Merge tag 'tags/bcm2835-dt-next-2018-09-09' into devicetree/next

This pull request brings in a board DT for the Raspberry Pi Compute
Module 3, its I/O board and enables the Ethernet LEDs for the RPi 3B+.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt

@@ -42,6 +42,14 @@ Raspberry Pi Compute Module
 Required root node properties:
 compatible = "raspberrypi,compute-module", "brcm,bcm2835";
 
+Raspberry Pi Compute Module 3
+Required root node properties:
+compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+
+Raspberry Pi Compute Module 3 Lite
+Required root node properties:
+compatible = "raspberrypi,3-compute-module-lite", "brcm,bcm2837";
+
 Raspberry Pi Zero
 Required root node properties:
 compatible = "raspberrypi,model-zero", "brcm,bcm2835";

arch/arm/boot/dts/Makefile

@@ -81,6 +81,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2836-rpi-2-b.dtb \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
+	bcm2837-rpi-cm3-io3.dtb \
 	bcm2835-rpi-zero.dtb \
 	bcm2835-rpi-zero-w.dtb
 dtb-$(CONFIG_ARCH_BCM_5301X) += \

arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts

+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837-rpi-cm3.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+	model = "Raspberry Pi Compute Module 3 IO board V3.0";
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "GPIO0",
+			  "GPIO1",
+			  "GPIO2",
+			  "GPIO3",
+			  "GPIO4",
+			  "GPIO5",
+			  "GPIO6",
+			  "GPIO7",
+			  "GPIO8",
+			  "GPIO9",
+			  "GPIO10",
+			  "GPIO11",
+			  "GPIO12",
+			  "GPIO13",
+			  "GPIO14",
+			  "GPIO15",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "GPIO32",
+			  "GPIO33",
+			  "GPIO34",
+			  "GPIO35",
+			  "GPIO36",
+			  "GPIO37",
+			  "GPIO38",
+			  "GPIO39",
+			  "GPIO40",
+			  "GPIO41",
+			  "GPIO42",
+			  "GPIO43",
+			  "GPIO44",
+			  "GPIO45",
+			  "GPIO46",
+			  "GPIO47",
+			  /* Used by eMMC */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};

arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi

+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	reg_3v3: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_1v8: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "HDMI_HPD_N",
+				  "EMMC_EN_N",
+				  "NC",
+				  "NC",
+				  "NC",
+				  "NC",
+				  "NC",
+				  "NC";
+		status = "okay";
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_1v8>;
+	status = "okay";
+};

arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi

 // SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/net/microchip-lan78xx.h>
+
 / {
 	aliases {
 		ethernet0 = &ethernet;
@@ -21,6 +23,18 @@ usb-port@1 {
 			ethernet: ethernet@1 {
 				compatible = "usb424,7800";
 				reg = <1>;
+
+				mdio {
+					#address-cells = <0x1>;
+					#size-cells = <0x0>;
+					eth_phy: ethernet-phy@1 {
+						reg = <1>;
+						microchip,led-modes = <
+							LAN78XX_LINK_1000_ACTIVITY
+							LAN78XX_LINK_10_100_ACTIVITY
+						>;
+					};
+				};
 			};
 		};
 	};