Commit caef9f07 authored by Manish Narani's avatar Manish Narani Committed by Greg Kroah-Hartman

dt-bindings: usb: dwc3-xilinx: Add documentation for Versal DWC3 Controller

Add documentation for Versal DWC3 controller. Add required property
'reg' for the same. Also add optional properties for snps,dwc3.
Reviewed-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarManish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1615963949-75320-2-git-send-email-manish.narani@xilinx.comSigned-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 3af32605
Xilinx SuperSpeed DWC3 USB SoC controller
Required properties:
- compatible: Should contain "xlnx,zynqmp-dwc3"
- compatible: May contain "xlnx,zynqmp-dwc3" or "xlnx,versal-dwc3"
- reg: Base address and length of the register control block
- clocks: A list of phandles for the clocks listed in clock-names
- clock-names: Should contain the following:
"bus_clk" Master/Core clock, have to be >= 125 MHz for SS
operation and >= 60MHz for HS operation
"ref_clk" Clock source to core during PHY power down
- resets: A list of phandles for resets listed in reset-names
- reset-names:
"usb_crst" USB core reset
"usb_hibrst" USB hibernation reset
"usb_apbrst" USB APB reset
Required child node:
A child node must exist to represent the core DWC3 IP block. The name of
the node is not important. The content of the node is defined in dwc3.txt.
Optional properties for snps,dwc3:
- dma-coherent: Enable this flag if CCI is enabled in design. Adding this
flag configures Global SoC bus Configuration Register and
Xilinx USB 3.0 IP - USB coherency register to enable CCI.
- interrupt-names: Should contain the following:
"dwc_usb3" USB gadget mode interrupts
"otg" USB OTG mode interrupts
"hiber" USB hibernation interrupts
Example device node:
usb@0 {
#address-cells = <0x2>;
#size-cells = <0x1>;
compatible = "xlnx,zynqmp-dwc3";
reg = <0x0 0xff9d0000 0x0 0x100>;
clock-names = "bus_clk", "ref_clk";
clocks = <&clk125>, <&clk125>;
resets = <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>,
<&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>,
<&zynqmp_reset ZYNQMP_RESET_USB1_APB>;
reset-names = "usb_crst", "usb_hibrst", "usb_apbrst";
ranges;
dwc3@fe200000 {
compatible = "snps,dwc3";
reg = <0x0 0xfe200000 0x40000>;
interrupts = <0x0 0x41 0x4>;
interrupt-names = "dwc_usb3", "otg", "hiber";
interrupts = <0 65 4>, <0 69 4>, <0 75 4>;
phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
phy-names = "usb3-phy";
dr_mode = "host";
dma-coherent;
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment