[media] media: au0828 video change to use v4l_enable_media_source()

Change au0828 to check if tuner is free or not before changing tuner
configuration.

vidioc_g_tuner(), and au0828_v4l2_close() now call v4l-core interface
v4l_enable_media_source() before changing tuner configuration.

Remove au0828_enable_analog_tuner() as it is no longer needed because
v4l2-core implements common interfaces to check for media source
availability.

In addition, queue_setup() no longer needs the tuner availability check
since v4l2-core does it.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

drivers/media/usb/au0828/au0828-video.c

@@ -796,64 +796,6 @@ int au0828_v4l2_device_register(struct usb_interface *interface,
 	return 0;
 }
 
-static int au0828_enable_analog_tuner(struct au0828_dev *dev)
-{
-#ifdef CONFIG_MEDIA_CONTROLLER
-	struct media_device *mdev = dev->media_dev;
-	struct media_entity *source;
-	struct media_link *link, *found_link = NULL;
-	int ret, active_links = 0;
-
-	if (!mdev || !dev->decoder)
-		return 0;
-
-	/*
-	 * This will find the tuner that is connected into the decoder.
-	 * Technically, this is not 100% correct, as the device may be
-	 * using an analog input instead of the tuner. However, as we can't
-	 * do DVB streaming while the DMA engine is being used for V4L2,
-	 * this should be enough for the actual needs.
-	 */
-	list_for_each_entry(link, &dev->decoder->links, list) {
-		if (link->sink->entity == dev->decoder) {
-			found_link = link;
-			if (link->flags & MEDIA_LNK_FL_ENABLED)
-				active_links++;
-			break;
-		}
-	}
-
-	if (active_links == 1 || !found_link)
-		return 0;
-
-	source = found_link->source->entity;
-	list_for_each_entry(link, &source->links, list) {
-		struct media_entity *sink;
-		int flags = 0;
-
-		sink = link->sink->entity;
-
-		if (sink == dev->decoder)
-			flags = MEDIA_LNK_FL_ENABLED;
-
-		ret = media_entity_setup_link(link, flags);
-		if (ret) {
-			pr_err(
-				"Couldn't change link %s->%s to %s. Error %d\n",
-				source->name, sink->name,
-				flags ? "enabled" : "disabled",
-				ret);
-			return ret;
-		} else
-			au0828_isocdbg(
-				"link %s->%s was %s\n",
-				source->name, sink->name,
-				flags ? "ENABLED" : "disabled");
-	}
-#endif
-	return 0;
-}
-
 static int queue_setup(struct vb2_queue *vq,
 		       unsigned int *nbuffers, unsigned int *nplanes,
 		       unsigned int sizes[], void *alloc_ctxs[])
@@ -865,9 +807,6 @@ static int queue_setup(struct vb2_queue *vq,
 		return sizes[0] < size ? -EINVAL : 0;
 	*nplanes = 1;
 	sizes[0] = size;
-
-	au0828_enable_analog_tuner(dev);
-
 	return 0;
 }
 
@@ -1235,8 +1174,39 @@ static int au0828_v4l2_close(struct file *filp)
 		goto end;
 
 	if (dev->users == 1) {
-		/* Save some power by putting tuner to sleep */
-		v4l2_device_call_all(&dev->v4l2_dev, 0, core, s_power, 0);
+		/*
+		 * Avoid putting tuner in sleep if DVB or ALSA are
+		 * streaming.
+		 *
+		 * On most USB devices  like au0828 the tuner can
+		 * be safely put in sleep stare here if ALSA isn't
+		 * streaming. Exceptions are some very old USB tuner
+		 * models such as em28xx-based WinTV USB2 which have
+		 * a separate audio output jack. The devices that have
+		 * a separate audio output jack have analog tuners,
+		 * like Philips FM1236. Those devices are always on,
+		 * so the s_power callback are silently ignored.
+		 * So, the current logic here does the following:
+		 * Disable (put tuner to sleep) when
+		 * - ALSA and DVB aren't not streaming;
+		 * - the last V4L2 file handler is closed.
+		 *
+		 * FIXME:
+		 *
+		 * Additionally, this logic could be improved to
+		 * disable the media source if the above conditions
+		 * are met and if the device:
+		 * - doesn't have a separate audio out plug (or
+		 * - doesn't use a silicon tuner like xc2028/3028/4000/5000).
+		 *
+		 * Once this additional logic is in place, a callback
+		 * is needed to enable the media source and power on
+		 * the tuner, for radio to work.
+		*/
+		ret = v4l_enable_media_source(vdev);
+		if (ret == 0)
+			v4l2_device_call_all(&dev->v4l2_dev, 0, core,
+					     s_power, 0);
 		dev->std_set_in_tuner_core = 0;
 
 		/* When close the device, set the usb intf0 into alt0 to free
@@ -1636,10 +1606,16 @@ static int vidioc_s_audio(struct file *file, void *priv, const struct v4l2_audio
 static int vidioc_g_tuner(struct file *file, void *priv, struct v4l2_tuner *t)
 {
 	struct au0828_dev *dev = video_drvdata(file);
+	struct video_device *vfd = video_devdata(file);
+	int ret;
 
 	if (t->index != 0)
 		return -EINVAL;
 
+	ret = v4l_enable_media_source(vfd);
+	if (ret)
+		return ret;
+
 	dprintk(1, "%s called std_set %d dev_state %d\n", __func__,
 		dev->std_set_in_tuner_core, dev->dev_state);