Commit b252f4c7 authored by Bhanu Prakash Gollapudi's avatar Bhanu Prakash Gollapudi Committed by James Bottomley

[SCSI] bnx2fc: Enable REC & CONF support for the session

Based on PRLI response, identify if the target is FCP-2 (seq level error
recovery) capable, and appropriately set the corresponding CONF, REC flags when
offloading the session.
Signed-off-by: default avatarBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: default avatarJames Bottomley <JBottomley@Parallels.com>
parent aea71a02
......@@ -244,9 +244,11 @@ struct bnx2fc_rport {
struct fc_rport_priv *rdata;
void __iomem *ctx_base;
#define DPM_TRIGER_TYPE 0x40
u32 io_timeout;
u32 fcoe_conn_id;
u32 context_id;
u32 sid;
int dev_type;
unsigned long flags;
#define BNX2FC_FLAG_SESSION_READY 0x1
......
......@@ -279,6 +279,18 @@ int bnx2fc_send_session_ofld_req(struct fcoe_port *port,
ofld_req3.flags |= (((rdata->sp_features & FC_SP_FT_SEQC) ? 1 : 0) <<
FCOE_KWQE_CONN_OFFLOAD3_B_CONT_INCR_SEQ_CNT_SHIFT);
/*
* Info from PRLI response, this info is used for sequence level error
* recovery support
*/
if (tgt->dev_type == TYPE_TAPE) {
ofld_req3.flags |= 1 <<
FCOE_KWQE_CONN_OFFLOAD3_B_CONF_REQ_SHIFT;
ofld_req3.flags |= (((rdata->flags & FC_RP_FLAGS_REC_SUPPORTED)
? 1 : 0) <<
FCOE_KWQE_CONN_OFFLOAD3_B_REC_VALID_SHIFT);
}
/* vlan flag */
ofld_req3.flags |= (interface->vlan_enabled <<
FCOE_KWQE_CONN_OFFLOAD3_B_VLAN_FLAG_SHIFT);
......
......@@ -1862,7 +1862,8 @@ static int bnx2fc_post_io_req(struct bnx2fc_rport *tgt,
}
/* Time IO req */
bnx2fc_cmd_timer_set(io_req, BNX2FC_IO_TIMEOUT);
if (tgt->io_timeout)
bnx2fc_cmd_timer_set(io_req, BNX2FC_IO_TIMEOUT);
/* Obtain free SQ entry */
bnx2fc_add_2_sq(tgt, xid);
......
......@@ -353,6 +353,14 @@ static int bnx2fc_init_tgt(struct bnx2fc_rport *tgt,
tgt->rq_cons_idx = 0;
atomic_set(&tgt->num_active_ios, 0);
if (rdata->flags & FC_RP_FLAGS_RETRY) {
tgt->dev_type = TYPE_TAPE;
tgt->io_timeout = 0; /* use default ULP timeout */
} else {
tgt->dev_type = TYPE_DISK;
tgt->io_timeout = BNX2FC_IO_TIMEOUT;
}
/* initialize sq doorbell */
sq_db->header.header = B577XX_DOORBELL_HDR_DB_TYPE;
sq_db->header.header |= B577XX_FCOE_CONNECTION_TYPE <<
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment