Skip to content

L
linux
Commit b35b9a10 authored by Boris Brezillon's avatar Boris Brezillon Committed by Tudor Ambarus
Browse files
Options

mtd: spi-nor: Move m25p80 code in spi-nor.c 

The m25p80 driver is actually a generic wrapper around the spi-mem
layer. Not only the driver name is misleading, but we'd expect such a
common logic to be directly available in the core. Another reason for
moving this code is that SPI NOR controller drivers should
progressively be replaced by SPI controller drivers implementing the
spi_mem_ops interface, and when the conversion is done, we should have
a single spi-nor driver directly interfacing with the spi-mem layer.

While moving the code we also fix a longstanding issue when
non-DMA-able buffers are passed by the MTD layer.
Signed-off-by: default avatarBoris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: default avatarVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: default avatarTudor Ambarus <tudor.ambarus@microchip.com>
parent f173f26a
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 605 additions and 394 deletions
drivers/mtd/devices/Kconfig
View file @ b35b9a10
......@@ -79,24 +79,6 @@ config MTD_DATAFLASH_OTP
other key product data. The second half is programmed with a
unique-to-each-chip bit pattern at the factory.
config MTD_M25P80
tristate "Support most SPI Flash chips (AT26DF, M25P, W25X, ...)"
depends on SPI_MASTER && MTD_SPI_NOR
select SPI_MEM
help
This enables access to most modern SPI flash chips, used for
program and data storage. Series supported include Atmel AT26DF,
Spansion S25SL, SST 25VF, ST M25P, and Winbond W25X. Other chips
are supported as well. See the driver source for the current list,
or to add other chips.
Note that the original DataFlash chips (AT45 series, not AT26DF),
need an entirely different driver.
Set up your spi devices with the right board-specific platform data,
if you want to specify device partitioning or to use a device which
doesn't support the JEDEC ID instruction.
config MTD_MCHP23K256
tristate "Microchip 23K256 SRAM"
depends on SPI_MASTER
......
drivers/mtd/devices/Makefile
View file @ b35b9a10
......@@ -12,7 +12,6 @@ obj-$(CONFIG_MTD_MTDRAM) += mtdram.o
obj-$(CONFIG_MTD_LART) += lart.o
obj-$(CONFIG_MTD_BLOCK2MTD) += block2mtd.o
obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataflash.o
obj-$(CONFIG_MTD_M25P80) += m25p80.o
obj-$(CONFIG_MTD_MCHP23K256) += mchp23k256.o
obj-$(CONFIG_MTD_SPEAR_SMI) += spear_smi.o
obj-$(CONFIG_MTD_SST25L) += sst25l.o
......
drivers/mtd/devices/m25p80.c deleted 100644 → 0
View file @ f173f26a
// SPDX-License-Identifier: GPL-2.0-only
/*
* MTD SPI driver for ST M25Pxx (and similar) serial flash chips
*
* Author: Mike Lavender, mike@steroidmicros.com
*
* Copyright (c) 2005, Intec Automation Inc.
*
* Some parts are based on lart.c by Abraham Van Der Merwe
*
* Cleaned up and generalized based on mtd_dataflash.c
*/
#include <linux/err.h>
#include <linux/errno.h>
#include <linux/module.h>
#include <linux/device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi-mem.h>
#include <linux/spi/flash.h>
#include <linux/mtd/spi-nor.h>
struct m25p {
struct spi_mem *spimem;
struct spi_nor spi_nor;
};
static int m25p80_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len)
{
struct m25p *flash = nor->priv;
struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(code, 1),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_IN(len, NULL, 1));
void *scratchbuf;
int ret;
scratchbuf = kmalloc(len, GFP_KERNEL);
if (!scratchbuf)
return -ENOMEM;
op.data.buf.in = scratchbuf;
ret = spi_mem_exec_op(flash->spimem, &op);
if (ret < 0)
dev_err(&flash->spimem->spi->dev, "error %d reading %x\n", ret,
code);
else
memcpy(val, scratchbuf, len);
kfree(scratchbuf);
return ret;
}
static int m25p80_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
{
struct m25p *flash = nor->priv;
struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 1),
SPI_MEM_OP_NO_ADDR,
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_OUT(len, NULL, 1));
void *scratchbuf;
int ret;
scratchbuf = kmemdup(buf, len, GFP_KERNEL);
if (!scratchbuf)
return -ENOMEM;
op.data.buf.out = scratchbuf;
ret = spi_mem_exec_op(flash->spimem, &op);
kfree(scratchbuf);
return ret;
}
static ssize_t m25p80_write(struct spi_nor *nor, loff_t to, size_t len,
const u_char *buf)
{
struct m25p *flash = nor->priv;
struct spi_mem_op op =
SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 1),
SPI_MEM_OP_ADDR(nor->addr_width, to, 1),
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_OUT(len, buf, 1));
int ret;
/* get transfer protocols. */
op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->write_proto);
op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->write_proto);
op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->write_proto);
if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
op.addr.nbytes = 0;
ret = spi_mem_adjust_op_size(flash->spimem, &op);
if (ret)
return ret;
op.data.nbytes = len < op.data.nbytes ? len : op.data.nbytes;
ret = spi_mem_exec_op(flash->spimem, &op);
if (ret)
return ret;
return op.data.nbytes;
}
/*
* Read an address range from the nor chip. The address range
* may be any size provided it is within the physical boundaries.
