Commit bdacbce6 authored by Russ Dill's avatar Russ Dill Committed by Tony Lindgren

ARM: OMAP2+: smsc911x: Remove regulator support from gmpc-smsc911x

Adding in support for regulators here creates several headaches.
 - Boards that declare their own regulator cannot use this function.
 - Multiple calls to this function require special handling.
 - Boards that declare id's other than '0' need special handling.

Now that there is a simple regulator_register_fixed, we can push
this registration back into the board files.
Signed-off-by: default avatarRuss Dill <russ.dill@ti.com>
Tested-by: default avatarIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent a297068c
......@@ -19,8 +19,6 @@
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/smsc911x.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <plat/board.h>
#include <plat/gpmc.h>
......@@ -41,50 +39,6 @@ static struct smsc911x_platform_config gpmc_smsc911x_config = {
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
};
static struct regulator_consumer_supply gpmc_smsc911x_supply[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
};
/* Generic regulator definition to satisfy smsc911x */
static struct regulator_init_data gpmc_smsc911x_reg_init_data = {
.constraints = {
.min_uV = 3300000,
.max_uV = 3300000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(gpmc_smsc911x_supply),
.consumer_supplies = gpmc_smsc911x_supply,
};
static struct fixed_voltage_config gpmc_smsc911x_fixed_reg_data = {
.supply_name = "gpmc_smsc911x",
.microvolts = 3300000,
.gpio = -EINVAL,
.startup_delay = 0,
.enable_high = 0,
.enabled_at_boot = 1,
.init_data = &gpmc_smsc911x_reg_init_data,
};
/*
* Platform device id of 42 is a temporary fix to avoid conflicts
* with other reg-fixed-voltage devices. The real fix should
* involve the driver core providing a way of dynamically
* assigning a unique id on registration for platform devices
* in the same name space.
*/
static struct platform_device gpmc_smsc911x_regulator = {
.name = "reg-fixed-voltage",
.id = 42,
.dev = {
.platform_data = &gpmc_smsc911x_fixed_reg_data,
},
};
/*
* Initialize smsc911x device connected to the GPMC. Note that we
* assume that pin multiplexing is done in the board-*.c file,
......@@ -96,15 +50,6 @@ void __init gpmc_smsc911x_init(struct omap_smsc911x_platform_data *gpmc_cfg)
unsigned long cs_mem_base;
int ret;
if (!gpmc_cfg->id) {
ret = platform_device_register(&gpmc_smsc911x_regulator);
if (ret < 0) {
pr_err("Unable to register smsc911x regulators: %d\n",
ret);
return;
}
}
if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) {
pr_err("Failed to request GPMC mem region\n");
return;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment