[PATCH] WAN: DSCC4 driver requires generic HDLC

Another thing, reported recently to me by several people - DSCC4 WAN
driver now (and perhaps for the last couple of years+) requires the
generic HDLC. I've fixed the Kconfig and moved the DSCC4 option
under CONFIG_HDLC so it's consistent visually.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/net/wan/Kconfig

@@ -57,44 +57,6 @@ config COSA
 	  The driver will be compiled as a module: the
 	  module will be called cosa.
 
-config DSCC4
-	tristate "Etinc PCISYNC serial board support"
-	depends on WAN && PCI && m
-	help
-	  Driver for Etinc PCISYNC boards based on the Infineon (ex. Siemens)
-	  DSCC4 chipset.
-
-	  This is supposed to work with the four port card. Take a look at
-	  <http://www.cogenit.fr/dscc4/> for further information about the
-	  driver.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called dscc4.
-
-config DSCC4_PCISYNC
-	bool "Etinc PCISYNC features"
-	depends on DSCC4
-	help
-	  Due to Etinc's design choice for its PCISYNC cards, some operations
-	  are only allowed on specific ports of the DSCC4. This option is the
-	  only way for the driver to know that it shouldn't return a success
-	  code for these operations.
-
-	  Please say Y if your card is an Etinc's PCISYNC.
-
-config DSCC4_PCI_RST
-	bool "Hard reset support"
-	depends on DSCC4
-	help
-	  Various DSCC4 bugs forbid any reliable software reset of the ASIC.
-	  As a replacement, some vendors provide a way to assert the PCI #RST
-	  pin of DSCC4 through the GPIO port of the card. If you choose Y,
-	  the driver will make use of this feature before module removal
-	  (i.e. rmmod). The feature is known to be available on Commtech's
-	  cards. Contact your manufacturer for details.
-
-	  Say Y if your card supports this feature.
-
 #
 # Lan Media's board. Currently 1000, 1200, 5200, 5245
 #
@@ -323,6 +285,44 @@ config FARSYNC
 	  To compile this driver as a module, choose M here: the
 	  module will be called farsync.
 
+config DSCC4
+	tristate "Etinc PCISYNC serial board support"
+	depends on HDLC && PCI && m
+	help
+	  Driver for Etinc PCISYNC boards based on the Infineon (ex. Siemens)
+	  DSCC4 chipset.
+
+	  This is supposed to work with the four port card. Take a look at
+	  <http://www.cogenit.fr/dscc4/> for further information about the
+	  driver.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called dscc4.
+
+config DSCC4_PCISYNC
+	bool "Etinc PCISYNC features"
+	depends on DSCC4
+	help
+	  Due to Etinc's design choice for its PCISYNC cards, some operations
+	  are only allowed on specific ports of the DSCC4. This option is the
+	  only way for the driver to know that it shouldn't return a success
+	  code for these operations.
+
+	  Please say Y if your card is an Etinc's PCISYNC.
+
+config DSCC4_PCI_RST
+	bool "Hard reset support"
+	depends on DSCC4
+	help
+	  Various DSCC4 bugs forbid any reliable software reset of the ASIC.
+	  As a replacement, some vendors provide a way to assert the PCI #RST
+	  pin of DSCC4 through the GPIO port of the card. If you choose Y,
+	  the driver will make use of this feature before module removal
+	  (i.e. rmmod). The feature is known to be available on Commtech's
+	  cards. Contact your manufacturer for details.
+
+	  Say Y if your card supports this feature.
+
 config DLCI
 	tristate "Frame Relay DLCI support"
 	depends on WAN