Commit b67b3813 authored by Linus Walleij's avatar Linus Walleij

Merge tag 'qcom-pinctrl-6.4' of...

Merge tag 'qcom-pinctrl-6.4' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into devel

Qualcomm pinctrl Devicetree bindings changes for v6.4

Cleanup and improvement of the bindings to use "unevaluatedProperties"
instead of "additionalProperties", which allows to accept all the
properties already parsed by referenced common qcom,tlmm-common.yaml
schema.

That common qcom,tlmm-common.yaml binding is going to remove
"input-enable" property, thus using "unevaluatedProperties" allows such
change to propagate to other bindings automatically.
parents 86169e65 152674ab
No related merge requests found
......@@ -56,6 +56,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -92,19 +93,9 @@ $defs:
rx1, sdc_data, sdc_clk, sdc_cmd, tsens_max, wci_txd, wci_rxd,
wsi_clk, wsi_clk3, wsi_data, wsi_data3, wsis_reset, xfem ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
required:
- compatible
- reg
......
......@@ -43,6 +43,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -89,18 +90,9 @@ $defs:
sd_write, sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2,
uim3, uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -53,6 +53,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -92,19 +93,9 @@ $defs:
qdss_tracedata_b, qpic, rx0, rx1, rx2, sd_card, sd_write,
tsens_max, wci2a, wci2b, wci2c, wci2d ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -54,6 +54,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -105,19 +106,9 @@ $defs:
uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk,
uim2_data, uim2_present, uim2_reset, uim_batt, wlan_en1, ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -51,6 +51,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -70,19 +71,9 @@ $defs:
enum: [ gpio, gsbi2_i2c, gsbi3, gsbi4, gsbi5_i2c, gsbi5_uart,
sdc2, ebi2_lcdc, ps_hold, prim_audio, sec_audio, cdc_mclk, ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
output-high: true
output-low: true
input-enable: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -48,6 +48,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -71,19 +72,9 @@ $defs:
blsp_uart3, blsp_uart4, blsp_uart5, cam_mclk0, cam_mclk1,
gp0_clk, gp1_clk, sdc3, wlan ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -53,6 +53,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -81,20 +82,9 @@ $defs:
sdc5, tsif1, tsif2, usb_fs1, usb_fs1_oe_n, usb_fs2,
usb_fs2_oe_n, vfe, vsens_alarm, ebi2, ebi2cs ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -55,6 +55,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -104,19 +105,9 @@ $defs:
uim3_clk, uim3_data, uim3_present, uim3_reset, uim_batt,
wcss_bt, wcss_fm, wcss_wlan ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -53,6 +53,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -103,19 +104,9 @@ $defs:
uim1, uim2, uim3, uim_batt, wcss_bt, wcss_fm, wcss_wlan,
webcam1_rst ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -45,6 +45,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -106,18 +107,9 @@ $defs:
uim_batt, us_emitter, us_euro, wcss_bt, wcss_fm, wcss_wlan,
wcss_wlan0, wcss_wlan1, wcss_wlan2, wsa_en, wsa_io, wsa_irq ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -53,6 +53,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -97,19 +98,9 @@ $defs:
vfe_camif_timer7_a, vfe_camif_timer7_b, vfe_camif_timer7_c,
wlan ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -53,6 +53,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -93,14 +94,6 @@ $defs:
tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s,
spkr_mi2s, ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
......@@ -124,8 +117,6 @@ $defs:
output-high: false
output-low: false
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -53,6 +53,7 @@ $defs:
Desired pin configuration for a device or its specific state (like sleep
or active).
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -93,19 +94,9 @@ $defs:
wsa_irq, blsp_i2c8, pa_indicator, modem_tsync, ssbi_wtr1,
gsm1_tx, gsm0_tx, sdcard_det, sec_mi2s, ss_switch ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -55,6 +55,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -103,19 +104,9 @@ $defs:
pri_mi2s, sdc4, sec_mi2s, slimbus, spkr_i2s, ter_mi2s, tsif1,
tsif2, uim_batt_alarm, uim1, uim2, uim3, uim4 ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -53,6 +53,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -122,19 +123,9 @@ $defs:
modem_tsync, nav_dr, nav_pps, pci_e1, gsm_tx, qspi_cs, ssbi2,
ssbi1, mss_lte, qspi_clk, qspi0, qspi1, qspi2, qspi3 ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -53,6 +53,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -107,19 +108,9 @@ $defs:
vsense_clkout, vsense_data0, vsense_data1, vsense_mode,
wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -59,6 +59,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -119,19 +120,9 @@ $defs:
spdifrx_opt, spi_lcd, spkr_dac0, wlan1_adc0, wlan1_adc1,
wlan2_adc0, wlan2_adc1, wsa_en ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -55,6 +55,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -93,19 +94,9 @@ $defs:
usb2phy_ac, usb_con_det, usb_dfp_en, usb_phy, vfr_0, vfr_1,
vsense_trigger ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
required:
- compatible
- reg
......
......@@ -58,6 +58,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -103,19 +104,9 @@ $defs:
tgu_ch2, tgu_ch3, tgu_ch4, tgu_ch5, tsense_pwm1, tsense_pwm2,
tsense_pwm3, tsense_pwm4, usb2phy_ac, vsense_trigger ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -59,6 +59,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -100,19 +101,9 @@ $defs:
_V_GPIO, _V_PPS_IN, _V_PPS_OUT, vsense_trigger, wlan1_adc0,
wlan1_adc1, wlan2_adc0, wlan2_adc1 ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -62,6 +62,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -110,20 +111,9 @@ $defs:
uim1_clk, uim1_data, uim1_present, uim1_reset, usb2phy_ac,
usb_phy, vfr_0, vfr_1, vsense_trigger ]
bias-pull-down: true
bias-pull-up: true
bias-bus-hold: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -62,6 +62,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -102,19 +103,9 @@ $defs:
usb0_phy, usb1_phy, usb2phy_ac, vfr_1, vsense_trigger,
wlan1_adc, wlan2_adc, wmss_reset ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -65,6 +65,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -122,19 +123,9 @@ $defs:
vsense_data0, vsense_data1, vsense_mode, wlan1_adc0,
wlan1_adc1, wlan2_adc0, wlan2_adc1 ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
required:
- compatible
- reg
......
......@@ -58,6 +58,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -94,20 +95,9 @@ $defs:
uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset, uim_batt, usb_phy, vfr_1,
vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1, wsa_clk, wsa_data, ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -61,6 +61,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -102,19 +103,9 @@ $defs:
uim_batt, usb_phy, vfr_1, vsense_trigger, wlan1_adc0,
wlan1_adc1, wlan2_adc0, wlan2_adc1]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
required:
- compatible
- reg
......
......@@ -48,6 +48,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -91,18 +92,9 @@ $defs:
uim1_present, uim1_reset, uim2_clk, uim2_data, uim2_present,
uim2_reset, usb2phy_ac, vsense_trigger ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -47,6 +47,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -111,18 +112,9 @@ $defs:
qspi_cs, ssbi2, ssbi1, mss_lte, qspi_clk, qspi0, qspi1, qspi2, qspi3,
gpio ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -53,6 +53,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -85,18 +86,9 @@ $defs:
uim2_present, uim2_reset, usb_phy, vfr_1, vsense_trigger,
wlan1_adc0, elan1_adc1 ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -61,6 +61,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -101,19 +102,9 @@ $defs:
wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1, wsa_clk, wsa_data ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -63,6 +63,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -108,20 +109,9 @@ $defs:
uim2_present, uim2_reset, usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1,
wlan2_adc0, wlan2_adc1, ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -55,6 +55,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -109,20 +110,9 @@ $defs:
usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1,
wlan2_adc0, wlan2_adc1 ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -60,6 +60,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -101,19 +102,9 @@ $defs:
usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1,
wlan2_adc0, wlan2_adc1, wmss_reset ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -58,6 +58,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -94,19 +95,9 @@ $defs:
tsif0_en, tsif0_error, tsif0_sync, tsif1_clk, tsif1_data, tsif1_en,
tsif1_error, tsif1_sync, usb2phy_ac, usb_phy, vsense_trigger ]
bias-pull-down: true
bias-pull-up: true
bias-disable: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
allOf:
- $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
......
......@@ -62,6 +62,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -104,21 +105,9 @@ $defs:
uim0_present, uim0_reset, uim1_clk, uim1_data, uim1_present,
uim1_reset, usb2phy_ac, usb_phy, vfr_0, vfr_1, vsense_trigger ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-disable: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -62,6 +62,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -103,19 +104,9 @@ $defs:
uim0_reset, uim1_clk, uim1_data, uim1_present, uim1_reset,
usb2phy_ac, usb_phy, vfr_0, vfr_1, vsense_trigger ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
......
......@@ -54,6 +54,7 @@ $defs:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
unevaluatedProperties: false
properties:
pins:
......@@ -109,19 +110,9 @@ $defs:
uim1_clk, uim1_data, uim1_present, uim1_reset,
usb1_hs, usb_phy, vfr_0, vfr_1, vsense_trigger_mirnat ]
bias-disable: true
bias-pull-down: true
bias-pull-up: true
drive-strength: true
input-enable: true
output-high: true
output-low: true
required:
- pins
additionalProperties: false
required:
- compatible
- reg
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment