for Amazon Annapurna Labs root ports
  PCI: Add Amazon's Annapurna Labs vendor ID

# Conflicts:
#	drivers/pci/quirks.c

Documentation/devicetree/bindings/pci/pcie-al.txt

+* Amazon Annapurna Labs PCIe host bridge
+
+Amazon's Annapurna Labs PCIe Host Controller is based on the Synopsys DesignWare
+PCI core. It inherits common properties defined in
+Documentation/devicetree/bindings/pci/designware-pcie.txt.
+
+Properties of the host controller node that differ from it are:
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Value should contain
+			- "amazon,al-alpine-v2-pcie" for alpine_v2
+			- "amazon,al-alpine-v3-pcie" for alpine_v3
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Register ranges as listed in the reg-names property
+
+- reg-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Must include the following entries
+			- "config"	PCIe ECAM space
+			- "controller"	AL proprietary registers
+			- "dbi"		Designware PCIe registers
+
+Example:
+
+	pcie-external0: pcie@fb600000 {
+		compatible = "amazon,al-alpine-v3-pcie";
+		reg = <0x0 0xfb600000 0x0 0x00100000
+		       0x0 0xfd800000 0x0 0x00010000
+		       0x0 0xfd810000 0x0 0x00001000>;
+		reg-names = "config", "controller", "dbi";
+		bus-range = <0 255>;
+		device_type = "pci";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-map-mask = <0x00 0 0 7>;
+		interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; /* INTa */
+		ranges = <0x02000000 0x0 0xc0010000 0x0 0xc0010000 0x0 0x07ff0000>;
+	};

MAINTAINERS

@@ -12448,10 +12448,11 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/pci.git/
 S:	Supported
 F:	drivers/pci/controller/
 
-PCIE DRIVER FOR ANNAPURNA LABS
+PCIE DRIVER FOR AMAZON ANNAPURNA LABS
 M:	Jonathan Chocron <jonnyc@amazon.com>
 L:	linux-pci@vger.kernel.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/pci/pcie-al.txt
 F:	drivers/pci/controller/dwc/pcie-al.c
 
 PCIE DRIVER FOR AMLOGIC MESON

drivers/pci/controller/dwc/Kconfig

@@ -230,4 +230,16 @@ config PCIE_UNIPHIER
 	  Say Y here if you want PCIe controller support on UniPhier SoCs.
 	  This driver supports LD20 and PXs3 SoCs.
 
+config PCIE_AL
+	bool "Amazon Annapurna Labs PCIe controller"
+	depends on OF && (ARM64 || COMPILE_TEST)
+	depends on PCI_MSI_IRQ_DOMAIN
+	select PCIE_DW_HOST
+	help
+	  Say Y here to enable support of the Amazon's Annapurna Labs PCIe
+	  controller IP on Amazon SoCs. The PCIe controller uses the DesignWare
+	  core plus Annapurna Labs proprietary hardware wrappers. This is
+	  required only for DT-based platforms. ACPI platforms with the
+	  Annapurna Labs PCIe controller don't need to enable this.
+
 endmenu

drivers/pci/controller/dwc/pcie-al.c

@@ -91,3 +91,368 @@ struct pci_ecam_ops al_pcie_ops = {
 };
 
