Commit b690bdef authored by Krzysztof Halasa's avatar Krzysztof Halasa Committed by Jeff Garzik

[PATCH] WAN: DSCC4 driver requires generic HDLC

Another thing, reported recently to me by several people - DSCC4 WAN
driver now (and perhaps for the last couple of years+) requires the
generic HDLC. I've fixed the Kconfig and moved the DSCC4 option
under CONFIG_HDLC so it's consistent visually.
Signed-off-by: default avatarKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
parent 5e123b84
...@@ -57,44 +57,6 @@ config COSA ...@@ -57,44 +57,6 @@ config COSA
The driver will be compiled as a module: the The driver will be compiled as a module: the
module will be called cosa. module will be called cosa.
config DSCC4
tristate "Etinc PCISYNC serial board support"
depends on WAN && PCI && m
help
Driver for Etinc PCISYNC boards based on the Infineon (ex. Siemens)
DSCC4 chipset.
This is supposed to work with the four port card. Take a look at
<http://www.cogenit.fr/dscc4/> for further information about the
driver.
To compile this driver as a module, choose M here: the
module will be called dscc4.
config DSCC4_PCISYNC
bool "Etinc PCISYNC features"
depends on DSCC4
help
Due to Etinc's design choice for its PCISYNC cards, some operations
are only allowed on specific ports of the DSCC4. This option is the
only way for the driver to know that it shouldn't return a success
code for these operations.
Please say Y if your card is an Etinc's PCISYNC.
config DSCC4_PCI_RST
bool "Hard reset support"
depends on DSCC4
help
Various DSCC4 bugs forbid any reliable software reset of the ASIC.
As a replacement, some vendors provide a way to assert the PCI #RST
pin of DSCC4 through the GPIO port of the card. If you choose Y,
the driver will make use of this feature before module removal
(i.e. rmmod). The feature is known to be available on Commtech's
cards. Contact your manufacturer for details.
Say Y if your card supports this feature.
# #
# Lan Media's board. Currently 1000, 1200, 5200, 5245 # Lan Media's board. Currently 1000, 1200, 5200, 5245
# #
...@@ -323,6 +285,44 @@ config FARSYNC ...@@ -323,6 +285,44 @@ config FARSYNC
To compile this driver as a module, choose M here: the To compile this driver as a module, choose M here: the
module will be called farsync. module will be called farsync.
config DSCC4
tristate "Etinc PCISYNC serial board support"
depends on HDLC && PCI && m
help
Driver for Etinc PCISYNC boards based on the Infineon (ex. Siemens)
DSCC4 chipset.
This is supposed to work with the four port card. Take a look at
<http://www.cogenit.fr/dscc4/> for further information about the
driver.
To compile this driver as a module, choose M here: the
module will be called dscc4.
config DSCC4_PCISYNC
bool "Etinc PCISYNC features"
depends on DSCC4
help
Due to Etinc's design choice for its PCISYNC cards, some operations
are only allowed on specific ports of the DSCC4. This option is the
only way for the driver to know that it shouldn't return a success
code for these operations.
Please say Y if your card is an Etinc's PCISYNC.
config DSCC4_PCI_RST
bool "Hard reset support"
depends on DSCC4
help
Various DSCC4 bugs forbid any reliable software reset of the ASIC.
As a replacement, some vendors provide a way to assert the PCI #RST
pin of DSCC4 through the GPIO port of the card. If you choose Y,
the driver will make use of this feature before module removal
(i.e. rmmod). The feature is known to be available on Commtech's
cards. Contact your manufacturer for details.
Say Y if your card supports this feature.
config DLCI config DLCI
tristate "Frame Relay DLCI support" tristate "Frame Relay DLCI support"
depends on WAN depends on WAN
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment