Commit bf4861cf authored by Peter Ma's avatar Peter Ma Committed by Haavard Skinnemoen

avr32: add RTS/CTS/CLK pin selection for the USARTs

Adds extra parameter to AT32 at32_map_usart(), so as to reserve
RTS/CTS/CLK pins.

All boards under arch/avr32/boards have been updated (trivial change), but
not all have been tested.
Signed-off-by: default avatarPeter Ma <pma@mediamatech.com>
Signed-off-by: default avatarHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
parent a6b6b5ff
......@@ -118,7 +118,7 @@ static void __init set_hw_addr(struct platform_device *pdev)
void __init setup_board(void)
{
at32_map_usart(1, 0); /* USART 1: /dev/ttyS0, DB9 */
at32_map_usart(1, 0, 0); /* USART 1: /dev/ttyS0, DB9 */
at32_setup_serial_console(0);
}
......
......@@ -252,12 +252,12 @@ static void __init atstk1002_setup_extdac(void)
void __init setup_board(void)
{
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */
at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */
#else
at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */
at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */
#endif
/* USART 2/unused: expansion connector */
at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */
at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */
at32_setup_serial_console(0);
}
......
......@@ -115,12 +115,12 @@ static void __init atstk1003_setup_extdac(void)
void __init setup_board(void)
{
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */
at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */
#else
at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */
at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */
#endif
/* USART 2/unused: expansion connector */
at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */
at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */
at32_setup_serial_console(0);
}
......
......@@ -120,12 +120,12 @@ static void __init atstk1004_setup_extdac(void)
void __init setup_board(void)
{
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */
at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */
#else
at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */
at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */
#endif
/* USART 2/unused: expansion connector */
at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */
at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */
at32_setup_serial_console(0);
}
......
......@@ -250,7 +250,7 @@ static void __init favr32_setup_atmel_pwm_bl(void)
void __init setup_board(void)
{
at32_map_usart(3, 0); /* USART 3 => /dev/ttyS0 */
at32_map_usart(3, 0, 0); /* USART 3 => /dev/ttyS0 */
at32_setup_serial_console(0);
}
......
......@@ -165,7 +165,7 @@ static void __init set_hw_addr(struct platform_device *pdev)
void __init setup_board(void)
{
at32_map_usart(1, 0); /* USART 1: /dev/ttyS0, DB9 */
at32_map_usart(1, 0, 0); /* USART 1: /dev/ttyS0, DB9 */
at32_setup_serial_console(0);
}
......
......@@ -231,9 +231,9 @@ static void detect_merisc_board_id(void)
void __init setup_board(void)
{
at32_map_usart(0, 0);
at32_map_usart(1, 1);
at32_map_usart(3, 3);
at32_map_usart(0, 0, 0);
at32_map_usart(1, 1, 0);
at32_map_usart(3, 3, 0);
at32_setup_serial_console(1);
}
......@@ -248,7 +248,7 @@ static int __init merisc_init(void)
at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL | (1 << 26));
if (merisc_board_id >= 1)
at32_map_usart(2, 2);
at32_map_usart(2, 2, 0);
at32_add_device_usart(0);
at32_add_device_usart(1);
......
......@@ -175,10 +175,10 @@ static void __init set_hw_addr(struct platform_device *pdev)
void __init setup_board(void)
{
at32_map_usart(0, 0); /* USART 0: /dev/ttyS0 (TTL --> Altera) */
at32_map_usart(1, 1); /* USART 1: /dev/ttyS1 (RS232) */
at32_map_usart(2, 2); /* USART 2: /dev/ttyS2 (RS485) */
at32_map_usart(3, 3); /* USART 3: /dev/ttyS3 (RS422 Multidrop) */
at32_map_usart(0, 0, 0); /* USART 0: /dev/ttyS0 (TTL --> Altera) */
at32_map_usart(1, 1, 0); /* USART 1: /dev/ttyS1 (RS232) */
at32_map_usart(2, 2, 0); /* USART 2: /dev/ttyS2 (RS485) */
at32_map_usart(3, 3, 0); /* USART 3: /dev/ttyS3 (RS422 Multidrop) */
}
static struct i2c_gpio_platform_data i2c_gpio_data = {
......
......@@ -966,56 +966,68 @@ static struct resource atmel_usart3_resource[] = {
DEFINE_DEV_DATA(atmel_usart, 3);
DEV_CLK(usart, atmel_usart3, pba, 6);
static inline void configure_usart0_pins(void)
static inline void configure_usart0_pins(int flags)
{
u32 pin_mask = (1 << 8) | (1 << 9); /* RXD & TXD */
if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 6);
if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 7);
if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 10);
select_peripheral(PIOA, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP);
}
static inline void configure_usart1_pins(void)
static inline void configure_usart1_pins(int flags)
{
u32 pin_mask = (1 << 17) | (1 << 18); /* RXD & TXD */
if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 19);
if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 20);
if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 16);
select_peripheral(PIOA, pin_mask, PERIPH_A, AT32_GPIOF_PULLUP);
}
static inline void configure_usart2_pins(void)
static inline void configure_usart2_pins(int flags)
{
u32 pin_mask = (1 << 26) | (1 << 27); /* RXD & TXD */
if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 30);
if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 29);
if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 28);
select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP);
}
static inline void configure_usart3_pins(void)
static inline void configure_usart3_pins(int flags)
{
u32 pin_mask = (1 << 18) | (1 << 17); /* RXD & TXD */
if (flags & ATMEL_USART_RTS) pin_mask |= (1 << 16);
if (flags & ATMEL_USART_CTS) pin_mask |= (1 << 15);
if (flags & ATMEL_USART_CLK) pin_mask |= (1 << 19);
select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP);
}
static struct platform_device *__initdata at32_usarts[4];
void __init at32_map_usart(unsigned int hw_id, unsigned int line)
void __init at32_map_usart(unsigned int hw_id, unsigned int line, int flags)
{
struct platform_device *pdev;
switch (hw_id) {
case 0:
pdev = &atmel_usart0_device;
configure_usart0_pins();
configure_usart0_pins(flags);
break;
case 1:
pdev = &atmel_usart1_device;
configure_usart1_pins();
configure_usart1_pins(flags);
break;
case 2:
pdev = &atmel_usart2_device;
configure_usart2_pins();
configure_usart2_pins(flags);
break;
case 3:
pdev = &atmel_usart3_device;
configure_usart3_pins();
configure_usart3_pins(flags);
break;
default:
return;
......
......@@ -26,12 +26,17 @@ static inline void __deprecated at32_add_system_devices(void)
#define ATMEL_MAX_UART 4
extern struct platform_device *atmel_default_console_device;
/* Flags for selecting USART extra pins */
#define ATMEL_USART_RTS 0x01
#define ATMEL_USART_CTS 0x02
#define ATMEL_USART_CLK 0x03
struct atmel_uart_data {
short use_dma_tx; /* use transmit DMA? */
short use_dma_rx; /* use receive DMA? */
void __iomem *regs; /* virtual base address, if any */
};
void at32_map_usart(unsigned int hw_id, unsigned int line);
void at32_map_usart(unsigned int hw_id, unsigned int line, int flags);
struct platform_device *at32_add_device_usart(unsigned int id);
struct eth_platform_data {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment