Commit b9a35d70 authored by Linus Walleij's avatar Linus Walleij

ARM: dts: Add some initial IXP4xx device trees

This adds a device tree for the IXP4xx-based Linksys
NSLU2 and Gateworks GW2358 which encompass the Gateworks
Cambria family.

These will be the first IXP4xx device tree platforms.
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent 9540724c
......@@ -229,6 +229,9 @@ dtb-$(CONFIG_ARCH_HIX5HD2) += \
dtb-$(CONFIG_ARCH_INTEGRATOR) += \
integratorap.dtb \
integratorcp.dtb
dtb-$(CONFIG_ARCH_IXP4XX) += \
intel-ixp42x-linksys-nslu2.dtb \
intel-ixp43x-gateworks-gw2358.dtb
dtb-$(CONFIG_ARCH_KEYSTONE) += \
keystone-k2hk-evm.dtb \
keystone-k2l-evm.dtb \
......
// SPDX-License-Identifier: ISC
/*
* Device Tree file for Linksys NSLU2
*/
/dts-v1/;
#include "intel-ixp42x.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "Linksys NSLU2 (Network Storage Link for USB 2.0 Disk Drives)";
compatible = "linksys,nslu2", "intel,ixp42x";
#address-cells = <1>;
#size-cells = <1>;
memory@0 {
/* 32 MB SDRAM */
device_type = "memory";
reg = <0x00000000 0x2000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
stdout-path = "uart0:115200n8";
};
aliases {
serial0 = &uart0;
};
leds {
compatible = "gpio-leds";
led-status {
label = "nslu2:red:status";
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
led-ready {
label = "nslu2:green:ready";
gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
led-disk-1 {
label = "nslu2:green:disk-1";
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led-disk-2 {
label = "nslu2:green:disk-2";
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
default-state = "off";
};
};
gpio_keys {
compatible = "gpio-keys";
button-power {
wakeup-source;
linux,code = <KEY_POWER>;
label = "power";
gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
};
button-reset {
wakeup-source;
linux,code = <KEY_ESC>;
label = "reset";
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
};
};
i2c {
compatible = "i2c-gpio";
sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
#address-cells = <1>;
#size-cells = <0>;
rtc@6f {
compatible = "xicor,x1205";
reg = <0x6f>;
};
};
gpio-poweroff {
compatible = "gpio-poweroff";
gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
timeout-ms = <5000>;
};
/* The first 16MB region on the expansion bus */
flash@50000000 {
compatible = "intel,ixp4xx-flash", "cfi-flash";
bank-width = <2>;
/*
* 8 MB of Flash in 0x20000 byte blocks
* mapped in at 0x50000000
*/
reg = <0x50000000 0x800000>;
partitions {
compatible = "redboot-fis";
/* Eraseblock at 0x7e0000 */
fis-index-block = <0x3f>;
};
};
};
// SPDX-License-Identifier: ISC
/*
* Device Tree file for Intel XScale Network Processors
* in the IXP 42x series. This series has 32 interrupts.
*/
#include "intel-ixp4xx.dtsi"
/ {
soc {
interrupt-controller@c8003000 {
compatible = "intel,ixp42x-interrupt";
};
/*
* This is the USB Device Mode (UDC) controller, which is used
* to present the IXP4xx as a device on a USB bus.
*/
usb@c800b000 {
compatible = "intel,ixp4xx-udc";
reg = <0xc800b000 0x1000>;
interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
};
};
// SPDX-License-Identifier: ISC
/*
* Device Tree file for Gateworks IXP43x-based Cambria GW2358
*/
/dts-v1/;
#include "intel-ixp43x.dtsi"
/ {
model = "Gateworks Cambria GW2358";
compatible = "gateworks,gw2358", "intel,ixp43x";
#address-cells = <1>;
#size-cells = <1>;
memory@0 {
/* 128 MB SDRAM */
device_type = "memory";
reg = <0x00000000 0x8000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
stdout-path = "uart0:115200n8";
};
aliases {
serial0 = &uart0;
};
leds {
compatible = "gpio-leds";
led-user {
label = "gw2358:green:LED";
gpios = <&pld1 0 GPIO_ACTIVE_LOW>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
};
i2c {
compatible = "i2c-gpio";
sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
#address-cells = <1>;
#size-cells = <0>;
hwmon@28 {
compatible = "adi,ad7418";
reg = <0x28>;
};
rtc: ds1672@68 {
compatible = "dallas,ds1672";
reg = <0x68>;
};
eeprom@51 {
compatible = "atmel,24c08";
reg = <0x51>;
pagesize = <16>;
size = <1024>;
read-only;
};
pld0: pld@56 {
compatible = "gateworks,pld-gpio";
reg = <0x56>;
gpio-controller;
#gpio-cells = <2>;
};
/* This PLD just handles the LED and user button */
pld1: pld@57 {
compatible = "gateworks,pld-gpio";
reg = <0x57>;
gpio-controller;
#gpio-cells = <2>;
};
};
flash@50000000 {
compatible = "intel,ixp4xx-flash", "cfi-flash";
bank-width = <2>;
/*
* 32 MB of Flash in 0x20000 byte blocks
* mapped in at 0x50000000
*/
reg = <0x50000000 0x2000000>;
partitions {
compatible = "redboot-fis";
/* Eraseblock at 0x1fe0000 */
fis-index-block = <0xff>;
};
};
};
// SPDX-License-Identifier: ISC
/*
* Device Tree file for Intel XScale Network Processors
* in the IXP 43x series. This series has 64 interrupts and adds a few more
* peripherals over the 42x series.
*/
#include "intel-ixp4xx.dtsi"
/ {
soc {
interrupt-controller@c8003000 {
compatible = "intel,ixp43x-interrupt";
};
};
};
// SPDX-License-Identifier: ISC
/*
* Device Tree file for Intel XScale Network Processors
* in the IXP45x and IXP46x series. This series has 64 interrupts and adds a
* few more peripherals over the 42x and 43x series so this extends the
* basic IXP4xx DTSI.
*/
#include "intel-ixp4xx.dtsi"
/ {
soc {
interrupt-controller@c8003000 {
compatible = "intel,ixp43x-interrupt";
};
/*
* This is the USB Device Mode (UDC) controller, which is used
* to present the IXP4xx as a device on a USB bus.
*/
usb@c800b000 {
compatible = "intel,ixp4xx-udc";
reg = <0xc800b000 0x1000>;
interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
i2c@c8011000 {
compatible = "intel,ixp4xx-i2c";
reg = <0xc8011000 0x18>;
interrupts = <33 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
};
};
// SPDX-License-Identifier: ISC
/*
* Device Tree file for Intel XScale Network Processors
* in the IXP 4xx series.
*/
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
/ {
soc {
#address-cells = <1>;
#size-cells = <1>;
ranges;
compatible = "simple-bus";
interrupt-parent = <&intcon>;
uart0: serial@c8000000 {
compatible = "intel,xscale-uart";
reg = <0xc8000000 0x1000>;
/*
* The reg-offset and reg-shift is a side effect
* of running the platform in big endian mode.
*/
reg-offset = <3>;
reg-shift = <2>;
interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <14745600>;
no-loopback-test;
};
gpio0: gpio@c8004000 {
compatible = "intel,ixp4xx-gpio";
reg = <0xc8004000 0x1000>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
intcon: interrupt-controller@c8003000 {
/*
* Note: no compatible string. The subvariant of the
* chip needs to define what version it is. The
* location of the interrupt controller is fixed in
* memory across all variants.
*/
reg = <0xc8003000 0x100>;
interrupt-controller;
#interrupt-cells = <2>;
};
timer@c8005000 {
compatible = "intel,ixp4xx-timer";
reg = <0xc8005000 0x100>;
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
};
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment