hv/hv_kvp_daemon: Some small fixes for handling NM keyfiles

Some small fixes:
 - lets make sure we are not adding ipv4 addresses in ipv6 section in
   keyfile and vice versa.
 - ADDR_FAMILY_IPV6 is a bit in addr_family. Test that bit instead of
   checking the whole value of addr_family.
 - Some trivial fixes in hv_set_ifconfig.sh.

These fixes are proposed after doing some internal testing at Red Hat.

CC: Shradha Gupta <shradhagupta@linux.microsoft.com>
CC: Saurabh Sengar <ssengar@linux.microsoft.com>
Fixes: 42999c90 ("hv/hv_kvp_daemon:Support for keyfile based connection profile")
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Shradha Gupta <Shradhagupta@linux.microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20231016133122.2419537-1-anisinha@redhat.com>

tools/hv/hv_kvp_daemon.c

@@ -1421,7 +1421,7 @@ static int kvp_set_ip_info(char *if_name, struct hv_kvp_ipaddr_value *new_val)
 	if (error)
 		goto setval_error;
 
-	if (new_val->addr_family == ADDR_FAMILY_IPV6) {
+	if (new_val->addr_family & ADDR_FAMILY_IPV6) {
 		error = fprintf(nmfile, "\n[ipv6]\n");
 		if (error < 0)
 			goto setval_error;
@@ -1455,14 +1455,18 @@ static int kvp_set_ip_info(char *if_name, struct hv_kvp_ipaddr_value *new_val)
 	if (error < 0)
 		goto setval_error;
 
-	error = fprintf(nmfile, "gateway=%s\n", (char *)new_val->gate_way);
-	if (error < 0)
-		goto setval_error;
-
-	error = fprintf(nmfile, "dns=%s\n", (char *)new_val->dns_addr);
-	if (error < 0)
-		goto setval_error;
+	/* we do not want ipv4 addresses in ipv6 section and vice versa */
+	if (is_ipv6 != is_ipv4((char *)new_val->gate_way)) {
+		error = fprintf(nmfile, "gateway=%s\n", (char *)new_val->gate_way);
+		if (error < 0)
+			goto setval_error;
+	}
 
+	if (is_ipv6 != is_ipv4((char *)new_val->dns_addr)) {
+		error = fprintf(nmfile, "dns=%s\n", (char *)new_val->dns_addr);
+		if (error < 0)
+			goto setval_error;
+	}
 	fclose(nmfile);
 	fclose(ifcfg_file);
 

tools/hv/hv_set_ifconfig.sh

@@ -53,7 +53,7 @@
 #                       or "manual" if no boot-time protocol should be used)
 #
 # address1=ipaddr1/plen
-# address=ipaddr2/plen
+# address2=ipaddr2/plen
 #
 # gateway=gateway1;gateway2
 #
@@ -61,7 +61,7 @@
 #
 # [ipv6]
 # address1=ipaddr1/plen
-# address2=ipaddr1/plen
+# address2=ipaddr2/plen
 #
 # gateway=gateway1;gateway2
 #