Merge branch 'ib-move-axp209' of /home/linus/linux-gpio into devel

Documentation/devicetree/bindings/gpio/gpio-axp209.txt

-AXP209 GPIO controller
+AXP209 GPIO & pinctrl controller
 
 This driver follows the usual GPIO bindings found in
 Documentation/devicetree/bindings/gpio/gpio.txt
 
+This driver follows the usual pinctrl bindings found in
+Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+This driver employs the per-pin muxing pattern.
+
 Required properties:
-- compatible: Should be "x-powers,axp209-gpio"
+- compatible: Should be one of:
+	- "x-powers,axp209-gpio"
+	- "x-powers,axp813-gpio"
 - #gpio-cells: Should be two. The first cell is the pin number and the
   second is the GPIO flags.
 - gpio-controller: Marks the device node as a GPIO controller.
@@ -28,3 +35,41 @@ axp209: pmic@34 {
 		#gpio-cells = <2>;
 	};
 };
+
+The GPIOs can be muxed to other functions and therefore, must be a subnode of
+axp_gpio.
+
+Example:
+
+&axp_gpio {
+	gpio0_adc: gpio0-adc {
+		pins = "GPIO0";
+		function = "adc";
+	};
+};
+
+&example_node {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio0_adc>;
+};
+
+GPIOs and their functions
+-------------------------
+
+Each GPIO is independent from the other (i.e. GPIO0 in gpio_in function does
+not force GPIO1 and GPIO2 to be in gpio_in function as well).
+
+axp209
+------
+GPIO	|	Functions
+------------------------
+GPIO0	|	gpio_in, gpio_out, ldo, adc
+GPIO1	|	gpio_in, gpio_out, ldo, adc
+GPIO2	|	gpio_in, gpio_out
+
+axp813
+------
+GPIO	|	Functions
+------------------------
+GPIO0	|	gpio_in, gpio_out, ldo, adc
+GPIO1	|	gpio_in, gpio_out, ldo

drivers/gpio/Kconfig

@@ -122,12 +122,6 @@ config GPIO_ATH79
 	  Select this option to enable GPIO driver for
 	  Atheros AR71XX/AR724X/AR913X SoC devices.
 
-config GPIO_AXP209
-	tristate "X-Powers AXP209 PMIC GPIO Support"
-	depends on MFD_AXP20X
-	help
-	  Say yes to enable GPIO support for the AXP209 PMIC
-
 config GPIO_BCM_KONA
 	bool "Broadcom Kona GPIO"
 	depends on OF_GPIO && (ARCH_BCM_MOBILE || COMPILE_TEST)

drivers/gpio/Makefile

@@ -32,7 +32,6 @@ obj-$(CONFIG_GPIO_AMDPT)	+= gpio-amdpt.o
 obj-$(CONFIG_GPIO_ARIZONA)	+= gpio-arizona.o
 obj-$(CONFIG_GPIO_ATH79)	+= gpio-ath79.o
 obj-$(CONFIG_GPIO_ASPEED)	+= gpio-aspeed.o
-obj-$(CONFIG_GPIO_AXP209)	+= gpio-axp209.o
 obj-$(CONFIG_GPIO_BCM_KONA)	+= gpio-bcm-kona.o
 obj-$(CONFIG_GPIO_BD9571MWV)	+= gpio-bd9571mwv.o
 obj-$(CONFIG_GPIO_BRCMSTB)	+= gpio-brcmstb.o

drivers/gpio/gpio-axp209.c

-/*
- * AXP20x GPIO driver
- *
- * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under  the terms of the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/bitops.h>
-#include <linux/device.h>
-#include <linux/gpio/driver.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/mfd/axp20x.h>
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/platform_device.h>
-#include <linux/regmap.h>
-#include <linux/slab.h>
-
-#define AXP20X_GPIO_FUNCTIONS		0x7
-#define AXP20X_GPIO_FUNCTION_OUT_LOW	0
-#define AXP20X_GPIO_FUNCTION_OUT_HIGH	1
-#define AXP20X_GPIO_FUNCTION_INPUT	2
-
-struct axp20x_gpio {
-	struct gpio_chip	chip;
-	struct regmap		*regmap;
-};
-
-static int axp20x_gpio_get_reg(unsigned offset)
-{
-	switch (offset) {
-	case 0:
-		return AXP20X_GPIO0_CTRL;
-	case 1:
-		return AXP20X_GPIO1_CTRL;
-	case 2:
-		return AXP20X_GPIO2_CTRL;
-	}
-
-	return -EINVAL;
-}
-
-static int axp20x_gpio_input(struct gpio_chip *chip, unsigned offset)
-{
-	struct axp20x_gpio *gpio = gpiochip_get_data(chip);
-	int reg;
-
-	reg = axp20x_gpio_get_reg(offset);
-	if (reg < 0)
-		return reg;
-
-	return regmap_update_bits(gpio->regmap, reg,
-				  AXP20X_GPIO_FUNCTIONS,
-				  AXP20X_GPIO_FUNCTION_INPUT);
-}
-
-static int axp20x_gpio_get(struct gpio_chip *chip, unsigned offset)
-{
-	struct axp20x_gpio *gpio = gpiochip_get_data(chip);
-	unsigned int val;
-	int ret;
-
-	ret = regmap_read(gpio->regmap, AXP20X_GPIO20_SS, &val);
-	if (ret)
-		return ret;
-
-	return !!(val & BIT(offset + 4));
-}
-
-static int axp20x_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
-{
-	struct axp20x_gpio *gpio = gpiochip_get_data(chip);
-	unsigned int val;
-	int reg, ret;
-
-	reg = axp20x_gpio_get_reg(offset);
-	if (reg < 0)
-		return reg;
-
-	ret = regmap_read(gpio->regmap, reg, &val);
-	if (ret)
-		return ret;
-
-	/*
-	 * This shouldn't really happen if the pin is in use already,
-	 * or if it's not in use yet, it doesn't matter since we're
-	 * going to change the value soon anyway. Default to output.
-	 */
-	if ((val & AXP20X_GPIO_FUNCTIONS) > 2)
-		return 0;
-
-	/*
-	 * The GPIO directions are the three lowest values.
-	 * 2 is input, 0 and 1 are output
-	 */
-	return val & 2;
-}
-
-static int axp20x_gpio_output(struct gpio_chip *chip, unsigned offset,
-			      int value)
-{
-	struct axp20x_gpio *gpio = gpiochip_get_data(chip);
-	int reg;
-
-	reg = axp20x_gpio_get_reg(offset);
-	if (reg < 0)
-		return reg;
-
-	return regmap_update_bits(gpio->regmap, reg,
-				  AXP20X_GPIO_FUNCTIONS,
-				  value ? AXP20X_GPIO_FUNCTION_OUT_HIGH
-				  : AXP20X_GPIO_FUNCTION_OUT_LOW);
-}
-
-static void axp20x_gpio_set(struct gpio_chip *chip, unsigned offset,
-			    int value)
-{
-	axp20x_gpio_output(chip, offset, value);
-}
-
-static int axp20x_gpio_probe(struct platform_device *pdev)
-{
-	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
-	struct axp20x_gpio *gpio;
-	int ret;
-
-	if (!of_device_is_available(pdev->dev.of_node))
-		return -ENODEV;
-
-	if (!axp20x) {
-		dev_err(&pdev->dev, "Parent drvdata not set\n");
-		return -EINVAL;
-	}
-
-	gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
-	if (!gpio)
-		return -ENOMEM;
-
-	gpio->chip.base			= -1;
-	gpio->chip.can_sleep		= true;
-	gpio->chip.parent		= &pdev->dev;
-	gpio->chip.label		= dev_name(&pdev->dev);
-	gpio->chip.owner		= THIS_MODULE;
-	gpio->chip.get			= axp20x_gpio_get;
-	gpio->chip.get_direction	= axp20x_gpio_get_direction;
-	gpio->chip.set			= axp20x_gpio_set;
-	gpio->chip.direction_input	= axp20x_gpio_input;
-	gpio->chip.direction_output	= axp20x_gpio_output;
-	gpio->chip.ngpio		= 3;
-
-	gpio->regmap = axp20x->regmap;
-
-	ret = devm_gpiochip_add_data(&pdev->dev, &gpio->chip, gpio);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to register GPIO chip\n");
-		return ret;
-	}
-
-	dev_info(&pdev->dev, "AXP209 GPIO driver loaded\n");
-
-	return 0;
-}
-
-static const struct of_device_id axp20x_gpio_match[] = {
-	{ .compatible = "x-powers,axp209-gpio" },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, axp20x_gpio_match);
-
-static struct platform_driver axp20x_gpio_driver = {
-	.probe		= axp20x_gpio_probe,
-	.driver = {
-		.name		= "axp20x-gpio",
-		.of_match_table	= axp20x_gpio_match,
-	},
-};
-
-module_platform_driver(axp20x_gpio_driver);
-
-MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
-MODULE_DESCRIPTION("AXP20x PMIC GPIO driver");
-MODULE_LICENSE("GPL");

drivers/pinctrl/Kconfig

@@ -63,6 +63,16 @@ config PINCTRL_AS3722
 	  open drain configuration for the GPIO pins of AS3722 devices. It also
 	  supports the GPIO functionality through gpiolib.
 
+config PINCTRL_AXP209
+	tristate "X-Powers AXP209 PMIC pinctrl and GPIO Support"
+	depends on MFD_AXP20X
+	help
+	  AXP PMICs provides multiple GPIOs that can be muxed for different
+	  functions. This driver bundles a pinctrl driver to select the function
+	  muxing and a GPIO driver to handle the GPIO when the GPIO function is
+	  selected.
+	  Say yes to enable pinctrl and GPIO support for the AXP209 PMIC
+
 config PINCTRL_BF54x
 	def_bool y if BF54x
 	select PINCTRL_ADI2

drivers/pinctrl/Makefile

@@ -11,6 +11,7 @@ obj-$(CONFIG_GENERIC_PINCONF)	+= pinconf-generic.o
 obj-$(CONFIG_PINCTRL_ADI2)	+= pinctrl-adi2.o
 obj-$(CONFIG_PINCTRL_ARTPEC6)	+= pinctrl-artpec6.o
 obj-$(CONFIG_PINCTRL_AS3722)	+= pinctrl-as3722.o
+obj-$(CONFIG_PINCTRL_AXP209)	+= pinctrl-axp209.o
 obj-$(CONFIG_PINCTRL_BF54x)	+= pinctrl-adi2-bf54x.o
 obj-$(CONFIG_PINCTRL_BF60x)	+= pinctrl-adi2-bf60x.o
 obj-$(CONFIG_PINCTRL_AT91)	+= pinctrl-at91.o