Commit cc31cdbe authored by Can Guo's avatar Can Guo Committed by Kishon Vijay Abraham I

phy: Add QMP phy based UFS phy support for sdm845

Add UFS PHY support to make SDM845 UFS work with common PHY framework.
Signed-off-by: default avatarCan Guo <cang@codeaurora.org>
Reviewed-by: default avatarEvan Green <evgreen@chromium.org>
Reviewed-by: default avatarVivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: default avatarKishon Vijay Abraham I <kishon@ti.com>
parent 6b045268
......@@ -156,6 +156,11 @@ static const unsigned int qmp_v3_usb3phy_regs_layout[] = {
[QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x170,
};
static const unsigned int sdm845_ufsphy_regs_layout[] = {
[QPHY_START_CTRL] = 0x00,
[QPHY_PCS_READY_STATUS] = 0x160,
};
static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = {
QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c),
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
......@@ -601,6 +606,83 @@ static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_pcs_tbl[] = {
QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG2, 0x60),
};
static const struct qmp_phy_init_tbl sdm845_ufsphy_serdes_tbl[] = {
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x04),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_BG_TIMER, 0x0a),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x06),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0xd5),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL, 0x20),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x00),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x01),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_CTRL, 0x00),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x04),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x05),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_INITVAL1, 0xff),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_INITVAL2, 0x00),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xda),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0xff),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x0c),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE1, 0x98),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE1, 0x06),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE1, 0x16),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE1, 0x36),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE1, 0x3f),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE1, 0x00),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE1, 0xc1),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE1, 0x00),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE1, 0x32),
QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE1, 0x0f),
/* Rate B */
QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x44),
};
static const struct qmp_phy_init_tbl sdm845_ufsphy_tx_tbl[] = {
QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0x06),
QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x04),
QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x07),
};
static const struct qmp_phy_init_tbl sdm845_ufsphy_rx_tbl[] = {
QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_LVL, 0x24),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x0f),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x1e),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_INTERFACE_MODE, 0x40),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_TERM_BW, 0x5b),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x06),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1b),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN_HALF, 0x04),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN_QUARTER, 0x04),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN, 0x04),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_PI_CONTROLS, 0x81),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80),
QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x59),
};
static const struct qmp_phy_init_tbl sdm845_ufsphy_pcs_tbl[] = {
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_CTRL2, 0x6e),
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TX_LARGE_AMP_DRV_LVL, 0x0a),
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TX_SMALL_AMP_DRV_LVL, 0x02),
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SYM_RESYNC_CTRL, 0x03),
QMP_PHY_INIT_CFG(QPHY_V3_PCS_TX_MID_TERM_CTRL1, 0x43),
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_CTRL1, 0x0f),
QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_MIN_HIBERN8_TIME, 0x9a),
QMP_PHY_INIT_CFG(QPHY_V3_PCS_MULTI_LANE_CTRL1, 0x02),
};
/* struct qmp_phy_cfg - per-PHY initialization config */
struct qmp_phy_cfg {
......@@ -654,6 +736,9 @@ struct qmp_phy_cfg {
/* Register offset of secondary tx/rx lanes for USB DP combo PHY */
unsigned int tx_b_lane_offset;
unsigned int rx_b_lane_offset;
/* true, if PCS block has no separate SW_RESET register */
bool no_pcs_sw_reset;
};
/**
......@@ -750,6 +835,10 @@ static const char * const qmp_v3_phy_clk_l[] = {
"aux", "cfg_ahb", "ref", "com_aux",
};
static const char * const sdm845_ufs_phy_clk_l[] = {
"ref", "ref_aux",
};
/* list of resets */
static const char * const msm8996_pciephy_reset_l[] = {
"phy", "common", "cfg",
......@@ -919,6 +1008,35 @@ static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
.pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
};
static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
.type = PHY_TYPE_UFS,
.nlanes = 2,
.serdes_tbl = sdm845_ufsphy_serdes_tbl,
.serdes_tbl_num = ARRAY_SIZE(sdm845_ufsphy_serdes_tbl),
.tx_tbl = sdm845_ufsphy_tx_tbl,
.tx_tbl_num = ARRAY_SIZE(sdm845_ufsphy_tx_tbl),
.rx_tbl = sdm845_ufsphy_rx_tbl,
.rx_tbl_num = ARRAY_SIZE(sdm845_ufsphy_rx_tbl),
.pcs_tbl = sdm845_ufsphy_pcs_tbl,
.pcs_tbl_num = ARRAY_SIZE(sdm845_ufsphy_pcs_tbl),
.clk_list = sdm845_ufs_phy_clk_l,
.num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
.vreg_list = qmp_phy_vreg_l,
.num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
.regs = sdm845_ufsphy_regs_layout,
.start_ctrl = SERDES_START,
.pwrdn_ctrl = SW_PWRDN,
.mask_pcs_ready = PCS_READY,
.is_dual_lane_phy = true,
.tx_b_lane_offset = 0x400,
.rx_b_lane_offset = 0x400,
.no_pcs_sw_reset = true,
};
static void qcom_qmp_phy_configure(void __iomem *base,
const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
......@@ -1130,6 +1248,14 @@ static int qcom_qmp_phy_init(struct phy *phy)
qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
/*
* UFS PHY requires the deassert of software reset before serdes start.
* For UFS PHYs that do not have software reset control bits, defer
* starting serdes until the power on callback.
*/
if ((cfg->type == PHY_TYPE_UFS) && cfg->no_pcs_sw_reset)
goto out;
/*
* Pull out PHY from POWER DOWN state.
* This is active low enable signal to power-down PHY.
......@@ -1159,6 +1285,7 @@ static int qcom_qmp_phy_init(struct phy *phy)
}
qmp->phy_initialized = true;
out:
return ret;
err_pcs_ready:
......@@ -1181,7 +1308,8 @@ static int qcom_qmp_phy_exit(struct phy *phy)
clk_disable_unprepare(qphy->pipe_clk);
/* PHY reset */
qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
if (!cfg->no_pcs_sw_reset)
qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
/* stop SerDes and Phy-Coding-Sublayer */
qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
......@@ -1199,6 +1327,44 @@ static int qcom_qmp_phy_exit(struct phy *phy)
return 0;
}
static int qcom_qmp_phy_poweron(struct phy *phy)
{
struct qmp_phy *qphy = phy_get_drvdata(phy);
struct qcom_qmp *qmp = qphy->qmp;
const struct qmp_phy_cfg *cfg = qmp->cfg;
void __iomem *pcs = qphy->pcs;
void __iomem *status;
unsigned int mask, val;
int ret = 0;
if (cfg->type != PHY_TYPE_UFS)
return 0;
/*
* For UFS PHY that has not software reset control, serdes start
* should only happen when UFS driver explicitly calls phy_power_on
* after it deasserts software reset.
*/
if (cfg->no_pcs_sw_reset && !qmp->phy_initialized &&
(qmp->init_count != 0)) {
/* start SerDes and Phy-Coding-Sublayer */
qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
mask = cfg->mask_pcs_ready;
ret = readl_poll_timeout(status, val, !(val & mask), 1,
PHY_INIT_COMPLETE_TIMEOUT);
if (ret) {
dev_err(qmp->dev, "phy initialization timed-out\n");
return ret;
}
qmp->phy_initialized = true;
}
return ret;
}
static int qcom_qmp_phy_set_mode(struct phy *phy, enum phy_mode mode)
{
struct qmp_phy *qphy = phy_get_drvdata(phy);
......@@ -1428,6 +1594,7 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
static const struct phy_ops qcom_qmp_phy_gen_ops = {
.init = qcom_qmp_phy_init,
.exit = qcom_qmp_phy_exit,
.power_on = qcom_qmp_phy_poweron,
.set_mode = qcom_qmp_phy_set_mode,
.owner = THIS_MODULE,
};
......@@ -1530,6 +1697,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
}, {
.compatible = "qcom,sdm845-qmp-usb3-uni-phy",
.data = &qmp_v3_usb3_uniphy_cfg,
}, {
.compatible = "qcom,sdm845-qmp-ufs-phy",
.data = &sdm845_ufsphy_cfg,
},
{ },
};
......
......@@ -184,6 +184,8 @@
#define QSERDES_V3_COM_VCO_TUNE2_MODE0 0x0f8
#define QSERDES_V3_COM_VCO_TUNE1_MODE1 0x0fc
#define QSERDES_V3_COM_VCO_TUNE2_MODE1 0x100
#define QSERDES_V3_COM_VCO_TUNE_INITVAL1 0x104
#define QSERDES_V3_COM_VCO_TUNE_INITVAL2 0x108
#define QSERDES_V3_COM_VCO_TUNE_TIMER1 0x11c
#define QSERDES_V3_COM_VCO_TUNE_TIMER2 0x120
#define QSERDES_V3_COM_CLK_SELECT 0x138
......@@ -211,8 +213,13 @@
/* Only for QMP V3 PHY - RX registers */
#define QSERDES_V3_RX_UCDR_SO_GAIN_HALF 0x00c
#define QSERDES_V3_RX_UCDR_SO_GAIN 0x014
#define QSERDES_V3_RX_UCDR_SVS_SO_GAIN_HALF 0x024
#define QSERDES_V3_RX_UCDR_SVS_SO_GAIN_QUARTER 0x028
#define QSERDES_V3_RX_UCDR_SVS_SO_GAIN 0x02c
#define QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN 0x030
#define QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE 0x034
#define QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_LOW 0x03c
#define QSERDES_V3_RX_UCDR_PI_CONTROLS 0x044
#define QSERDES_V3_RX_RX_TERM_BW 0x07c
#define QSERDES_V3_RX_VGA_CAL_CNTRL1 0x0bc
#define QSERDES_V3_RX_VGA_CAL_CNTRL2 0x0c0
......@@ -239,6 +246,8 @@
#define QPHY_V3_PCS_TXMGN_V3 0x018
#define QPHY_V3_PCS_TXMGN_V4 0x01c
#define QPHY_V3_PCS_TXMGN_LS 0x020
#define QPHY_V3_PCS_TX_LARGE_AMP_DRV_LVL 0x02c
#define QPHY_V3_PCS_TX_SMALL_AMP_DRV_LVL 0x034
#define QPHY_V3_PCS_TXDEEMPH_M6DB_V0 0x024
#define QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0 0x028
#define QPHY_V3_PCS_TXDEEMPH_M6DB_V1 0x02c
......@@ -275,6 +284,12 @@
#define QPHY_V3_PCS_FLL_CNT_VAL_L 0x0cc
#define QPHY_V3_PCS_FLL_CNT_VAL_H_TOL 0x0d0
#define QPHY_V3_PCS_FLL_MAN_CODE 0x0d4
#define QPHY_V3_PCS_RX_SYM_RESYNC_CTRL 0x134
#define QPHY_V3_PCS_RX_MIN_HIBERN8_TIME 0x138
#define QPHY_V3_PCS_RX_SIGDET_CTRL1 0x13c
#define QPHY_V3_PCS_RX_SIGDET_CTRL2 0x140
#define QPHY_V3_PCS_TX_MID_TERM_CTRL1 0x1bc
#define QPHY_V3_PCS_MULTI_LANE_CTRL1 0x1c4
#define QPHY_V3_PCS_RX_SIGDET_LVL 0x1d8
#define QPHY_V3_PCS_REFGEN_REQ_CONFIG1 0x20c
#define QPHY_V3_PCS_REFGEN_REQ_CONFIG2 0x210
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment