Commit b356e978 authored by Sergei Shtylyov's avatar Sergei Shtylyov Committed by David S. Miller

sh_eth: add device tree support

Add support of the device tree probing for the Renesas SH-Mobile SoCs
documenting the device tree binding as necessary.

This work is loosely based on the original patch by Nobuhiro Iwamatsu
<nobuhiro.iwamatsu.yj@renesas.com>.
Signed-off-by: default avatarSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent e8f08ee0
* Renesas Electronics SH EtherMAC
This file provides information on what the device node for the SH EtherMAC
interface contains.
Required properties:
- compatible: "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC.
"renesas,ether-r8a7778" if the device is a part of R8A7778 SoC.
"renesas,ether-r8a7779" if the device is a part of R8A7779 SoC.
"renesas,ether-r8a7790" if the device is a part of R8A7790 SoC.
"renesas,ether-r8a7791" if the device is a part of R8A7791 SoC.
"renesas,ether-r7s72100" if the device is a part of R7S72100 SoC.
- reg: offset and length of (1) the E-DMAC/feLic register block (required),
(2) the TSU register block (optional).
- interrupts: interrupt specifier for the sole interrupt.
- phy-mode: see ethernet.txt file in the same directory.
- phy-handle: see ethernet.txt file in the same directory.
- #address-cells: number of address cells for the MDIO bus, must be equal to 1.
- #size-cells: number of size cells on the MDIO bus, must be equal to 0.
- clocks: clock phandle and specifier pair.
- pinctrl-0: phandle, referring to a default pin configuration node.
Optional properties:
- interrupt-parent: the phandle for the interrupt controller that services
interrupts for this device.
- pinctrl-names: pin configuration state name ("default").
- renesas,no-ether-link: boolean, specify when a board does not provide a proper
Ether LINK signal.
- renesas,ether-link-active-low: boolean, specify when the Ether LINK signal is
active-low instead of normal active-high.
Example (Lager board):
ethernet@ee700000 {
compatible = "renesas,ether-r8a7790";
reg = <0 0xee700000 0 0x400>;
interrupt-parent = <&gic>;
interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7790_CLK_ETHER>;
phy-mode = "rmii";
phy-handle = <&phy1>;
pinctrl-0 = <&ether_pins>;
pinctrl-names = "default";
renesas,ether-link-active-low;
#address-cells = <1>;
#size-cells = <0>;
phy1: ethernet-phy@1 {
reg = <1>;
interrupt-parent = <&irqc0>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
pinctrl-0 = <&phy1_pins>;
pinctrl-names = "default";
};
};
/* SuperH Ethernet device driver
*
* Copyright (C) 2006-2012 Nobuhiro Iwamatsu
* Copyright (C) 2008-2013 Renesas Solutions Corp.
* Copyright (C) 2013 Cogent Embedded, Inc.
* Copyright (C) 2008-2014 Renesas Solutions Corp.
* Copyright (C) 2013-2014 Cogent Embedded, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
......@@ -27,6 +27,10 @@
#include <linux/platform_device.h>
#include <linux/mdio-bitbang.h>
#include <linux/netdevice.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/of_irq.h>
#include <linux/of_net.h>
#include <linux/phy.h>
#include <linux/cache.h>
#include <linux/io.h>
......@@ -2710,6 +2714,54 @@ static const struct net_device_ops sh_eth_netdev_ops_tsu = {
.ndo_change_mtu = eth_change_mtu,
};
#ifdef CONFIG_OF
static struct sh_eth_plat_data *sh_eth_parse_dt(struct device *dev)
{
struct device_node *np = dev->of_node;
struct sh_eth_plat_data *pdata;
struct device_node *phy;
const char *mac_addr;
pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
return NULL;
pdata->phy_interface = of_get_phy_mode(np);
phy = of_parse_phandle(np, "phy-handle", 0);
if (of_property_read_u32(phy, "reg", &pdata->phy))
return NULL;
pdata->phy_irq = irq_of_parse_and_map(phy, 0);
mac_addr = of_get_mac_address(np);
if (mac_addr)
memcpy(pdata->mac_addr, mac_addr, ETH_ALEN);
pdata->no_ether_link =
of_property_read_bool(np, "renesas,no-ether-link");
pdata->ether_link_active_low =
of_property_read_bool(np, "renesas,ether-link-active-low");
return pdata;
}
static const struct of_device_id sh_eth_match_table[] = {
{ .compatible = "renesas,gether-r8a7740", .data = &r8a7740_data },
{ .compatible = "renesas,ether-r8a7778", .data = &r8a777x_data },
{ .compatible = "renesas,ether-r8a7779", .data = &r8a777x_data },
{ .compatible = "renesas,ether-r8a7790", .data = &r8a779x_data },
{ .compatible = "renesas,ether-r8a7791", .data = &r8a779x_data },
{ .compatible = "renesas,ether-r7s72100", .data = &r7s72100_data },
{ }
};
MODULE_DEVICE_TABLE(of, sh_eth_match_table);
#else
static inline struct sh_eth_plat_data *sh_eth_parse_dt(struct device *dev)
{
return NULL;
}
#endif
static int sh_eth_drv_probe(struct platform_device *pdev)
{
int ret, devno = 0;
......@@ -2763,6 +2815,8 @@ static int sh_eth_drv_probe(struct platform_device *pdev)
pm_runtime_enable(&pdev->dev);
pm_runtime_resume(&pdev->dev);
if (pdev->dev.of_node)
pd = sh_eth_parse_dt(&pdev->dev);
if (!pd) {
dev_err(&pdev->dev, "no platform data\n");
ret = -EINVAL;
......@@ -2778,7 +2832,15 @@ static int sh_eth_drv_probe(struct platform_device *pdev)
mdp->ether_link_active_low = pd->ether_link_active_low;
/* set cpu data */
mdp->cd = (struct sh_eth_cpu_data *)id->driver_data;
if (id) {
mdp->cd = (struct sh_eth_cpu_data *)id->driver_data;
} else {
const struct of_device_id *match;
match = of_match_device(of_match_ptr(sh_eth_match_table),
&pdev->dev);
mdp->cd = (struct sh_eth_cpu_data *)match->data;
}
mdp->reg_offset = sh_eth_get_register_offset(mdp->cd->register_type);
sh_eth_set_default_cpu_data(mdp->cd);
......@@ -2920,6 +2982,7 @@ static struct platform_driver sh_eth_driver = {
.driver = {
.name = CARDNAME,
.pm = SH_ETH_PM_OPS,
.of_match_table = of_match_ptr(sh_eth_match_table),
},
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment