ARM: dts: i.MX51 boards: Switch to use standard GPIO flags definitions

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

arch/arm/boot/dts/imx51-apf51.dts

@@ -36,7 +36,7 @@ &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec>;
 	phy-mode = "mii";
-	phy-reset-gpios = <&gpio3 0 0>;
+	phy-reset-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
 	phy-reset-duration = <1>;
 	status = "okay";
 };

arch/arm/boot/dts/imx51-apf51dev.dts

@@ -48,7 +48,7 @@ gpio-keys {
 
 		user-key {
 			label = "user";
-			gpios = <&gpio1 3 0>;
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
 			linux,code = <256>; /* BTN_0 */
 		};
 	};
@@ -58,7 +58,7 @@ leds {
 
 		user {
 			label = "Heartbeat";
-			gpios = <&gpio1 2 0>;
+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
@@ -68,7 +68,8 @@ &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	fsl,spi-num-chipselects = <2>;
-	cs-gpios = <&gpio4 24 0>, <&gpio4 25 0>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>,
+		   <&gpio4 25 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
@@ -76,14 +77,15 @@ &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	fsl,spi-num-chipselects = <2>;
-	cs-gpios = <&gpio3 28 1>, <&gpio3 27 1>;
+	cs-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>,
+		   <&gpio3 27 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio2 29 0>;
+	cd-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
 	bus-width = <4>;
 	status = "okay";
 };

arch/arm/boot/dts/imx51-babbage.dts

@@ -75,7 +75,7 @@ gpio-keys {
 
 		power {
 			label = "Power Button";
-			gpios = <&gpio2 21 0>;
+			gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
 			linux,code = <116>; /* KEY_POWER */
 			gpio-key,wakeup;
 		};
@@ -105,7 +105,7 @@ clk_26M: codec_clock {
 			reg=<0>;
 			#clock-cells = <0>;
 			clock-frequency = <26000000>;
-			gpios = <&gpio4 26 1>;
+			gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -121,8 +121,8 @@ &esdhc1 {
 &esdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc2>;
-	cd-gpios = <&gpio1 6 0>;
-	wp-gpios = <&gpio1 5 0>;
+	cd-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+	wp-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
@@ -137,7 +137,8 @@ &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	fsl,spi-num-chipselects = <2>;
-	cs-gpios = <&gpio4 24 0>, <&gpio4 25 0>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>,
+		   <&gpio4 25 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
 	pmic: mc13892@0 {

arch/arm/boot/dts/imx51.dtsi

@@ -14,6 +14,7 @@
 #include "imx51-pinfunc.h"
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/imx5-clock.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	aliases {