Merge remote-tracking branch 'scott/next' into next

Freescale updates from Scott. Mostly support for critical
and machine check exceptions on 64-bit BookE, some new
PCI suspend/resume work and misc bits.

Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt

+Freescale L2 Cache Controller
+
+L2 cache is present in Freescale's QorIQ and QorIQ Qonverge platforms.
+The cache bindings explained below are ePAPR compliant
+
+Required Properties:
+
+- compatible	: Should include "fsl,chip-l2-cache-controller" and "cache"
+		  where chip is the processor (bsc9132, npc8572 etc.)
+- reg		: Address and size of L2 cache controller registers
+- cache-size	: Size of the entire L2 cache
+- interrupts	: Error interrupt of L2 controller
+- cache-line-size : Size of L2 cache lines
+
+Example:
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,bsc9132-l2-cache-controller", "cache";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>; // 32 bytes
+		cache-size = <0x40000>; // L2,256K
+		interrupts = <16 2 1 0>;
+	};

Documentation/devicetree/bindings/powerpc/fsl/mem-ctrlr.txt

+Freescale DDR memory controller
+
+Properties:
+
+- compatible	: Should include "fsl,chip-memory-controller" where
+		  chip is the processor (bsc9132, mpc8572 etc.), or
+		  "fsl,qoriq-memory-controller".
+- reg		: Address and size of DDR controller registers
+- interrupts	: Error interrupt of DDR controller
+
+Example 1:
+
+	memory-controller@2000 {
+		compatible = "fsl,bsc9132-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <16 2 1 8>;
+	};
+
+
+Example 2:
+
+	ddr1: memory-controller@8000 {
+		compatible = "fsl,qoriq-memory-controller-v4.7",
+				"fsl,qoriq-memory-controller";
+		reg = <0x8000 0x1000>;
+		interrupts = <16 2 1 23>;
+	};

Documentation/devicetree/bindings/usb/fsl-usb.txt

@@ -8,7 +8,9 @@ and additions :
 Required properties :
  - compatible : Should be "fsl-usb2-mph" for multi port host USB
    controllers, or "fsl-usb2-dr" for dual role USB controllers
-   or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121
+   or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121.
+   Wherever applicable, the IP version of the USB controller should
+   also be mentioned (for eg. fsl-usb2-dr-v2.2 for bsc9132).
  - phy_type : For multi port host USB controllers, should be one of
    "ulpi", or "serial". For dual role USB controllers, should be
    one of "ulpi", "utmi", "utmi_wide", or "serial".

arch/powerpc/boot/dts/fsl/b4420si-post.dtsi

@@ -86,6 +86,42 @@ guts: global-utilities@e0000 {
 
 	clockgen: global-utilities@e1000 {
 		compatible = "fsl,b4420-clockgen", "fsl,qoriq-clockgen-2.0";
+		ranges = <0x0 0xe1000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysclk: sysclk {
+			#clock-cells = <0>;
+			compatible = "fsl,qoriq-sysclk-2.0";
+			clock-output-names = "sysclk";
+		};
+
+		pll0: pll0@800 {
+			#clock-cells = <1>;
+			reg = <0x800 0x4>;
+			compatible = "fsl,qoriq-core-pll-2.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll0", "pll0-div2", "pll0-div4";
+		};
+
+		pll1: pll1@820 {
+			#clock-cells = <1>;
+			reg = <0x820 0x4>;
+			compatible = "fsl,qoriq-core-pll-2.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll1", "pll1-div2", "pll1-div4";
+		};
+
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 0x4>;
+			compatible = "fsl,qoriq-core-mux-2.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+				<&pll1 0>, <&pll1 1>, <&pll1 2>;
+			clock-names = "pll0", "pll0-div2", "pll0-div4",
+				"pll1", "pll1-div2", "pll1-div4";
+			clock-output-names = "cmux0";
+		};
 	};
 
 	rcpm: global-utilities@e2000 {

arch/powerpc/boot/dts/fsl/b4420si-pre.dtsi

@@ -64,11 +64,13 @@ cpus {
 		cpu0: PowerPC,e6500@0 {
 			device_type = "cpu";
 			reg = <0 1>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2>;
 		};
 		cpu1: PowerPC,e6500@2 {
 			device_type = "cpu";
 			reg = <2 3>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2>;
 		};
 	};

arch/powerpc/boot/dts/fsl/b4860si-post.dtsi

@@ -130,6 +130,42 @@ guts: global-utilities@e0000 {
 
 	clockgen: global-utilities@e1000 {
 		compatible = "fsl,b4860-clockgen", "fsl,qoriq-clockgen-2.0";
+		ranges = <0x0 0xe1000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysclk: sysclk {
+			#clock-cells = <0>;
+			compatible = "fsl,qoriq-sysclk-2.0";
+			clock-output-names = "sysclk";
+		};
+
+		pll0: pll0@800 {
+			#clock-cells = <1>;
+			reg = <0x800 0x4>;
+			compatible = "fsl,qoriq-core-pll-2.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll0", "pll0-div2", "pll0-div4";
+		};
+
+		pll1: pll1@820 {
+			#clock-cells = <1>;
+			reg = <0x820 0x4>;
+			compatible = "fsl,qoriq-core-pll-2.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll1", "pll1-div2", "pll1-div4";
+		};
+
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 0x4>;
+			compatible = "fsl,qoriq-core-mux-2.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+				<&pll1 0>, <&pll1 1>, <&pll1 2>;
+			clock-names = "pll0", "pll0-div2", "pll0-div4",
+				"pll1", "pll1-div2", "pll1-div4";
+			clock-output-names = "cmux0";
+		};
 	};
 
 	rcpm: global-utilities@e2000 {

arch/powerpc/boot/dts/fsl/b4860si-pre.dtsi

@@ -64,21 +64,25 @@ cpus {
 		cpu0: PowerPC,e6500@0 {
 			device_type = "cpu";
 			reg = <0 1>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2>;
 		};
 		cpu1: PowerPC,e6500@2 {
 			device_type = "cpu";
 			reg = <2 3>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2>;
 		};
 		cpu2: PowerPC,e6500@4 {
 			device_type = "cpu";
 			reg = <4 5>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2>;
 		};
 		cpu3: PowerPC,e6500@6 {
 			device_type = "cpu";
 			reg = <6 7>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2>;
 		};
 	};

arch/powerpc/boot/dts/fsl/p2041si-post.dtsi

@@ -306,8 +306,68 @@ pins: global-utilities@e0e00 {
 
 	clockgen: global-utilities@e1000 {
 		compatible = "fsl,p2041-clockgen", "fsl,qoriq-clockgen-1.0";
+		ranges = <0x0 0xe1000 0x1000>;
 		reg = <0xe1000 0x1000>;
 		clock-frequency = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysclk: sysclk {
+			#clock-cells = <0>;
+			compatible = "fsl,qoriq-sysclk-1.0";
+			clock-output-names = "sysclk";
+		};
+
+		pll0: pll0@800 {
+			#clock-cells = <1>;
+			reg = <0x800 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll0", "pll0-div2";
+		};
+
+		pll1: pll1@820 {
+			#clock-cells = <1>;
+			reg = <0x820 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll1", "pll1-div2";
+		};
+
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux0";
+		};
+
+		mux1: mux1@20 {
+			#clock-cells = <0>;
+			reg = <0x20 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux1";
+		};
+
+		mux2: mux2@40 {
+			#clock-cells = <0>;
+			reg = <0x40 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+		};
+
+		mux3: mux3@60 {
+			#clock-cells = <0>;
+			reg = <0x60 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux3";
+		};
 	};
 
 	rcpm: global-utilities@e2000 {

arch/powerpc/boot/dts/fsl/p2041si-pre.dtsi

@@ -81,6 +81,7 @@ cpus {
 		cpu0: PowerPC,e500mc@0 {
 			device_type = "cpu";
 			reg = <0>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
 				next-level-cache = <&cpc>;
@@ -89,6 +90,7 @@ L2_0: l2-cache {
 		cpu1: PowerPC,e500mc@1 {
 			device_type = "cpu";
 			reg = <1>;
+			clocks = <&mux1>;
 			next-level-cache = <&L2_1>;
 			L2_1: l2-cache {
 				next-level-cache = <&cpc>;
@@ -97,6 +99,7 @@ L2_1: l2-cache {
 		cpu2: PowerPC,e500mc@2 {
 			device_type = "cpu";
 			reg = <2>;
+			clocks = <&mux2>;
 			next-level-cache = <&L2_2>;
 			L2_2: l2-cache {
 				next-level-cache = <&cpc>;
@@ -105,6 +108,7 @@ L2_2: l2-cache {
 		cpu3: PowerPC,e500mc@3 {
 			device_type = "cpu";
 			reg = <3>;
+			clocks = <&mux3>;
 			next-level-cache = <&L2_3>;
 			L2_3: l2-cache {
 				next-level-cache = <&cpc>;

arch/powerpc/boot/dts/fsl/p3041si-post.dtsi

@@ -333,8 +333,69 @@ pins: global-utilities@e0e00 {
 
 	clockgen: global-utilities@e1000 {
 		compatible = "fsl,p3041-clockgen", "fsl,qoriq-clockgen-1.0";
+		ranges = <0x0 0xe1000 0x1000>;
 		reg = <0xe1000 0x1000>;
 		clock-frequency = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysclk: sysclk {
+			#clock-cells = <0>;
+			compatible = "fsl,qoriq-sysclk-1.0";
+			clock-output-names = "sysclk";
+		};
+
+		pll0: pll0@800 {
+			#clock-cells = <1>;
+			reg = <0x800 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll0", "pll0-div2";
+		};
+
+		pll1: pll1@820 {
+			#clock-cells = <1>;
+			reg = <0x820 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll1", "pll1-div2";
+		};
+
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux0";
+		};
+
+		mux1: mux1@20 {
+			#clock-cells = <0>;
+			reg = <0x20 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux1";
+		};
+
+		mux2: mux2@40 {
+			#clock-cells = <0>;
+			reg = <0x40 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux2";
+		};
+
+		mux3: mux3@60 {
+			#clock-cells = <0>;
+			reg = <0x60 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux3";
+		};
 	};
 
 	rcpm: global-utilities@e2000 {

arch/powerpc/boot/dts/fsl/p3041si-pre.dtsi

@@ -82,6 +82,7 @@ cpus {
 		cpu0: PowerPC,e500mc@0 {
 			device_type = "cpu";
 			reg = <0>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
 				next-level-cache = <&cpc>;
@@ -90,6 +91,7 @@ L2_0: l2-cache {
 		cpu1: PowerPC,e500mc@1 {
 			device_type = "cpu";
 			reg = <1>;
+			clocks = <&mux1>;
 			next-level-cache = <&L2_1>;
 			L2_1: l2-cache {
 				next-level-cache = <&cpc>;
@@ -98,6 +100,7 @@ L2_1: l2-cache {
 		cpu2: PowerPC,e500mc@2 {
 			device_type = "cpu";
 			reg = <2>;
+			clocks = <&mux2>;
 			next-level-cache = <&L2_2>;
 			L2_2: l2-cache {
 				next-level-cache = <&cpc>;
@@ -106,6 +109,7 @@ L2_2: l2-cache {
 		cpu3: PowerPC,e500mc@3 {
 			device_type = "cpu";
 			reg = <3>;
+			clocks = <&mux3>;
 			next-level-cache = <&L2_3>;
 			L2_3: l2-cache {
 				next-level-cache = <&cpc>;

arch/powerpc/boot/dts/fsl/p4080si-post.dtsi

@@ -353,8 +353,121 @@ pins: global-utilities@e0e00 {
 
 	clockgen: global-utilities@e1000 {
 		compatible = "fsl,p4080-clockgen", "fsl,qoriq-clockgen-1.0";
+		ranges = <0x0 0xe1000 0x1000>;
 		reg = <0xe1000 0x1000>;
 		clock-frequency = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysclk: sysclk {
+			#clock-cells = <0>;
+			compatible = "fsl,qoriq-sysclk-1.0";
+			clock-output-names = "sysclk";
+		};
+
+		pll0: pll0@800 {
+			#clock-cells = <1>;
+			reg = <0x800 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll0", "pll0-div2";
+		};
+
+		pll1: pll1@820 {
+			#clock-cells = <1>;
+			reg = <0x820 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll1", "pll1-div2";
+		};
+
+		pll2: pll2@840 {
+			#clock-cells = <1>;
+			reg = <0x840 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll2", "pll2-div2";
+		};
+
+		pll3: pll3@860 {
+			#clock-cells = <1>;
+			reg = <0x860 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll3", "pll3-div2";
+		};
+
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux0";
+		};
+
+		mux1: mux1@20 {
+			#clock-cells = <0>;
+			reg = <0x20 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux1";
+		};
+
+		mux2: mux2@40 {
+			#clock-cells = <0>;
+			reg = <0x40 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux2";
+		};
+
+		mux3: mux3@60 {
+			#clock-cells = <0>;
+			reg = <0x60 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux3";
+		};
+
+		mux4: mux4@80 {
+			#clock-cells = <0>;
+			reg = <0x80 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll2 0>, <&pll2 1>, <&pll3 0>, <&pll3 1>;
+			clock-names = "pll2", "pll2-div2", "pll3", "pll3-div2";
+			clock-output-names = "cmux4";
+		};
+
+		mux5: mux5@a0 {
+			#clock-cells = <0>;
+			reg = <0xa0 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll2 0>, <&pll2 1>, <&pll3 0>, <&pll3 1>;
+			clock-names = "pll2", "pll2-div2", "pll3", "pll3-div2";
+			clock-output-names = "cmux5";
+		};
+
+		mux6: mux6@c0 {
+			#clock-cells = <0>;
+			reg = <0xc0 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll2 0>, <&pll2 1>, <&pll3 0>, <&pll3 1>;
+			clock-names = "pll2", "pll2-div2", "pll3", "pll3-div2";
+			clock-output-names = "cmux6";
+		};
+
+		mux7: mux7@e0 {
+			#clock-cells = <0>;
+			reg = <0xe0 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll2 0>, <&pll2 1>, <&pll3 0>, <&pll3 1>;
+			clock-names = "pll2", "pll2-div2", "pll3", "pll3-div2";
+			clock-output-names = "cmux7";
+		};
 	};
 
