usb: xhci: define port register names and use them instead of magic numbers

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>

drivers/usb/host/xhci-hub.c

@@ -867,18 +867,18 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 		case USB_PORT_FEAT_U1_TIMEOUT:
 			if (hcd->speed != HCD_USB3)
 				goto error;
-			temp = xhci_readl(xhci, port_array[wIndex] + 1);
+			temp = xhci_readl(xhci, port_array[wIndex] + PORTPMSC);
 			temp &= ~PORT_U1_TIMEOUT_MASK;
 			temp |= PORT_U1_TIMEOUT(timeout);
-			xhci_writel(xhci, temp, port_array[wIndex] + 1);
+			xhci_writel(xhci, temp, port_array[wIndex] + PORTPMSC);
 			break;
 		case USB_PORT_FEAT_U2_TIMEOUT:
 			if (hcd->speed != HCD_USB3)
 				goto error;
-			temp = xhci_readl(xhci, port_array[wIndex] + 1);
+			temp = xhci_readl(xhci, port_array[wIndex] + PORTPMSC);
 			temp &= ~PORT_U2_TIMEOUT_MASK;
 			temp |= PORT_U2_TIMEOUT(timeout);
-			xhci_writel(xhci, temp, port_array[wIndex] + 1);
+			xhci_writel(xhci, temp, port_array[wIndex] + PORTPMSC);
 			break;
 		default:
 			goto error;
@@ -1098,10 +1098,8 @@ int xhci_bus_suspend(struct usb_hcd *hcd)
 			__le32 __iomem *addr;
 			u32 tmp;
 
-			/* Add one to the port status register address to get
-			 * the port power control register address.
-			 */
-			addr = port_array[port_index] + 1;
+			/* Get the port power control register address. */
+			addr = port_array[port_index] + PORTPMSC;
 			tmp = xhci_readl(xhci, addr);
 			tmp |= PORT_RWE;
 			xhci_writel(xhci, tmp, addr);
@@ -1193,7 +1191,7 @@ int xhci_bus_resume(struct usb_hcd *hcd)
 			/* Add one to the port status register address to get
 			 * the port power control register address.
 			 */
-			addr = port_array[port_index] + 1;
+			addr = port_array[port_index] + PORTPMSC;
 			tmp = xhci_readl(xhci, addr);
 			tmp &= ~PORT_RWE;
 			xhci_writel(xhci, tmp, addr);

drivers/usb/host/xhci.c

@@ -3911,7 +3911,7 @@ static int xhci_usb2_software_lpm_test(struct usb_hcd *hcd,
 	 * Check device's USB 2.0 extension descriptor to determine whether
 	 * HIRD or BESL shoule be used. See USB2.0 LPM errata.
 	 */
-	pm_addr = port_array[port_num] + 1;
+	pm_addr = port_array[port_num] + PORTPMSC;
 	hird = xhci_calculate_hird_besl(xhci, udev);
 	temp = PORT_L1DS(udev->slot_id) | PORT_HIRD(hird);
 	xhci_writel(xhci, temp, pm_addr);
@@ -4009,7 +4009,7 @@ int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
 
 	port_array = xhci->usb2_ports;
 	port_num = udev->portnum - 1;
-	pm_addr = port_array[port_num] + 1;
+	pm_addr = port_array[port_num] + PORTPMSC;
 	temp = xhci_readl(xhci, pm_addr);
 
 	xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",

drivers/usb/host/xhci.h

@@ -132,6 +132,11 @@ struct xhci_cap_regs {
 /* Number of registers per port */
 #define	NUM_PORT_REGS	4
 
+#define PORTSC		0
+#define PORTPMSC	1
+#define PORTLI		2
+#define PORTHLPMC	3
+
 /**
  * struct xhci_op_regs - xHCI Host Controller Operational Registers.
  * @command:		USBCMD - xHC command register