*/
static ssize_t m25p80_read(struct spi_nor *nor, loff_t from, size_t len,
u_char *buf)
{
struct m25p *flash = nor->priv;
struct spi_mem_op op =
SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 1),
SPI_MEM_OP_ADDR(nor->addr_width, from, 1),
SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
SPI_MEM_OP_DATA_IN(len, buf, 1));
size_t remaining = len;
int ret;
/* get transfer protocols. */
op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
op.dummy.buswidth = op.addr.buswidth;
op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);
/* convert the dummy cycles to the number of bytes */
op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
while (remaining) {
op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
ret = spi_mem_adjust_op_size(flash->spimem, &op);
if (ret)
return ret;
ret = spi_mem_exec_op(flash->spimem, &op);
if (ret)
return ret;
op.addr.val += op.data.nbytes;
remaining -= op.data.nbytes;
op.data.buf.in += op.data.nbytes;
}
return len;
}
/*
* board specific setup should have ensured the SPI clock used here
* matches what the READ command supports, at least until this driver
* understands FAST_READ (for clocks over 25 MHz).
*/
static int m25p_probe(struct spi_mem *spimem)
{
struct spi_device *spi = spimem->spi;
struct flash_platform_data *data;
struct m25p *flash;
struct spi_nor *nor;
struct spi_nor_hwcaps hwcaps = {
.mask = SNOR_HWCAPS_READ |
SNOR_HWCAPS_READ_FAST |
SNOR_HWCAPS_PP,
};
char *flash_name;
int ret;
data = dev_get_platdata(&spimem->spi->dev);
flash = devm_kzalloc(&spimem->spi->dev, sizeof(*flash), GFP_KERNEL);
if (!flash)
return -ENOMEM;
nor = &flash->spi_nor;
/* install the hooks */
nor->read = m25p80_read;
nor->write = m25p80_write;
nor->write_reg = m25p80_write_reg;
nor->read_reg = m25p80_read_reg;
nor->dev = &spimem->spi->dev;
spi_nor_set_flash_node(nor, spi->dev.of_node);
nor->priv = flash;
spi_mem_set_drvdata(spimem, flash);
flash->spimem = spimem;
if (spi->mode & SPI_RX_OCTAL) {
hwcaps.mask |= SNOR_HWCAPS_READ_1_1_8;
if (spi->mode & SPI_TX_OCTAL)
hwcaps.mask |= (SNOR_HWCAPS_READ_1_8_8 |
SNOR_HWCAPS_PP_1_1_8 |
SNOR_HWCAPS_PP_1_8_8);
} else if (spi->mode & SPI_RX_QUAD) {
hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
if (spi->mode & SPI_TX_QUAD)
hwcaps.mask |= (SNOR_HWCAPS_READ_1_4_4 |
SNOR_HWCAPS_PP_1_1_4 |
SNOR_HWCAPS_PP_1_4_4);
} else if (spi->mode & SPI_RX_DUAL) {
hwcaps.mask |= SNOR_HWCAPS_READ_1_1_2;
if (spi->mode & SPI_TX_DUAL)
hwcaps.mask |= SNOR_HWCAPS_READ_1_2_2;
}
if (data && data->name)
nor->mtd.name = data->name;
if (!nor->mtd.name)
nor->mtd.name = spi_mem_get_name(spimem);
/* For some (historical?) reason many platforms provide two different
* names in flash_platform_data: "name" and "type". Quite often name is
* set to "m25p80" and then "type" provides a real chip name.
* If that's the case, respect "type" and ignore a "name".
*/
if (data && data->type)
flash_name = data->type;
else if (!strcmp(spi->modalias, "spi-nor"))
flash_name = NULL; /* auto-detect */
else
flash_name = spi->modalias;
ret = spi_nor_scan(nor, flash_name, &hwcaps);
if (ret)
return ret;
return mtd_device_register(&nor->mtd, data ? data->parts : NULL,
data ? data->nr_parts : 0);
}
static int m25p_remove(struct spi_mem *spimem)
{
struct m25p *flash = spi_mem_get_drvdata(spimem);
spi_nor_restore(&flash->spi_nor);
/* Clean up MTD stuff. */
return mtd_device_unregister(&flash->spi_nor.mtd);
}
static void m25p_shutdown(struct spi_mem *spimem)
{
struct m25p *flash = spi_mem_get_drvdata(spimem);
spi_nor_restore(&flash->spi_nor);
}
/*
* Do NOT add to this array without reading the following:
*
* Historically, many flash devices are bound to this driver by their name. But
* since most of these flash are compatible to some extent, and their
* differences can often be differentiated by the JEDEC read-ID command, we
* encourage new users to add support to the spi-nor library, and simply bind
* against a generic string here (e.g., "jedec,spi-nor").
*
* Many flash names are kept here in this list (as well as in spi-nor.c) to
* keep them available as module aliases for existing platforms.
*/
static const struct spi_device_id m25p_ids[] = {
/*
* Allow non-DT platform devices to bind to the "spi-nor" modalias, and
* hack around the fact that the SPI core does not provide uevent
* matching for .of_match_table
*/
{"spi-nor"},
/*
* Entries not used in DTs that should be safe to drop after replacing
* them with "spi-nor" in platform data.
*/
{"s25sl064a"}, {"w25x16"}, {"m25p10"}, {"m25px64"},
/*
* Entries that were used in DTs without "jedec,spi-nor" fallback and
* should be kept for backward compatibility.
*/
{"at25df321a"}, {"at25df641"}, {"at26df081a"},
{"mx25l4005a"}, {"mx25l1606e"}, {"mx25l6405d"}, {"mx25l12805d"},
{"mx25l25635e"},{"mx66l51235l"},
{"n25q064"}, {"n25q128a11"}, {"n25q128a13"}, {"n25q512a"},
{"s25fl256s1"}, {"s25fl512s"}, {"s25sl12801"}, {"s25fl008k"},
{"s25fl064k"},
{"sst25vf040b"},{"sst25vf016b"},{"sst25vf032b"},{"sst25wf040"},
{"m25p40"}, {"m25p80"}, {"m25p16"}, {"m25p32"},
{"m25p64"}, {"m25p128"},
{"w25x80"}, {"w25x32"}, {"w25q32"}, {"w25q32dw"},
{"w25q80bl"}, {"w25q128"}, {"w25q256"},
/* Flashes that can't be detected using JEDEC */
{"m25p05-nonjedec"}, {"m25p10-nonjedec"}, {"m25p20-nonjedec"},
{"m25p40-nonjedec"}, {"m25p80-nonjedec"}, {"m25p16-nonjedec"},
{"m25p32-nonjedec"}, {"m25p64-nonjedec"}, {"m25p128-nonjedec"},
/* Everspin MRAMs (non-JEDEC) */
{ "mr25h128" }, /* 128 Kib, 40 MHz */
{ "mr25h256" }, /* 256 Kib, 40 MHz */
{ "mr25h10" }, /* 1 Mib, 40 MHz */
{ "mr25h40" }, /* 4 Mib, 40 MHz */
{ },
};
MODULE_DEVICE_TABLE(spi, m25p_ids);
static const struct of_device_id m25p_of_table[] = {
/*
* Generic compatibility for SPI NOR that can be identified by the
* JEDEC READ ID opcode (0x9F). Use this, if possible.
*/
{ .compatible = "jedec,spi-nor" },
{}
};
MODULE_DEVICE_TABLE(of, m25p_of_table);
static struct spi_mem_driver m25p80_driver = {
.spidrv = {
.driver = {
.name = "m25p80",
.of_match_table = m25p_of_table,
},
.id_table = m25p_ids,
},
.probe = m25p_probe,
.remove = m25p_remove,
.shutdown = m25p_shutdown,
/* REVISIT: many of these chips have deep power-down modes, which
* should clearly be entered on suspend() to minimize power use.
* And also when they're otherwise idle...
*/
};
module_spi_mem_driver(m25p80_driver);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Mike Lavender");
MODULE_DESCRIPTION("MTD SPI driver for ST M25Pxx flash chips");
drivers/mtd/spi-nor/Kconfig
View file @ b35b9a10
......@@ -2,6 +2,8 @@
menuconfig MTD_SPI_NOR
tristate "SPI-NOR device support"
depends on MTD
depends on MTD && SPI_MASTER
select SPI_MEM
help
This is the framework for the SPI NOR which can be used by the SPI
device drivers and the SPI-NOR device driver.
......
drivers/mtd/spi-nor/spi-nor.c
View file @ b35b9a10
This diff is collapsed.
include/linux/mtd/spi-nor.h
View file @ b35b9a10
......@@ -9,6 +9,7 @@
#include <linux/bitops.h>
#include <linux/mtd/cfi.h>
#include <linux/mtd/mtd.h>
#include <linux/spi/spi-mem.h>
/*
* Manufacturer IDs
......@@ -344,6 +345,7 @@ struct flash_info;
* @mtd: point to a mtd_info structure
* @lock: the lock for the read/write/erase/lock/unlock operations
* @dev: point to a spi device, or a spi nor controller device.
* @spimem: point to the spi mem device
* @bouncebuf: bounce buffer used when the buffer passed by the MTD
* layer is not DMA-able
* @bouncebuf_size: size of the bounce buffer
......@@ -384,6 +386,7 @@ struct spi_nor {
struct mtd_info mtd;
struct mutex lock;
struct device *dev;
struct spi_mem *spimem;
u8 *bouncebuf;
size_t bouncebuf_size;
const struct flash_info *info;
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7