 	rcpm: global-utilities@e2000 {

arch/powerpc/boot/dts/fsl/p4080si-pre.dtsi

@@ -81,6 +81,7 @@ cpus {
 		cpu0: PowerPC,e500mc@0 {
 			device_type = "cpu";
 			reg = <0>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
 				next-level-cache = <&cpc>;
@@ -89,6 +90,7 @@ L2_0: l2-cache {
 		cpu1: PowerPC,e500mc@1 {
 			device_type = "cpu";
 			reg = <1>;
+			clocks = <&mux1>;
 			next-level-cache = <&L2_1>;
 			L2_1: l2-cache {
 				next-level-cache = <&cpc>;
@@ -97,6 +99,7 @@ L2_1: l2-cache {
 		cpu2: PowerPC,e500mc@2 {
 			device_type = "cpu";
 			reg = <2>;
+			clocks = <&mux2>;
 			next-level-cache = <&L2_2>;
 			L2_2: l2-cache {
 				next-level-cache = <&cpc>;
@@ -105,6 +108,7 @@ L2_2: l2-cache {
 		cpu3: PowerPC,e500mc@3 {
 			device_type = "cpu";
 			reg = <3>;
+			clocks = <&mux3>;
 			next-level-cache = <&L2_3>;
 			L2_3: l2-cache {
 				next-level-cache = <&cpc>;
@@ -113,6 +117,7 @@ L2_3: l2-cache {
 		cpu4: PowerPC,e500mc@4 {
 			device_type = "cpu";
 			reg = <4>;
+			clocks = <&mux4>;
 			next-level-cache = <&L2_4>;
 			L2_4: l2-cache {
 				next-level-cache = <&cpc>;
@@ -121,6 +126,7 @@ L2_4: l2-cache {
 		cpu5: PowerPC,e500mc@5 {
 			device_type = "cpu";
 			reg = <5>;
+			clocks = <&mux5>;
 			next-level-cache = <&L2_5>;
 			L2_5: l2-cache {
 				next-level-cache = <&cpc>;
@@ -129,6 +135,7 @@ L2_5: l2-cache {
 		cpu6: PowerPC,e500mc@6 {
 			device_type = "cpu";
 			reg = <6>;
+			clocks = <&mux6>;
 			next-level-cache = <&L2_6>;
 			L2_6: l2-cache {
 				next-level-cache = <&cpc>;
@@ -137,6 +144,7 @@ L2_6: l2-cache {
 		cpu7: PowerPC,e500mc@7 {
 			device_type = "cpu";
 			reg = <7>;
+			clocks = <&mux7>;
 			next-level-cache = <&L2_7>;
 			L2_7: l2-cache {
 				next-level-cache = <&cpc>;

arch/powerpc/boot/dts/fsl/p5020si-post.dtsi

@@ -338,8 +338,51 @@ pins: global-utilities@e0e00 {
 
 	clockgen: global-utilities@e1000 {
 		compatible = "fsl,p5020-clockgen", "fsl,qoriq-clockgen-1.0";
+		ranges = <0x0 0xe1000 0x1000>;
 		reg = <0xe1000 0x1000>;
 		clock-frequency = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysclk: sysclk {
+			#clock-cells = <0>;
+			compatible = "fsl,qoriq-sysclk-1.0";
+			clock-output-names = "sysclk";
+		};
+
+		pll0: pll0@800 {
+			#clock-cells = <1>;
+			reg = <0x800 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll0", "pll0-div2";
+		};
+
+		pll1: pll1@820 {
+			#clock-cells = <1>;
+			reg = <0x820 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll1", "pll1-div2";
+		};
+
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux0";
+		};
+
+		mux1: mux1@20 {
+			#clock-cells = <0>;
+			reg = <0x20 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux1";
+		};
 	};
 
 	rcpm: global-utilities@e2000 {

arch/powerpc/boot/dts/fsl/p5020si-pre.dtsi

@@ -88,6 +88,7 @@ cpus {
 		cpu0: PowerPC,e5500@0 {
 			device_type = "cpu";
 			reg = <0>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
 				next-level-cache = <&cpc>;
@@ -96,6 +97,7 @@ L2_0: l2-cache {
 		cpu1: PowerPC,e5500@1 {
 			device_type = "cpu";
 			reg = <1>;
+			clocks = <&mux1>;
 			next-level-cache = <&L2_1>;
 			L2_1: l2-cache {
 				next-level-cache = <&cpc>;

arch/powerpc/boot/dts/fsl/p5040si-post.dtsi

@@ -298,8 +298,69 @@ pins: global-utilities@e0e00 {
 
 	clockgen: global-utilities@e1000 {
 		compatible = "fsl,p5040-clockgen", "fsl,qoriq-clockgen-1.0";
+		ranges = <0x0 0xe1000 0x1000>;
 		reg = <0xe1000 0x1000>;
 		clock-frequency = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysclk: sysclk {
+			#clock-cells = <0>;
+			compatible = "fsl,qoriq-sysclk-1.0";
+			clock-output-names = "sysclk";
+		};
+
+		pll0: pll0@800 {
+			#clock-cells = <1>;
+			reg = <0x800 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll0", "pll0-div2";
+		};
+
+		pll1: pll1@820 {
+			#clock-cells = <1>;
+			reg = <0x820 0x4>;
+			compatible = "fsl,qoriq-core-pll-1.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll1", "pll1-div2";
+		};
+
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux0";
+		};
+
+		mux1: mux1@20 {
+			#clock-cells = <0>;
+			reg = <0x20 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux1";
+		};
+
+		mux2: mux2@40 {
+			#clock-cells = <0>;
+			reg = <0x40 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux2";
+		};
+
+		mux3: mux3@60 {
+			#clock-cells = <0>;
+			reg = <0x60 0x4>;
+			compatible = "fsl,qoriq-core-mux-1.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>;
+			clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2";
+			clock-output-names = "cmux3";
+		};
 	};
 
 	rcpm: global-utilities@e2000 {

arch/powerpc/boot/dts/fsl/p5040si-pre.dtsi

@@ -81,6 +81,7 @@ cpus {
 		cpu0: PowerPC,e5500@0 {
 			device_type = "cpu";
 			reg = <0>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
 				next-level-cache = <&cpc>;
@@ -89,6 +90,7 @@ L2_0: l2-cache {
 		cpu1: PowerPC,e5500@1 {
 			device_type = "cpu";
 			reg = <1>;
+			clocks = <&mux1>;
 			next-level-cache = <&L2_1>;
 			L2_1: l2-cache {
 				next-level-cache = <&cpc>;
@@ -97,6 +99,7 @@ L2_1: l2-cache {
 		cpu2: PowerPC,e5500@2 {
 			device_type = "cpu";
 			reg = <2>;
+			clocks = <&mux2>;
 			next-level-cache = <&L2_2>;
 			L2_2: l2-cache {
 				next-level-cache = <&cpc>;
@@ -105,6 +108,7 @@ L2_2: l2-cache {
 		cpu3: PowerPC,e5500@3 {
 			device_type = "cpu";
 			reg = <3>;
+			clocks = <&mux3>;
 			next-level-cache = <&L2_3>;
 			L2_3: l2-cache {
 				next-level-cache = <&cpc>;

arch/powerpc/boot/dts/fsl/t4240si-post.dtsi

@@ -369,7 +369,93 @@ guts: global-utilities@e0000 {
 
 	clockgen: global-utilities@e1000 {
 		compatible = "fsl,t4240-clockgen", "fsl,qoriq-clockgen-2.0";
+		ranges = <0x0 0xe1000 0x1000>;
 		reg = <0xe1000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysclk: sysclk {
+			#clock-cells = <0>;
+			compatible = "fsl,qoriq-sysclk-2.0";
+			clock-output-names = "sysclk";
+		};
+
+		pll0: pll0@800 {
+			#clock-cells = <1>;
+			reg = <0x800 0x4>;
+			compatible = "fsl,qoriq-core-pll-2.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll0", "pll0-div2", "pll0-div4";
+		};
+
+		pll1: pll1@820 {
+			#clock-cells = <1>;
+			reg = <0x820 0x4>;
+			compatible = "fsl,qoriq-core-pll-2.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll1", "pll1-div2", "pll1-div4";
+		};
+
+		pll2: pll2@840 {
+			#clock-cells = <1>;
+			reg = <0x840 0x4>;
+			compatible = "fsl,qoriq-core-pll-2.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll2", "pll2-div2", "pll2-div4";
+		};
+
+		pll3: pll3@860 {
+			#clock-cells = <1>;
+			reg = <0x860 0x4>;
+			compatible = "fsl,qoriq-core-pll-2.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll3", "pll3-div2", "pll3-div4";
+		};
+
+		pll4: pll4@880 {
+			#clock-cells = <1>;
+			reg = <0x880 0x4>;
+			compatible = "fsl,qoriq-core-pll-2.0";
+			clocks = <&sysclk>;
+			clock-output-names = "pll4", "pll4-div2", "pll4-div4";
+		};
+
+		mux0: mux0@0 {
+			#clock-cells = <0>;
+			reg = <0x0 0x4>;
+			compatible = "fsl,qoriq-core-mux-2.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+				<&pll1 0>, <&pll1 1>, <&pll1 2>,
+				<&pll2 0>, <&pll2 1>, <&pll2 2>;
+			clock-names = "pll0", "pll0-div2", "pll0-div4",
+				"pll1", "pll1-div2", "pll1-div4",
+				"pll2", "pll2-div2", "pll2-div4";
+			clock-output-names = "cmux0";
+		};
+
+		mux1: mux1@20 {
+			#clock-cells = <0>;
+			reg = <0x20 0x4>;
+			compatible = "fsl,qoriq-core-mux-2.0";
+			clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+				<&pll1 0>, <&pll1 1>, <&pll1 2>,
+				<&pll2 0>, <&pll2 1>, <&pll2 2>;
+			clock-names = "pll0", "pll0-div2", "pll0-div4",
+				"pll1", "pll1-div2", "pll1-div4",
+				"pll2", "pll2-div2", "pll2-div4";
+			clock-output-names = "cmux1";
+		};
+
+		mux2: mux2@40 {
+			#clock-cells = <0>;
+			reg = <0x40 0x4>;
+			compatible = "fsl,qoriq-core-mux-2.0";
+			clocks = <&pll3 0>, <&pll3 1>, <&pll3 2>,
+				<&pll4 0>, <&pll4 1>, <&pll4 2>;
+			clock-names = "pll3", "pll3-div2", "pll3-div4",
+				"pll4", "pll4-div2", "pll4-div4";
+			clock-output-names = "cmux2";
+		};
 	};
 
 	rcpm: global-utilities@e2000 {

arch/powerpc/boot/dts/fsl/t4240si-pre.dtsi

@@ -67,61 +67,73 @@ cpus {
 		cpu0: PowerPC,e6500@0 {
 			device_type = "cpu";
 			reg = <0 1>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2_1>;
 		};
 		cpu1: PowerPC,e6500@2 {
 			device_type = "cpu";
 			reg = <2 3>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2_1>;
 		};
 		cpu2: PowerPC,e6500@4 {
 			device_type = "cpu";
 			reg = <4 5>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2_1>;
 		};
 		cpu3: PowerPC,e6500@6 {
 			device_type = "cpu";
 			reg = <6 7>;
+			clocks = <&mux0>;
 			next-level-cache = <&L2_1>;
 		};
 		cpu4: PowerPC,e6500@8 {
 			device_type = "cpu";
 			reg = <8 9>;
+			clocks = <&mux1>;
 			next-level-cache = <&L2_2>;
 		};
 		cpu5: PowerPC,e6500@10 {
 			device_type = "cpu";
 			reg = <10 11>;
+			clocks = <&mux1>;
 			next-level-cache = <&L2_2>;
 		};
 		cpu6: PowerPC,e6500@12 {
 			device_type = "cpu";
 			reg = <12 13>;
+			clocks = <&mux1>;
 			next-level-cache = <&L2_2>;
 		};
 		cpu7: PowerPC,e6500@14 {
 			device_type = "cpu";
 			reg = <14 15>;
+			clocks = <&mux1>;
 			next-level-cache = <&L2_2>;
 		};
 		cpu8: PowerPC,e6500@16 {
 			device_type = "cpu";
 			reg = <16 17>;
+			clocks = <&mux2>;
 			next-level-cache = <&L2_3>;
 		};
 		cpu9: PowerPC,e6500@18 {
 			device_type = "cpu";
 			reg = <18 19>;
+			clocks = <&mux2>;
 			next-level-cache = <&L2_3>;
 		};
 		cpu10: PowerPC,e6500@20 {
 			device_type = "cpu";
 			reg = <20 21>;
+			clocks = <&mux2>;
 			next-level-cache = <&L2_3>;
 		};
 		cpu11: PowerPC,e6500@22 {
 			device_type = "cpu";
 			reg = <22 23>;
+			clocks = <&mux2>;
 			next-level-cache = <&L2_3>;
 		};
 	};

arch/powerpc/boot/dts/t4240qds.dts

@@ -159,6 +159,48 @@ rtc@68 {
 						interrupts = <0x1 0x1 0 0>;
 					};
 				};
+
+				i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+
+					ina220@40 {
+						compatible = "ti,ina220";
+						reg = <0x40>;
+						shunt-resistor = <1000>;
+					};
+
+					ina220@41 {
+						compatible = "ti,ina220";
+						reg = <0x41>;
+						shunt-resistor = <1000>;
+					};
+
+					ina220@44 {
+						compatible = "ti,ina220";
+						reg = <0x44>;
+						shunt-resistor = <1000>;
+					};
+
+					ina220@45 {
+						compatible = "ti,ina220";
+						reg = <0x45>;
+						shunt-resistor = <1000>;
+					};
+
+					ina220@46 {
+						compatible = "ti,ina220";
+						reg = <0x46>;
+						shunt-resistor = <1000>;
+					};
+
+					ina220@47 {
+						compatible = "ti,ina220";
+						reg = <0x47>;
+						shunt-resistor = <1000>;
+					};
+				};
 			};
 		};
 

arch/powerpc/configs/corenet64_smp_defconfig

@@ -26,7 +26,6 @@ CONFIG_CORENET_GENERIC=y
 CONFIG_BINFMT_MISC=m
 CONFIG_MATH_EMULATION=y
 CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED=y
-CONFIG_FSL_IFC=y
 CONFIG_PCIEPORTBUS=y
 CONFIG_PCI_MSI=y
 CONFIG_RAPIDIO=y

arch/powerpc/configs/mpc85xx_defconfig

@@ -49,7 +49,6 @@ CONFIG_HIGHMEM=y
 CONFIG_BINFMT_MISC=m
 CONFIG_MATH_EMULATION=y
 CONFIG_FORCE_MAX_ZONEORDER=12
-CONFIG_FSL_IFC=y
 CONFIG_PCI=y
 CONFIG_PCI_MSI=y
 CONFIG_RAPIDIO=y

arch/powerpc/configs/mpc85xx_smp_defconfig

@@ -52,7 +52,6 @@ CONFIG_HIGHMEM=y
 CONFIG_BINFMT_MISC=m
 CONFIG_MATH_EMULATION=y
 CONFIG_FORCE_MAX_ZONEORDER=12
-CONFIG_FSL_IFC=y
 CONFIG_PCI=y
 CONFIG_PCI_MSI=y
 CONFIG_RAPIDIO=y

arch/powerpc/include/asm/exception-64e.h

@@ -46,9 +46,8 @@
 #define EX_CR		(1 * 8)
 #define EX_R10		(2 * 8)
 #define EX_R11		(3 * 8)
-#define EX_R13		(4 * 8)
-#define EX_R14		(5 * 8)
-#define EX_R15		(6 * 8)
+#define EX_R14		(4 * 8)
+#define EX_R15		(5 * 8)
 
