Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull more i2c updates from Wolfram Sang:
 "I2C has two more new drivers: Altera FPGA and STM32F7"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i2c-stm32f7: add driver
  i2c: i2c-stm32f4: use generic definition of speed enum
  dt-bindings: i2c-stm32: Document the STM32F7 I2C bindings
  i2c: altera: Add Altera I2C Controller driver
  dt-bindings: i2c: Add Altera I2C Controller

Documentation/devicetree/bindings/i2c/i2c-altera.txt

+* Altera I2C Controller
+* This is Altera's synthesizable logic block I2C Controller for use
+* in Altera's FPGAs.
+
+Required properties :
+ - compatible : should be "altr,softip-i2c-v1.0"
+ - reg        : Offset and length of the register set for the device
+ - interrupts : <IRQ> where IRQ is the interrupt number.
+ - clocks     : phandle to input clock.
+ - #address-cells = <1>;
+ - #size-cells = <0>;
+
+Recommended properties :
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+
+Optional properties :
+ - fifo-size : Size of the RX and TX FIFOs in bytes.
+ - Child nodes conforming to i2c bus binding
+
+Example :
+
+	i2c@100080000 {
+		compatible = "altr,softip-i2c-v1.0";
+		reg = <0x00000001 0x00080000 0x00000040>;
+		interrupt-parent = <&intc>;
+		interrupts = <0 43 4>;
+		clocks = <&clk_0>;
+		clock-frequency = <100000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		fifo-size = <4>;
+
+		eeprom@51 {
+			compatible = "atmel,24c32";
+			reg = <0x51>;
+			pagesize = <32>;
+		};
+	};
+

Documentation/devicetree/bindings/i2c/i2c-stm32.txt

 * I2C controller embedded in STMicroelectronics STM32 I2C platform
 
 Required properties :
-- compatible : Must be "st,stm32f4-i2c"
+- compatible : Must be one of the following
+  - "st,stm32f4-i2c"
+  - "st,stm32f7-i2c"
 - reg : Offset and length of the register set for the device
 - interrupts : Must contain the interrupt id for I2C event and then the
   interrupt id for I2C error.
@@ -14,8 +16,16 @@ Required properties :
 
 Optional properties :
 - clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
-  the default 100 kHz frequency will be used. As only Normal and Fast modes
-  are supported, possible values are 100000 and 400000.
+  the default 100 kHz frequency will be used.
+  For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are
+  100000 and 400000.
+  For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported,
+  possible values are 100000, 400000 and 1000000.
+- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board
+  (default: 25)
+- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board
+  (default: 10)
+  I2C Timings are derived from these 2 values
 
 Example :
 
@@ -31,3 +41,16 @@ Example :
 		pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
 		pinctrl-names = "default";
 	};
+
+	i2c@40005400 {
+		compatible = "st,stm32f7-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x40005400 0x400>;
+		interrupts = <31>,
+			     <32>;
+		resets = <&rcc STM32F7_APB1_RESET(I2C1)>;
+		clocks = <&rcc 1 CLK_I2C1>;
+		pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
+		pinctrl-names = "default";
+	};

MAINTAINERS

@@ -644,6 +644,11 @@ ALPS PS/2 TOUCHPAD DRIVER
 R:	Pali Rohár <pali.rohar@gmail.com>
 F:	drivers/input/mouse/alps.*
 
+ALTERA I2C CONTROLLER DRIVER
+M:	Thor Thayer <thor.thayer@linux.intel.com>
+S:	Maintained
+F:	drivers/i2c/busses/i2c-altera.c
+
 ALTERA MAILBOX DRIVER
 M:	Ley Foon Tan <lftan@altera.com>
 L:	nios2-dev@lists.rocketboards.org (moderated for non-subscribers)

drivers/i2c/busses/Kconfig

@@ -336,6 +336,16 @@ config I2C_POWERMAC
 
 comment "I2C system bus drivers (mostly embedded / system-on-chip)"
 
+config I2C_ALTERA
+	tristate "Altera Soft IP I2C"
+	depends on (ARCH_SOCFPGA || NIOS2) && OF
+	help
+	  If you say yes to this option, support will be included for the
+	  Altera Soft IP I2C interfaces on SoCFPGA and Nios2 architectures.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-altera.
+
 config I2C_ASPEED
 	tristate "Aspeed I2C Controller"
 	depends on ARCH_ASPEED || COMPILE_TEST
@@ -935,6 +945,16 @@ config I2C_STM32F4
 	  This driver can also be built as module. If so, the module
 	  will be called i2c-stm32f4.
 
