Merge tag 'reset-for-4.3' of git://git.pengutronix.de/git/pza/linux into next/drivers

Reset controller changes for v4.3

- moved the DT reset binding includes from
  include/dt-bindings/reset-controller to include/dt-bindings/reset
- new driver for LPC18xx Reset Generation Unit (RGU)
- of_device_id array in the STi driver changed to const.
- extend SoCFPGA reset driver to support Arria10
- new ath79 reset controller driver for AR71XX/AR9XXX
- new driver for Xilinx Zynq reset controller

* tag 'reset-for-4.3' of git://git.pengutronix.de/git/pza/linux:
  reset: reset-zynq: Adding support for Xilinx Zynq reset controller.
  docs: dts: Added documentation for Xilinx Zynq Reset Controller bindings.
  MIPS: ath79: Add the reset controller to the AR9132 dtsi
  reset: Add a driver for the reset controller on the AR71XX/AR9XXX
  devicetree: Add bindings for the ATH79 reset controller
  reset: socfpga: Update reset-socfpga to read the altr,modrst-offset property
  doc: dt: add documentation for lpc1850-rgu reset driver
  reset: add driver for lpc18xx rgu
  reset: sti: constify of_device_id array
  ARM: STi: DT: Move reset controller constants into common location
  MAINTAINERS: add include/dt-bindings/reset path to reset controller entry
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/reset/ath79-reset.txt

+Binding for Qualcomm Atheros AR7xxx/AR9XXX reset controller
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required Properties:
+- compatible: has to be "qca,<soctype>-reset", "qca,ar7100-reset"
+              as fallback
+- reg: Base address and size of the controllers memory area
+- #reset-cells : Specifies the number of cells needed to encode reset
+                 line, should be 1
+
+Example:
+
+	reset-controller@1806001c {
+		compatible = "qca,ar9132-reset", "qca,ar7100-reset";
+		reg = <0x1806001c 0x4>;
+
+		#reset-cells = <1>;
+	};

Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt

+NXP LPC1850  Reset Generation Unit (RGU)
+========================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "nxp,lpc1850-rgu"
+- reg: register base and length
+- clocks: phandle and clock specifier to RGU clocks
+- clock-names: should contain "delay" and "reg"
+- #reset-cells: should be 1
+
+See table below for valid peripheral reset numbers. Numbers not
+in the table below are either reserved or not applicable for
+normal operation.
+
+Reset	Peripheral
+  9	System control unit (SCU)
+ 12	ARM Cortex-M0 subsystem core (LPC43xx only)
+ 13	CPU core
+ 16	LCD controller
+ 17	USB0
+ 18	USB1
+ 19	DMA
+ 20	SDIO
+ 21	External memory controller (EMC)
+ 22	Ethernet
+ 25	Flash bank A
+ 27	EEPROM
+ 28	GPIO
+ 29	Flash bank B
+ 32	Timer0
+ 33	Timer1
+ 34	Timer2
+ 35	Timer3
+ 36	Repetitive Interrupt timer (RIT)
+ 37	State Configurable Timer (SCT)
+ 38	Motor control PWM (MCPWM)
+ 39	QEI
+ 40	ADC0
+ 41	ADC1
+ 42	DAC
+ 44	USART0
+ 45	UART1
+ 46	USART2
+ 47	USART3
+ 48	I2C0
+ 49	I2C1
+ 50	SSP0
+ 51	SSP1
+ 52	I2S0 and I2S1
+ 53	Serial Flash Interface (SPIFI)
+ 54	C_CAN1
+ 55	C_CAN0
+ 56	ARM Cortex-M0 application core (LPC4370 only)
+ 57	SGPIO (LPC43xx only)
+ 58	SPI (LPC43xx only)
+ 60	ADCHS (12-bit ADC) (LPC4370 only)
+
+Refer to NXP LPC18xx or LPC43xx user manual for more details about
+the reset signals and the connected block/peripheral.
+
+Reset provider example:
+rgu: reset-controller@40053000 {
+	compatible = "nxp,lpc1850-rgu";
+	reg = <0x40053000 0x1000>;
+	clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>;
+	clock-names = "delay", "reg";
+	#reset-cells = <1>;
+};
+
+Reset consumer example:
+mac: ethernet@40010000 {
+	compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
+	reg = <0x40010000 0x2000>;
+	interrupts = <5>;
+	interrupt-names = "macirq";
+	clocks = <&ccu1 CLK_CPU_ETHERNET>;
+	clock-names = "stmmaceth";
+	resets = <&rgu 22>;
+	reset-names = "stmmaceth";
+	status = "disabled";
+};

Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt

@@ -39,4 +39,4 @@ Example:
 	};
 
 Macro definitions for the supported reset channels can be found in:
-include/dt-bindings/reset-controller/stih407-resets.h
+include/dt-bindings/reset/stih407-resets.h

Documentation/devicetree/bindings/reset/st,sti-powerdown.txt

@@ -43,5 +43,5 @@ example:
 
 Macro definitions for the supported reset channels can be found in:
 
-include/dt-bindings/reset-controller/stih415-resets.h
-include/dt-bindings/reset-controller/stih416-resets.h
+include/dt-bindings/reset/stih415-resets.h
+include/dt-bindings/reset/stih416-resets.h

Documentation/devicetree/bindings/reset/st,sti-softreset.txt

@@ -42,5 +42,5 @@ example:
 
 Macro definitions for the supported reset channels can be found in:
 
-include/dt-bindings/reset-controller/stih415-resets.h
-include/dt-bindings/reset-controller/stih416-resets.h
+include/dt-bindings/reset/stih415-resets.h
+include/dt-bindings/reset/stih416-resets.h

Documentation/devicetree/bindings/reset/zynq-reset.txt

+Xilinx Zynq Reset Manager
+
+The Zynq AP-SoC has several different resets.
+
+See Chapter 26 of the Zynq TRM (UG585) for more information about Zynq resets.
+
+Required properties:
+- compatible: "xlnx,zynq-reset"
+- reg: SLCR offset and size taken via syscon <0x200 0x48>
+- syscon: <&slcr>
+  This should be a phandle to the Zynq's SLCR registers.
+- #reset-cells: Must be 1
+
+The Zynq Reset Manager needs to be a childnode of the SLCR.
+
+Example:
+	rstc: rstc@200 {
+		compatible = "xlnx,zynq-reset";
+		reg = <0x200 0x48>;
+		#reset-cells = <1>;
+		syscon = <&slcr>;
+	};
+
+Reset outputs:
+ 0  : soft reset
+ 32 : ddr reset
+ 64 : topsw reset
+ 96 : dmac reset
+ 128: usb0 reset
+ 129: usb1 reset
+ 160: gem0 reset
+ 161: gem1 reset
+ 164: gem0 rx reset
+ 165: gem1 rx reset
+ 166: gem0 ref reset
+ 167: gem1 ref reset
+ 192: sdio0 reset
+ 193: sdio1 reset
+ 196: sdio0 ref reset
+ 197: sdio1 ref reset
+ 224: spi0 reset
+ 225: spi1 reset
+ 226: spi0 ref reset
+ 227: spi1 ref reset
+ 256: can0 reset
+ 257: can1 reset
+ 258: can0 ref reset
+ 259: can1 ref reset
+ 288: i2c0 reset
+ 289: i2c1 reset
+ 320: uart0 reset
+ 321: uart1 reset
+ 322: uart0 ref reset
+ 323: uart1 ref reset
+ 352: gpio reset
+ 384: lqspi reset
+ 385: qspi ref reset
+ 416: smc reset
+ 417: smc ref reset
+ 448: ocm reset
+ 512: fpga0 out reset
+ 513: fpga1 out reset
+ 514: fpga2 out reset
+ 515: fpga3 out reset
+ 544: a9 reset 0
+ 545: a9 reset 1
+ 552: peri reset
+

MAINTAINERS

@@ -8553,6 +8553,7 @@ M:	Philipp Zabel <p.zabel@pengutronix.de>
 S:	Maintained
 F:	drivers/reset/
 F:	Documentation/devicetree/bindings/reset/
+F:	include/dt-bindings/reset/
 F:	include/linux/reset.h
 F:	include/linux/reset-controller.h
 

arch/arm/boot/dts/stih407-family.dtsi

@@ -9,7 +9,7 @@
 #include "stih407-pinctrl.dtsi"
 #include <dt-bindings/mfd/st-lpc.h>
 #include <dt-bindings/phy/phy.h>
-#include <dt-bindings/reset-controller/stih407-resets.h>
+#include <dt-bindings/reset/stih407-resets.h>
 #include <dt-bindings/interrupt-controller/irq-st.h>
 / {
 	#address-cells = <1>;

arch/arm/boot/dts/stih415.dtsi

@@ -10,7 +10,7 @@
 #include "stih415-clock.dtsi"
 #include "stih415-pinctrl.dtsi"
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/reset-controller/stih415-resets.h>
+#include <dt-bindings/reset/stih415-resets.h>
 / {
 
 	L2: cache-controller {

arch/arm/boot/dts/stih416.dtsi

@@ -12,7 +12,7 @@
 
 #include <dt-bindings/phy/phy.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/reset-controller/stih416-resets.h>
+#include <dt-bindings/reset/stih416-resets.h>
 #include <dt-bindings/interrupt-controller/irq-st.h>
 / {
 	L2: cache-controller {

arch/mips/Kconfig

@@ -118,6 +118,7 @@ config ATH25
 
 config ATH79
 	bool "Atheros AR71XX/AR724X/AR913X based boards"
+	select ARCH_HAS_RESET_CONTROLLER
 	select ARCH_REQUIRE_GPIOLIB
 	select BOOT_RAW
 	select CEVT_R4K

arch/mips/boot/dts/qca/ar9132.dtsi

@@ -115,6 +115,14 @@ miscintc: interrupt-controller@18060010 {
 				interrupt-controller;
 				#interrupt-cells = <1>;
 			};
+
+			rst: reset-controller@1806001c {
+				compatible = "qca,ar9132-reset",
+						"qca,ar7100-reset";
+				reg = <0x1806001c 0x4>;
+
+				#reset-cells = <1>;
+			};
 		};
 
 		spi@1f000000 {

drivers/reset/Makefile

 obj-$(CONFIG_RESET_CONTROLLER) += core.o
+obj-$(CONFIG_ARCH_LPC18XX) += reset-lpc18xx.o
 obj-$(CONFIG_ARCH_SOCFPGA) += reset-socfpga.o
 obj-$(CONFIG_ARCH_BERLIN) += reset-berlin.o
 obj-$(CONFIG_ARCH_SUNXI) += reset-sunxi.o
 obj-$(CONFIG_ARCH_STI) += sti/
+obj-$(CONFIG_ARCH_ZYNQ) += reset-zynq.o
+obj-$(CONFIG_ATH79) += reset-ath79.o