 #endif /* defined(CONFIG_ACPI) && defined(CONFIG_PCI_QUIRKS) */
+
+#ifdef CONFIG_PCIE_AL
+
+#include <linux/of_pci.h>
+#include "pcie-designware.h"
+
+#define AL_PCIE_REV_ID_2	2
+#define AL_PCIE_REV_ID_3	3
+#define AL_PCIE_REV_ID_4	4
+
+#define AXI_BASE_OFFSET		0x0
+
+#define DEVICE_ID_OFFSET	0x16c
+
+#define DEVICE_REV_ID			0x0
+#define DEVICE_REV_ID_DEV_ID_MASK	GENMASK(31, 16)
+
+#define DEVICE_REV_ID_DEV_ID_X4		0
+#define DEVICE_REV_ID_DEV_ID_X8		2
+#define DEVICE_REV_ID_DEV_ID_X16	4
+
+#define OB_CTRL_REV1_2_OFFSET	0x0040
+#define OB_CTRL_REV3_5_OFFSET	0x0030
+
+#define CFG_TARGET_BUS			0x0
+#define CFG_TARGET_BUS_MASK_MASK	GENMASK(7, 0)
+#define CFG_TARGET_BUS_BUSNUM_MASK	GENMASK(15, 8)
+
+#define CFG_CONTROL			0x4
+#define CFG_CONTROL_SUBBUS_MASK		GENMASK(15, 8)
+#define CFG_CONTROL_SEC_BUS_MASK	GENMASK(23, 16)
+
+struct al_pcie_reg_offsets {
+	unsigned int ob_ctrl;
+};
+
+struct al_pcie_target_bus_cfg {
+	u8 reg_val;
+	u8 reg_mask;
+	u8 ecam_mask;
+};
+
+struct al_pcie {
+	struct dw_pcie *pci;
+	void __iomem *controller_base; /* base of PCIe unit (not DW core) */
+	struct device *dev;
+	resource_size_t ecam_size;
+	unsigned int controller_rev_id;
+	struct al_pcie_reg_offsets reg_offsets;
+	struct al_pcie_target_bus_cfg target_bus_cfg;
+};
+
+#define PCIE_ECAM_DEVFN(x)		(((x) & 0xff) << 12)
+
+#define to_al_pcie(x)		dev_get_drvdata((x)->dev)
+
+static inline u32 al_pcie_controller_readl(struct al_pcie *pcie, u32 offset)
+{
+	return readl_relaxed(pcie->controller_base + offset);
+}
+
+static inline void al_pcie_controller_writel(struct al_pcie *pcie, u32 offset,
+					     u32 val)
+{
+	writel_relaxed(val, pcie->controller_base + offset);
+}
+
+static int al_pcie_rev_id_get(struct al_pcie *pcie, unsigned int *rev_id)
+{
+	u32 dev_rev_id_val;
+	u32 dev_id_val;
+
+	dev_rev_id_val = al_pcie_controller_readl(pcie, AXI_BASE_OFFSET +
+						  DEVICE_ID_OFFSET +
+						  DEVICE_REV_ID);
+	dev_id_val = FIELD_GET(DEVICE_REV_ID_DEV_ID_MASK, dev_rev_id_val);
+
+	switch (dev_id_val) {
+	case DEVICE_REV_ID_DEV_ID_X4:
+		*rev_id = AL_PCIE_REV_ID_2;
+		break;
+	case DEVICE_REV_ID_DEV_ID_X8:
+		*rev_id = AL_PCIE_REV_ID_3;
+		break;
+	case DEVICE_REV_ID_DEV_ID_X16:
+		*rev_id = AL_PCIE_REV_ID_4;
+		break;
+	default:
+		dev_err(pcie->dev, "Unsupported dev_id_val (0x%x)\n",
+			dev_id_val);
+		return -EINVAL;
+	}
+
+	dev_dbg(pcie->dev, "dev_id_val: 0x%x\n", dev_id_val);
+
+	return 0;
+}
+
+static int al_pcie_reg_offsets_set(struct al_pcie *pcie)
+{
+	switch (pcie->controller_rev_id) {
+	case AL_PCIE_REV_ID_2:
+		pcie->reg_offsets.ob_ctrl = OB_CTRL_REV1_2_OFFSET;
+		break;
+	case AL_PCIE_REV_ID_3:
+	case AL_PCIE_REV_ID_4:
+		pcie->reg_offsets.ob_ctrl = OB_CTRL_REV3_5_OFFSET;
+		break;
+	default:
+		dev_err(pcie->dev, "Unsupported controller rev_id: 0x%x\n",
+			pcie->controller_rev_id);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static inline void al_pcie_target_bus_set(struct al_pcie *pcie,
+					  u8 target_bus,
+					  u8 mask_target_bus)
+{
+	u32 reg;
+
+	reg = FIELD_PREP(CFG_TARGET_BUS_MASK_MASK, mask_target_bus) |
+	      FIELD_PREP(CFG_TARGET_BUS_BUSNUM_MASK, target_bus);
+
+	al_pcie_controller_writel(pcie, AXI_BASE_OFFSET +
+				  pcie->reg_offsets.ob_ctrl + CFG_TARGET_BUS,
+				  reg);
+}
+
+static void __iomem *al_pcie_conf_addr_map(struct al_pcie *pcie,
+					   unsigned int busnr,
+					   unsigned int devfn)
+{
+	struct al_pcie_target_bus_cfg *target_bus_cfg = &pcie->target_bus_cfg;
+	unsigned int busnr_ecam = busnr & target_bus_cfg->ecam_mask;
+	unsigned int busnr_reg = busnr & target_bus_cfg->reg_mask;
+	struct pcie_port *pp = &pcie->pci->pp;
+	void __iomem *pci_base_addr;
+
+	pci_base_addr = (void __iomem *)((uintptr_t)pp->va_cfg0_base +
+					 (busnr_ecam << 20) +
+					 PCIE_ECAM_DEVFN(devfn));
+
+	if (busnr_reg != target_bus_cfg->reg_val) {
+		dev_dbg(pcie->pci->dev, "Changing target bus busnum val from 0x%x to 0x%x\n",
+			target_bus_cfg->reg_val, busnr_reg);
+		target_bus_cfg->reg_val = busnr_reg;
+		al_pcie_target_bus_set(pcie,
+				       target_bus_cfg->reg_val,
+				       target_bus_cfg->reg_mask);
+	}
+
+	return pci_base_addr;
+}
+
+static int al_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+				 unsigned int devfn, int where, int size,
+				 u32 *val)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct al_pcie *pcie = to_al_pcie(pci);
+	unsigned int busnr = bus->number;
+	void __iomem *pci_addr;
+	int rc;
+
+	pci_addr = al_pcie_conf_addr_map(pcie, busnr, devfn);
+
+	rc = dw_pcie_read(pci_addr + where, size, val);
+
+	dev_dbg(pci->dev, "%d-byte config read from %04x:%02x:%02x.%d offset 0x%x (pci_addr: 0x%px) - val:0x%x\n",
+		size, pci_domain_nr(bus), bus->number,
+		PCI_SLOT(devfn), PCI_FUNC(devfn), where,
+		(pci_addr + where), *val);
+
+	return rc;
+}
+
+static int al_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
+				 unsigned int devfn, int where, int size,
+				 u32 val)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct al_pcie *pcie = to_al_pcie(pci);
+	unsigned int busnr = bus->number;
+	void __iomem *pci_addr;
+	int rc;
+
+	pci_addr = al_pcie_conf_addr_map(pcie, busnr, devfn);
+
+	rc = dw_pcie_write(pci_addr + where, size, val);
+
+	dev_dbg(pci->dev, "%d-byte config write to %04x:%02x:%02x.%d offset 0x%x (pci_addr: 0x%px) - val:0x%x\n",
+		size, pci_domain_nr(bus), bus->number,
+		PCI_SLOT(devfn), PCI_FUNC(devfn), where,
+		(pci_addr + where), val);
+
+	return rc;
+}
+
+static void al_pcie_config_prepare(struct al_pcie *pcie)
+{
+	struct al_pcie_target_bus_cfg *target_bus_cfg;
+	struct pcie_port *pp = &pcie->pci->pp;
+	unsigned int ecam_bus_mask;
+	u32 cfg_control_offset;
+	u8 subordinate_bus;
+	u8 secondary_bus;
+	u32 cfg_control;
+	u32 reg;
+
+	target_bus_cfg = &pcie->target_bus_cfg;
+
+	ecam_bus_mask = (pcie->ecam_size >> 20) - 1;
+	if (ecam_bus_mask > 255) {
+		dev_warn(pcie->dev, "ECAM window size is larger than 256MB. Cutting off at 256\n");
+		ecam_bus_mask = 255;
+	}
+
+	/* This portion is taken from the transaction address */
+	target_bus_cfg->ecam_mask = ecam_bus_mask;
+	/* This portion is taken from the cfg_target_bus reg */
+	target_bus_cfg->reg_mask = ~target_bus_cfg->ecam_mask;
+	target_bus_cfg->reg_val = pp->busn->start & target_bus_cfg->reg_mask;
+
+	al_pcie_target_bus_set(pcie, target_bus_cfg->reg_val,
+			       target_bus_cfg->reg_mask);
+
+	secondary_bus = pp->busn->start + 1;
+	subordinate_bus = pp->busn->end;
+
+	/* Set the valid values of secondary and subordinate buses */
+	cfg_control_offset = AXI_BASE_OFFSET + pcie->reg_offsets.ob_ctrl +
+			     CFG_CONTROL;
+
+	cfg_control = al_pcie_controller_readl(pcie, cfg_control_offset);
+
+	reg = cfg_control &
+	      ~(CFG_CONTROL_SEC_BUS_MASK | CFG_CONTROL_SUBBUS_MASK);
+
+	reg |= FIELD_PREP(CFG_CONTROL_SUBBUS_MASK, subordinate_bus) |
+	       FIELD_PREP(CFG_CONTROL_SEC_BUS_MASK, secondary_bus);
+
+	al_pcie_controller_writel(pcie, cfg_control_offset, reg);
+}
+
+static int al_pcie_host_init(struct pcie_port *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct al_pcie *pcie = to_al_pcie(pci);
+	int rc;
+
+	rc = al_pcie_rev_id_get(pcie, &pcie->controller_rev_id);
+	if (rc)
+		return rc;
+
+	rc = al_pcie_reg_offsets_set(pcie);
+	if (rc)
+		return rc;
+
+	al_pcie_config_prepare(pcie);
+
+	return 0;
+}
+
+static const struct dw_pcie_host_ops al_pcie_host_ops = {
+	.rd_other_conf = al_pcie_rd_other_conf,
+	.wr_other_conf = al_pcie_wr_other_conf,
+	.host_init = al_pcie_host_init,
+};
+
+static int al_add_pcie_port(struct pcie_port *pp,
+			    struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	int ret;
+
+	pp->ops = &al_pcie_host_ops;
+
+	ret = dw_pcie_host_init(pp);
+	if (ret) {
+		dev_err(dev, "failed to initialize host\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+};
+
+static int al_pcie_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *controller_res;
+	struct resource *ecam_res;
+	struct resource *dbi_res;
+	struct al_pcie *al_pcie;
+	struct dw_pcie *pci;
+
+	al_pcie = devm_kzalloc(dev, sizeof(*al_pcie), GFP_KERNEL);
+	if (!al_pcie)
+		return -ENOMEM;
+
+	pci = devm_kzalloc(dev, sizeof(*pci), GFP_KERNEL);
+	if (!pci)
+		return -ENOMEM;
+
+	pci->dev = dev;
+	pci->ops = &dw_pcie_ops;
+
+	al_pcie->pci = pci;
+	al_pcie->dev = dev;
+
+	dbi_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dbi");
+	pci->dbi_base = devm_pci_remap_cfg_resource(dev, dbi_res);
+	if (IS_ERR(pci->dbi_base)) {
+		dev_err(dev, "couldn't remap dbi base %pR\n", dbi_res);
+		return PTR_ERR(pci->dbi_base);
+	}
+
+	ecam_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
+	if (!ecam_res) {
+		dev_err(dev, "couldn't find 'config' reg in DT\n");
+		return -ENOENT;
+	}
+	al_pcie->ecam_size = resource_size(ecam_res);
+
+	controller_res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						      "controller");
+	al_pcie->controller_base = devm_ioremap_resource(dev, controller_res);
+	if (IS_ERR(al_pcie->controller_base)) {
+		dev_err(dev, "couldn't remap controller base %pR\n",
+			controller_res);
+		return PTR_ERR(al_pcie->controller_base);
+	}
+
+	dev_dbg(dev, "From DT: dbi_base: %pR, controller_base: %pR\n",
+		dbi_res, controller_res);
+
+	platform_set_drvdata(pdev, al_pcie);
+
+	return al_add_pcie_port(&pci->pp, pdev);
+}
+
+static const struct of_device_id al_pcie_of_match[] = {
+	{ .compatible = "amazon,al-alpine-v2-pcie",
+	},
+	{ .compatible = "amazon,al-alpine-v3-pcie",
+	},
+	{},
+};
+
+static struct platform_driver al_pcie_driver = {
+	.driver = {
+		.name	= "al-pcie",
+		.of_match_table = al_pcie_of_match,
+		.suppress_bind_attrs = true,
+	},
+	.probe = al_pcie_probe,
+};
+builtin_platform_driver(al_pcie_driver);
+
+#endif /* CONFIG_PCIE_AL*/

drivers/pci/controller/dwc/pcie-designware-ep.c

@@ -531,6 +531,7 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 	int ret;
 	u32 reg;
 	void *addr;
+	u8 hdr_type;
 	unsigned int nbars;
 	unsigned int offset;
 	struct pci_epc *epc;
@@ -595,6 +596,13 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
 	if (ep->ops->ep_init)
 		ep->ops->ep_init(ep);
 
+	hdr_type = dw_pcie_readb_dbi(pci, PCI_HEADER_TYPE);
+	if (hdr_type != PCI_HEADER_TYPE_NORMAL) {
+		dev_err(pci->dev, "PCIe controller is not set to EP mode (hdr_type:0x%x)!\n",
+			hdr_type);
+		return -EIO;
+	}
+
 	ret = of_property_read_u8(np, "max-functions", &epc->max_functions);
 	if (ret < 0)
 		epc->max_functions = 1;

drivers/pci/controller/dwc/pcie-designware-host.c

@@ -323,6 +323,7 @@ int dw_pcie_host_init(struct pcie_port *pp)
 	struct pci_bus *child;
 	struct pci_host_bridge *bridge;
 	struct resource *cfg_res;
+	u32 hdr_type;
 	int ret;
 
 	raw_spin_lock_init(&pci->pp.lock);
@@ -464,6 +465,21 @@ int dw_pcie_host_init(struct pcie_port *pp)
 			goto err_free_msi;
 	}
 
+	ret = dw_pcie_rd_own_conf(pp, PCI_HEADER_TYPE, 1, &hdr_type);
+	if (ret != PCIBIOS_SUCCESSFUL) {
+		dev_err(pci->dev, "Failed reading PCI_HEADER_TYPE cfg space reg (ret: 0x%x)\n",
+			ret);
+		ret = pcibios_err_to_errno(ret);
+		goto err_free_msi;
+	}
+	if (hdr_type != PCI_HEADER_TYPE_BRIDGE) {
+		dev_err(pci->dev,
+			"PCIe controller is not set to bridge type (hdr_type: 0x%x)!\n",
+			hdr_type);
+		ret = -EIO;
+		goto err_free_msi;
+	}
+
 	pp->root_bus_nr = pp->busn->start;
 
 	bridge->dev.parent = dev;

drivers/pci/quirks.c

@@ -2924,6 +2924,24 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0x10a1,
 			quirk_msi_intx_disable_qca_bug);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, 0xe091,
 			quirk_msi_intx_disable_qca_bug);
+
+/*
+ * Amazon's Annapurna Labs 1c36:0031 Root Ports don't support MSI-X, so it
+ * should be disabled on platforms where the device (mistakenly) advertises it.
+ *
+ * Notice that this quirk also disables MSI (which may work, but hasn't been
+ * tested), since currently there is no standard way to disable only MSI-X.
+ *
+ * The 0031 device id is reused for other non Root Port device types,
+ * therefore the quirk is registered for the PCI_CLASS_BRIDGE_PCI class.
+ */
+static void quirk_al_msi_disable(struct pci_dev *dev)
+{
+	dev->no_msi = 1;
+	pci_warn(dev, "Disabling MSI/MSI-X\n");
+}
+DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_AMAZON_ANNAPURNA_LABS, 0x0031,
+			      PCI_CLASS_BRIDGE_PCI, 8, quirk_al_msi_disable);
 #endif /* CONFIG_PCI_MSI */
 
 /*
@@ -4365,6 +4383,24 @@ static int pci_quirk_qcom_rp_acs(struct pci_dev *dev, u16 acs_flags)
 	return ret;
 }
 
+static int pci_quirk_al_acs(struct pci_dev *dev, u16 acs_flags)
+{
+	if (pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT)
+		return -ENOTTY;
+
+	/*
+	 * Amazon's Annapurna Labs root ports don't include an ACS capability,
+	 * but do include ACS-like functionality. The hardware doesn't support
+	 * peer-to-peer transactions via the root port and each has a unique
+	 * segment number.
+	 *
+	 * Additionally, the root ports cannot send traffic to each other.
+	 */
+	acs_flags &= ~(PCI_ACS_SV | PCI_ACS_RR | PCI_ACS_CR | PCI_ACS_UF);
+
+	return acs_flags ? 0 : 1;
+}
+
 /*
  * Sunrise Point PCH root ports implement ACS, but unfortunately as shown in
  * the datasheet (Intel 100 Series Chipset Family PCH Datasheet, Vol. 2,
@@ -4572,6 +4608,8 @@ static const struct pci_dev_acs_enabled {
 	{ PCI_VENDOR_ID_AMPERE, 0xE00B, pci_quirk_xgene_acs },
 	{ PCI_VENDOR_ID_AMPERE, 0xE00C, pci_quirk_xgene_acs },
 	{ PCI_VENDOR_ID_BROADCOM, 0xD714, pci_quirk_brcm_acs },
+	/* Amazon Annapurna Labs */
+	{ PCI_VENDOR_ID_AMAZON_ANNAPURNA_LABS, 0x0031, pci_quirk_al_acs },
 	{ 0 }
 };
 

drivers/pci/vpd.c

@@ -571,6 +571,12 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_LSI_LOGIC, 0x005f, quirk_blacklist_vpd);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATTANSIC, PCI_ANY_ID,
 		quirk_blacklist_vpd);
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_QLOGIC, 0x2261, quirk_blacklist_vpd);
+/*
+ * The Amazon Annapurna Labs 0x0031 device id is reused for other non Root Port
+ * device types, so the quirk is registered for the PCI_CLASS_BRIDGE_PCI class.
+ */
+DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_VENDOR_ID_AMAZON_ANNAPURNA_LABS, 0x0031,
+			      PCI_CLASS_BRIDGE_PCI, 8, quirk_blacklist_vpd);
 
 /*
  * For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the

include/linux/pci_ids.h

@@ -2570,6 +2570,8 @@
 
 #define PCI_VENDOR_ID_ASMEDIA		0x1b21
 
+#define PCI_VENDOR_ID_AMAZON_ANNAPURNA_LABS	0x1c36
+
 #define PCI_VENDOR_ID_CIRCUITCO		0x1cc8
 #define PCI_SUBSYSTEM_ID_CIRCUITCO_MINNOWBOARD	0x0001