+config I2C_STM32F7
+	tristate "STMicroelectronics STM32F7 I2C support"
+	depends on ARCH_STM32 || COMPILE_TEST
+	help
+	  Enable this option to add support for STM32 I2C controller embedded
+	  in STM32F7 SoCs.
+
+	  This driver can also be built as module. If so, the module
+	  will be called i2c-stm32f7.
+
 config I2C_STU300
 	tristate "ST Microelectronics DDC I2C interface"
 	depends on MACH_U300

drivers/i2c/busses/Makefile

@@ -30,6 +30,7 @@ obj-$(CONFIG_I2C_HYDRA)		+= i2c-hydra.o
 obj-$(CONFIG_I2C_POWERMAC)	+= i2c-powermac.o
 
 # Embedded system I2C/SMBus host controller drivers
+obj-$(CONFIG_I2C_ALTERA)	+= i2c-altera.o
 obj-$(CONFIG_I2C_ASPEED)	+= i2c-aspeed.o
 obj-$(CONFIG_I2C_AT91)		+= i2c-at91.o
 obj-$(CONFIG_I2C_AU1550)	+= i2c-au1550.o
@@ -93,6 +94,7 @@ obj-$(CONFIG_I2C_SIRF)		+= i2c-sirf.o
 obj-$(CONFIG_I2C_SPRD)		+= i2c-sprd.o
 obj-$(CONFIG_I2C_ST)		+= i2c-st.o
 obj-$(CONFIG_I2C_STM32F4)	+= i2c-stm32f4.o
+obj-$(CONFIG_I2C_STM32F7)	+= i2c-stm32f7.o
 obj-$(CONFIG_I2C_STU300)	+= i2c-stu300.o
 obj-$(CONFIG_I2C_SUN6I_P2WI)	+= i2c-sun6i-p2wi.o
 obj-$(CONFIG_I2C_TEGRA)		+= i2c-tegra.o

drivers/i2c/busses/i2c-stm32.h

+/*
+ * i2c-stm32.h
+ *
+ * Copyright (C) M'boumba Cedric Madianga 2017
+ * Author: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
+ *
+ * License terms:  GNU General Public License (GPL), version 2
+ */
+
+#ifndef _I2C_STM32_H
+#define _I2C_STM32_H
+
+enum stm32_i2c_speed {
+	STM32_I2C_SPEED_STANDARD, /* 100 kHz */
+	STM32_I2C_SPEED_FAST, /* 400 kHz */
+	STM32_I2C_SPEED_FAST_PLUS, /* 1 MHz */
+	STM32_I2C_SPEED_END,
+};
+
+#endif /* _I2C_STM32_H */

drivers/i2c/busses/i2c-stm32f4.c

@@ -27,6 +27,8 @@
 #include <linux/platform_device.h>
 #include <linux/reset.h>
 
+#include "i2c-stm32.h"
+
 /* STM32F4 I2C offset registers */
 #define STM32F4_I2C_CR1			0x00
 #define STM32F4_I2C_CR2			0x04
@@ -90,12 +92,6 @@
 #define STM32F4_I2C_MAX_FREQ		46U
 #define HZ_TO_MHZ			1000000
 
-enum stm32f4_i2c_speed {
-	STM32F4_I2C_SPEED_STANDARD, /* 100 kHz */
-	STM32F4_I2C_SPEED_FAST, /* 400 kHz */
-	STM32F4_I2C_SPEED_END,
-};
-
 /**
  * struct stm32f4_i2c_msg - client specific data
  * @addr: 8-bit slave addr, including r/w bit
@@ -159,7 +155,7 @@ static int stm32f4_i2c_set_periph_clk_freq(struct stm32f4_i2c_dev *i2c_dev)
 	i2c_dev->parent_rate = clk_get_rate(i2c_dev->clk);
 	freq = DIV_ROUND_UP(i2c_dev->parent_rate, HZ_TO_MHZ);
 
-	if (i2c_dev->speed == STM32F4_I2C_SPEED_STANDARD) {
+	if (i2c_dev->speed == STM32_I2C_SPEED_STANDARD) {
 		/*
 		 * To reach 100 kHz, the parent clk frequency should be between
 		 * a minimum value of 2 MHz and a maximum value of 46 MHz due
@@ -216,7 +212,7 @@ static void stm32f4_i2c_set_rise_time(struct stm32f4_i2c_dev *i2c_dev)
 	 * is not higher than 46 MHz . As a result trise is at most 4 bits wide
 	 * and so fits into the TRISE bits [5:0].
 	 */
-	if (i2c_dev->speed == STM32F4_I2C_SPEED_STANDARD)
+	if (i2c_dev->speed == STM32_I2C_SPEED_STANDARD)
 		trise = freq + 1;
 	else
 		trise = freq * 3 / 10 + 1;
@@ -230,7 +226,7 @@ static void stm32f4_i2c_set_speed_mode(struct stm32f4_i2c_dev *i2c_dev)
 	u32 val;
 	u32 ccr = 0;
 
-	if (i2c_dev->speed == STM32F4_I2C_SPEED_STANDARD) {
+	if (i2c_dev->speed == STM32_I2C_SPEED_STANDARD) {
 		/*
 		 * In standard mode:
 		 * t_scl_high = t_scl_low = CCR * I2C parent clk period
@@ -808,10 +804,10 @@ static int stm32f4_i2c_probe(struct platform_device *pdev)
 	udelay(2);
 	reset_control_deassert(rst);
 
-	i2c_dev->speed = STM32F4_I2C_SPEED_STANDARD;
+	i2c_dev->speed = STM32_I2C_SPEED_STANDARD;
 	ret = of_property_read_u32(np, "clock-frequency", &clk_rate);
 	if (!ret && clk_rate >= 400000)
-		i2c_dev->speed = STM32F4_I2C_SPEED_FAST;
+		i2c_dev->speed = STM32_I2C_SPEED_FAST;
 
 	i2c_dev->dev = &pdev->dev;