drivers/reset/reset-ath79.c

+/*
+ * Copyright (C) 2015 Alban Bedel <albeu@free.fr>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+
+struct ath79_reset {
+	struct reset_controller_dev rcdev;
+	void __iomem *base;
+	spinlock_t lock;
+};
+
+static int ath79_reset_update(struct reset_controller_dev *rcdev,
+			unsigned long id, bool assert)
+{
+	struct ath79_reset *ath79_reset =
+		container_of(rcdev, struct ath79_reset, rcdev);
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(&ath79_reset->lock, flags);
+	val = readl(ath79_reset->base);
+	if (assert)
+		val |= BIT(id);
+	else
+		val &= ~BIT(id);
+	writel(val, ath79_reset->base);
+	spin_unlock_irqrestore(&ath79_reset->lock, flags);
+
+	return 0;
+}
+
+static int ath79_reset_assert(struct reset_controller_dev *rcdev,
+			unsigned long id)
+{
+	return ath79_reset_update(rcdev, id, true);
+}
+
+static int ath79_reset_deassert(struct reset_controller_dev *rcdev,
+				unsigned long id)
+{
+	return ath79_reset_update(rcdev, id, false);
+}
+
+static int ath79_reset_status(struct reset_controller_dev *rcdev,
+			unsigned long id)
+{
+	struct ath79_reset *ath79_reset =
+		container_of(rcdev, struct ath79_reset, rcdev);
+	u32 val;
+
+	val = readl(ath79_reset->base);
+
+	return !!(val & BIT(id));
+}
+
+static struct reset_control_ops ath79_reset_ops = {
+	.assert = ath79_reset_assert,
+	.deassert = ath79_reset_deassert,
+	.status = ath79_reset_status,
+};
+
+static int ath79_reset_probe(struct platform_device *pdev)
+{
+	struct ath79_reset *ath79_reset;
+	struct resource *res;
+
+	ath79_reset = devm_kzalloc(&pdev->dev,
+				sizeof(*ath79_reset), GFP_KERNEL);
+	if (!ath79_reset)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, ath79_reset);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ath79_reset->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ath79_reset->base))
+		return PTR_ERR(ath79_reset->base);
+
+	ath79_reset->rcdev.ops = &ath79_reset_ops;
+	ath79_reset->rcdev.owner = THIS_MODULE;
+	ath79_reset->rcdev.of_node = pdev->dev.of_node;
+	ath79_reset->rcdev.of_reset_n_cells = 1;
+	ath79_reset->rcdev.nr_resets = 32;
+
+	return reset_controller_register(&ath79_reset->rcdev);
+}
+
+static int ath79_reset_remove(struct platform_device *pdev)
+{
+	struct ath79_reset *ath79_reset = platform_get_drvdata(pdev);
+
+	reset_controller_unregister(&ath79_reset->rcdev);
+
+	return 0;
+}
+
+static const struct of_device_id ath79_reset_dt_ids[] = {
+	{ .compatible = "qca,ar7100-reset", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ath79_reset_dt_ids);
+
+static struct platform_driver ath79_reset_driver = {
+	.probe	= ath79_reset_probe,
+	.remove = ath79_reset_remove,
+	.driver = {
+		.name		= "ath79-reset",
+		.of_match_table	= ath79_reset_dt_ids,
+	},
+};
+module_platform_driver(ath79_reset_driver);
+
+MODULE_AUTHOR("Alban Bedel <albeu@free.fr>");
+MODULE_DESCRIPTION("AR71xx Reset Controller Driver");
+MODULE_LICENSE("GPL");

drivers/reset/reset-lpc18xx.c

+/*
+ * Reset driver for NXP LPC18xx/43xx Reset Generation Unit (RGU).
+ *
+ * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reboot.h>
+#include <linux/reset-controller.h>
+#include <linux/spinlock.h>
+
+/* LPC18xx RGU registers */
+#define LPC18XX_RGU_CTRL0		0x100
+#define LPC18XX_RGU_CTRL1		0x104
+#define LPC18XX_RGU_ACTIVE_STATUS0	0x150
+#define LPC18XX_RGU_ACTIVE_STATUS1	0x154
+
+#define LPC18XX_RGU_RESETS_PER_REG	32
+
+/* Internal reset outputs */
+#define LPC18XX_RGU_CORE_RST	0
+#define LPC43XX_RGU_M0SUB_RST	12
+#define LPC43XX_RGU_M0APP_RST	56
+
+struct lpc18xx_rgu_data {
+	struct reset_controller_dev rcdev;
+	struct clk *clk_delay;
+	struct clk *clk_reg;
+	void __iomem *base;
+	spinlock_t lock;
+	u32 delay_us;
+};
+
+#define to_rgu_data(p) container_of(p, struct lpc18xx_rgu_data, rcdev)
+
+static void __iomem *rgu_base;
+
+static int lpc18xx_rgu_restart(struct notifier_block *this, unsigned long mode,
+			       void *cmd)
+{
+	writel(BIT(LPC18XX_RGU_CORE_RST), rgu_base + LPC18XX_RGU_CTRL0);
+	mdelay(2000);
+
+	pr_emerg("%s: unable to restart system\n", __func__);
+
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block lpc18xx_rgu_restart_nb = {
+	.notifier_call = lpc18xx_rgu_restart,
+	.priority = 192,
+};
+
+/*
+ * The LPC18xx RGU has mostly self-deasserting resets except for the
+ * two reset lines going to the internal Cortex-M0 cores.
+ *
+ * To prevent the M0 core resets from accidentally getting deasserted
+ * status register must be check and bits in control register set to
+ * preserve the state.
+ */
+static int lpc18xx_rgu_setclear_reset(struct reset_controller_dev *rcdev,
+				      unsigned long id, bool set)
+{
+	struct lpc18xx_rgu_data *rc = to_rgu_data(rcdev);
+	u32 stat_offset = LPC18XX_RGU_ACTIVE_STATUS0;
+	u32 ctrl_offset = LPC18XX_RGU_CTRL0;
+	unsigned long flags;
+	u32 stat, rst_bit;
+
+	stat_offset += (id / LPC18XX_RGU_RESETS_PER_REG) * sizeof(u32);
+	ctrl_offset += (id / LPC18XX_RGU_RESETS_PER_REG) * sizeof(u32);
+	rst_bit = 1 << (id % LPC18XX_RGU_RESETS_PER_REG);
+
+	spin_lock_irqsave(&rc->lock, flags);
+	stat = ~readl(rc->base + stat_offset);
+	if (set)
+		writel(stat | rst_bit, rc->base + ctrl_offset);
+	else
+		writel(stat & ~rst_bit, rc->base + ctrl_offset);
+	spin_unlock_irqrestore(&rc->lock, flags);
+
+	return 0;
+}
+
+static int lpc18xx_rgu_assert(struct reset_controller_dev *rcdev,
+			      unsigned long id)
+{
+	return lpc18xx_rgu_setclear_reset(rcdev, id, true);
+}
+
+static int lpc18xx_rgu_deassert(struct reset_controller_dev *rcdev,
+				unsigned long id)
+{
+	return lpc18xx_rgu_setclear_reset(rcdev, id, false);
+}
+
+/* Only M0 cores require explicit reset deassert */
+static int lpc18xx_rgu_reset(struct reset_controller_dev *rcdev,
+			     unsigned long id)
+{
+	struct lpc18xx_rgu_data *rc = to_rgu_data(rcdev);
+
+	lpc18xx_rgu_assert(rcdev, id);
+	udelay(rc->delay_us);
+
+	switch (id) {
+	case LPC43XX_RGU_M0SUB_RST:
+	case LPC43XX_RGU_M0APP_RST:
+		lpc18xx_rgu_setclear_reset(rcdev, id, false);
+	}
+
+	return 0;
+}
+
+static int lpc18xx_rgu_status(struct reset_controller_dev *rcdev,
+			      unsigned long id)
+{
+	struct lpc18xx_rgu_data *rc = to_rgu_data(rcdev);
+	u32 bit, offset = LPC18XX_RGU_ACTIVE_STATUS0;
+
+	offset += (id / LPC18XX_RGU_RESETS_PER_REG) * sizeof(u32);
+	bit = 1 << (id % LPC18XX_RGU_RESETS_PER_REG);
+
+	return !(readl(rc->base + offset) & bit);
+}
+
+static struct reset_control_ops lpc18xx_rgu_ops = {
+	.reset		= lpc18xx_rgu_reset,
+	.assert		= lpc18xx_rgu_assert,
+	.deassert	= lpc18xx_rgu_deassert,
+	.status		= lpc18xx_rgu_status,
+};
+
+static int lpc18xx_rgu_probe(struct platform_device *pdev)
+{
+	struct lpc18xx_rgu_data *rc;
+	struct resource *res;
+	u32 fcclk, firc;
+	int ret;
+
+	rc = devm_kzalloc(&pdev->dev, sizeof(*rc), GFP_KERNEL);
+	if (!rc)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	rc->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(rc->base))
+		return PTR_ERR(rc->base);
+
+	rc->clk_reg = devm_clk_get(&pdev->dev, "reg");
+	if (IS_ERR(rc->clk_reg)) {
+		dev_err(&pdev->dev, "reg clock not found\n");
+		return PTR_ERR(rc->clk_reg);
+	}
+
+	rc->clk_delay = devm_clk_get(&pdev->dev, "delay");
+	if (IS_ERR(rc->clk_delay)) {
+		dev_err(&pdev->dev, "delay clock not found\n");
+		return PTR_ERR(rc->clk_delay);
+	}
+
+	ret = clk_prepare_enable(rc->clk_reg);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to enable reg clock\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(rc->clk_delay);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to enable delay clock\n");
+		goto dis_clk_reg;
+	}
+
+	fcclk = clk_get_rate(rc->clk_reg) / USEC_PER_SEC;
+	firc = clk_get_rate(rc->clk_delay) / USEC_PER_SEC;
+	if (fcclk == 0 || firc == 0)
+		rc->delay_us = 2;
+	else
+		rc->delay_us = DIV_ROUND_UP(fcclk, firc * firc);
+
+	spin_lock_init(&rc->lock);
+
+	rc->rcdev.owner = THIS_MODULE;
+	rc->rcdev.nr_resets = 64;
+	rc->rcdev.ops = &lpc18xx_rgu_ops;
+	rc->rcdev.of_node = pdev->dev.of_node;
+
+	platform_set_drvdata(pdev, rc);
+
+	ret = reset_controller_register(&rc->rcdev);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to register device\n");
+		goto dis_clks;
+	}
+
+	rgu_base = rc->base;
+	ret = register_restart_handler(&lpc18xx_rgu_restart_nb);
+	if (ret)
+		dev_warn(&pdev->dev, "failed to register restart handler\n");
+
+	return 0;
+
+dis_clks:
+	clk_disable_unprepare(rc->clk_delay);
+dis_clk_reg:
+	clk_disable_unprepare(rc->clk_reg);
+
+	return ret;
+}
+
+static int lpc18xx_rgu_remove(struct platform_device *pdev)
+{
+	struct lpc18xx_rgu_data *rc = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = unregister_restart_handler(&lpc18xx_rgu_restart_nb);
+	if (ret)
+		dev_warn(&pdev->dev, "failed to unregister restart handler\n");
+
+	reset_controller_unregister(&rc->rcdev);
+
+	clk_disable_unprepare(rc->clk_delay);
+	clk_disable_unprepare(rc->clk_reg);
+
+	return 0;
+}
+
+static const struct of_device_id lpc18xx_rgu_match[] = {
+	{ .compatible = "nxp,lpc1850-rgu" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, lpc18xx_rgu_match);
+
+static struct platform_driver lpc18xx_rgu_driver = {
+	.probe	= lpc18xx_rgu_probe,
+	.remove	= lpc18xx_rgu_remove,
+	.driver	= {
+		.name		= "lpc18xx-reset",
+		.of_match_table	= lpc18xx_rgu_match,
+	},
+};
+module_platform_driver(lpc18xx_rgu_driver);
+
+MODULE_AUTHOR("Joachim Eastwood <manabian@gmail.com>");
+MODULE_DESCRIPTION("Reset driver for LPC18xx/43xx RGU");
+MODULE_LICENSE("GPL v2");

drivers/reset/reset-socfpga.c

@@ -24,11 +24,11 @@
 #include <linux/types.h>
 
 #define NR_BANKS		4
-#define OFFSET_MODRST		0x10
 
 struct socfpga_reset_data {
 	spinlock_t			lock;
 	void __iomem			*membase;
+	u32				modrst_offset;
 	struct reset_controller_dev	rcdev;
 };
 
@@ -45,8 +45,8 @@ static int socfpga_reset_assert(struct reset_controller_dev *rcdev,
 
 	spin_lock_irqsave(&data->lock, flags);
 
-	reg = readl(data->membase + OFFSET_MODRST + (bank * NR_BANKS));
-	writel(reg | BIT(offset), data->membase + OFFSET_MODRST +
+	reg = readl(data->membase + data->modrst_offset + (bank * NR_BANKS));
+	writel(reg | BIT(offset), data->membase + data->modrst_offset +
 				 (bank * NR_BANKS));
 	spin_unlock_irqrestore(&data->lock, flags);
 
@@ -67,8 +67,8 @@ static int socfpga_reset_deassert(struct reset_controller_dev *rcdev,
 
 	spin_lock_irqsave(&data->lock, flags);
 
-	reg = readl(data->membase + OFFSET_MODRST + (bank * NR_BANKS));
-	writel(reg & ~BIT(offset), data->membase + OFFSET_MODRST +
+	reg = readl(data->membase + data->modrst_offset + (bank * NR_BANKS));
+	writel(reg & ~BIT(offset), data->membase + data->modrst_offset +
 				  (bank * NR_BANKS));
 
 	spin_unlock_irqrestore(&data->lock, flags);
@@ -85,7 +85,7 @@ static int socfpga_reset_status(struct reset_controller_dev *rcdev,
 	int offset = id % BITS_PER_LONG;
 	u32 reg;
 
-	reg = readl(data->membase + OFFSET_MODRST + (bank * NR_BANKS));
+	reg = readl(data->membase + data->modrst_offset + (bank * NR_BANKS));
 
 	return !(reg & BIT(offset));
 }
@@ -100,6 +100,8 @@ static int socfpga_reset_probe(struct platform_device *pdev)
 {
 	struct socfpga_reset_data *data;
 	struct resource *res;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
 
 	/*
 	 * The binding was mainlined without the required property.
@@ -120,6 +122,11 @@ static int socfpga_reset_probe(struct platform_device *pdev)
 	if (IS_ERR(data->membase))
 		return PTR_ERR(data->membase);
 
+	if (of_property_read_u32(np, "altr,modrst-offset", &data->modrst_offset)) {
+		dev_warn(dev, "missing altr,modrst-offset property, assuming 0x10!\n");
+		data->modrst_offset = 0x10;
+	}
+
 	spin_lock_init(&data->lock);
 
 	data->rcdev.owner = THIS_MODULE;

drivers/reset/reset-zynq.c

+/*
+ * Copyright (c) 2015, National Instruments Corp.
+ *
+ * Xilinx Zynq Reset controller driver
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+struct zynq_reset_data {
+	struct regmap *slcr;
+	struct reset_controller_dev rcdev;
+	u32 offset;
+};
+
+#define to_zynq_reset_data(p)		\
+	container_of((p), struct zynq_reset_data, rcdev)
+
+static int zynq_reset_assert(struct reset_controller_dev *rcdev,
+			     unsigned long id)
+{
+	struct zynq_reset_data *priv = to_zynq_reset_data(rcdev);
+
+	int bank = id / BITS_PER_LONG;
+	int offset = id % BITS_PER_LONG;
+
+	pr_debug("%s: %s reset bank %u offset %u\n", KBUILD_MODNAME, __func__,
+		 bank, offset);
+
+	return regmap_update_bits(priv->slcr,
+				  priv->offset + (bank * 4),
+				  BIT(offset),
+				  BIT(offset));
+}
+
+static int zynq_reset_deassert(struct reset_controller_dev *rcdev,
+			       unsigned long id)
+{
+	struct zynq_reset_data *priv = to_zynq_reset_data(rcdev);
+
+	int bank = id / BITS_PER_LONG;
+	int offset = id % BITS_PER_LONG;
+
+	pr_debug("%s: %s reset bank %u offset %u\n", KBUILD_MODNAME, __func__,
+		 bank, offset);
+
+	return regmap_update_bits(priv->slcr,
+				  priv->offset + (bank * 4),
+				  BIT(offset),
+				  ~BIT(offset));
+}
+
+static int zynq_reset_status(struct reset_controller_dev *rcdev,
+			     unsigned long id)
+{
+	struct zynq_reset_data *priv = to_zynq_reset_data(rcdev);
+
+	int bank = id / BITS_PER_LONG;
+	int offset = id % BITS_PER_LONG;
+	int ret;
+	u32 reg;
+
+	pr_debug("%s: %s reset bank %u offset %u\n", KBUILD_MODNAME, __func__,
+		 bank, offset);
+
+	ret = regmap_read(priv->slcr, priv->offset + (bank * 4), &reg);
+	if (ret)
+		return ret;
+
+	return !!(reg & BIT(offset));
+}
+
+static struct reset_control_ops zynq_reset_ops = {
+	.assert		= zynq_reset_assert,
+	.deassert	= zynq_reset_deassert,
+	.status		= zynq_reset_status,
+};
+
+static int zynq_reset_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct zynq_reset_data *priv;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, priv);
+
+	priv->slcr = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+						     "syscon");
+	if (IS_ERR(priv->slcr)) {
+		dev_err(&pdev->dev, "unable to get zynq-slcr regmap");
+		return PTR_ERR(priv->slcr);
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "missing IO resource\n");
+		return -ENODEV;
+	}
+
+	priv->offset = res->start;
+
+	priv->rcdev.owner = THIS_MODULE;
+	priv->rcdev.nr_resets = resource_size(res) / 4 * BITS_PER_LONG;
+	priv->rcdev.ops = &zynq_reset_ops;
+	priv->rcdev.of_node = pdev->dev.of_node;
+	reset_controller_register(&priv->rcdev);
+
+	return 0;
+}
+
+static int zynq_reset_remove(struct platform_device *pdev)
+{
+	struct zynq_reset_data *priv = platform_get_drvdata(pdev);
+
+	reset_controller_unregister(&priv->rcdev);
+
+	return 0;
+}
+
+static const struct of_device_id zynq_reset_dt_ids[] = {
+	{ .compatible = "xlnx,zynq-reset", },
+	{ /* sentinel */ },
+};
+
+static struct platform_driver zynq_reset_driver = {
+	.probe	= zynq_reset_probe,
+	.remove	= zynq_reset_remove,
+	.driver = {
+		.name		= KBUILD_MODNAME,
+		.of_match_table	= zynq_reset_dt_ids,
+	},
+};
+module_platform_driver(zynq_reset_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Moritz Fischer <moritz.fischer@ettus.com>");
+MODULE_DESCRIPTION("Zynq Reset Controller Driver");

drivers/reset/sti/reset-stih407.c

@@ -11,7 +11,7 @@
 #include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
-#include <dt-bindings/reset-controller/stih407-resets.h>
+#include <dt-bindings/reset/stih407-resets.h>
 #include "reset-syscfg.h"
 
 /* STiH407 Peripheral powerdown definitions. */
@@ -126,7 +126,7 @@ static const struct syscfg_reset_controller_data stih407_picophyreset_controller
 	.channels = stih407_picophyresets,
 };
 
-static struct of_device_id stih407_reset_match[] = {
+static const struct of_device_id stih407_reset_match[] = {
 	{
 		.compatible = "st,stih407-powerdown",
 		.data = &stih407_powerdown_controller,

drivers/reset/sti/reset-stih415.c

@@ -13,7 +13,7 @@
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 
-#include <dt-bindings/reset-controller/stih415-resets.h>
+#include <dt-bindings/reset/stih415-resets.h>
 
 #include "reset-syscfg.h"
 
@@ -89,7 +89,7 @@ static struct syscfg_reset_controller_data stih415_softreset_controller = {
 	.channels = stih415_softresets,
 };
 
-static struct of_device_id stih415_reset_match[] = {
+static const struct of_device_id stih415_reset_match[] = {
 	{ .compatible = "st,stih415-powerdown",
 	  .data = &stih415_powerdown_controller, },
 	{ .compatible = "st,stih415-softreset",

drivers/reset/sti/reset-stih416.c

@@ -13,7 +13,7 @@
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 
-#include <dt-bindings/reset-controller/stih416-resets.h>
+#include <dt-bindings/reset/stih416-resets.h>
 
 #include "reset-syscfg.h"
 
@@ -120,7 +120,7 @@ static struct syscfg_reset_controller_data stih416_softreset_controller = {
 	.channels = stih416_softresets,
 };
 
-static struct of_device_id stih416_reset_match[] = {
+static const struct of_device_id stih416_reset_match[] = {
 	{ .compatible = "st,stih416-powerdown",
 	  .data = &stih416_powerdown_controller, },
 	{ .compatible = "st,stih416-softreset",