 /*
  * The TLB miss exception uses different slots.
@@ -173,16 +172,6 @@ exc_##label##_book3e:
 	ld	r9,EX_TLB_R9(r12);					    \
 	ld	r8,EX_TLB_R8(r12);					    \
 	mtlr	r16;
-#define TLB_MISS_PROLOG_STATS_BOLTED						    \
-	mflr	r10;							    \
-	std	r8,PACA_EXTLB+EX_TLB_R8(r13);				    \
-	std	r9,PACA_EXTLB+EX_TLB_R9(r13);				    \
-	std	r10,PACA_EXTLB+EX_TLB_LR(r13);
-#define TLB_MISS_RESTORE_STATS_BOLTED					            \
-	ld	r16,PACA_EXTLB+EX_TLB_LR(r13);				    \
-	ld	r9,PACA_EXTLB+EX_TLB_R9(r13);				    \
-	ld	r8,PACA_EXTLB+EX_TLB_R8(r13);				    \
-	mtlr	r16;
 #define TLB_MISS_STATS_D(name)						    \
 	addi	r9,r13,MMSTAT_DSTATS+name;				    \
 	bl	.tlb_stat_inc;

arch/powerpc/include/asm/kvm_booke_hv_asm.h

@@ -36,26 +36,21 @@
  *   *(r8 + GPR11) = saved r11
  *
  * 64-bit host
- * Expected inputs (GEN/GDBELL/DBG/MC exception types):
+ * Expected inputs (GEN/GDBELL/DBG/CRIT/MC exception types):
  *  r10 = saved CR
  *  r13 = PACA_POINTER
  *  *(r13 + PACA_EX##type + EX_R10) = saved r10
  *  *(r13 + PACA_EX##type + EX_R11) = saved r11
  *  SPRN_SPRG_##type##_SCRATCH = saved r13
- *
-  * Expected inputs (CRIT exception type):
- *  r10 = saved CR
- *  r13 = PACA_POINTER
- *  *(r13 + PACA_EX##type + EX_R10) = saved r10
- *  *(r13 + PACA_EX##type + EX_R11) = saved r11
- *  *(r13 + PACA_EX##type + EX_R13) = saved r13
  *
  * Expected inputs (TLB exception type):
  *  r10 = saved CR
+ *  r12 = extlb pointer
  *  r13 = PACA_POINTER
- *  *(r13 + PACA_EX##type + EX_TLB_R10) = saved r10
- *  *(r13 + PACA_EX##type + EX_TLB_R11) = saved r11
- *  SPRN_SPRG_GEN_SCRATCH = saved r13
+ *  *(r12 + EX_TLB_R10) = saved r10
+ *  *(r12 + EX_TLB_R11) = saved r11
+ *  *(r12 + EX_TLB_R13) = saved r13
+ *  SPRN_SPRG_GEN_SCRATCH = saved r12
  *
  * Only the bolted version of TLB miss exception handlers is supported now.
  */

arch/powerpc/include/asm/mmu-book3e.h

@@ -287,11 +287,14 @@ extern int mmu_linear_psize;
 extern int mmu_vmemmap_psize;
 
 struct tlb_core_data {
+	/*
+	 * Per-core spinlock for e6500 TLB handlers (no tlbsrx.)
+	 * Must be the first struct element.
+	 */
+	u8 lock;
+
 	/* For software way selection, as on Freescale TLB1 */
 	u8 esel_next, esel_max, esel_first;
-
-	/* Per-core spinlock for e6500 TLB handlers (no tlbsrx.) */
-	u8 lock;
 };
 
 #ifdef CONFIG_PPC64

arch/powerpc/include/asm/paca.h

@@ -116,8 +116,11 @@ struct paca_struct {
 	/* Shared by all threads of a core -- points to tcd of first thread */
 	struct tlb_core_data *tcd_ptr;
 
-	/* We can have up to 3 levels of reentrancy in the TLB miss handler */
-	u64 extlb[3][EX_TLB_SIZE / sizeof(u64)];
+	/*
+	 * We can have up to 3 levels of reentrancy in the TLB miss handler,
+	 * in each of four exception levels (normal, crit, mcheck, debug).
+	 */
+	u64 extlb[12][EX_TLB_SIZE / sizeof(u64)];
 	u64 exmc[8];		/* used for machine checks */
 	u64 excrit[8];		/* used for crit interrupts */
 	u64 exdbg[8];		/* used for debug interrupts */
@@ -146,7 +149,7 @@ struct paca_struct {
 	u8 io_sync;			/* writel() needs spin_unlock sync */
 	u8 irq_work_pending;		/* IRQ_WORK interrupt while soft-disable */
 	u8 nap_state_lost;		/* NV GPR values lost in power7_idle */
-	u64 sprg3;			/* Saved user-visible sprg */
+	u64 sprg_vdso;			/* Saved user-visible sprg */
 #ifdef CONFIG_PPC_TRANSACTIONAL_MEM
 	u64 tm_scratch;                 /* TM scratch area for reclaim */
 #endif

arch/powerpc/include/asm/reg.h

@@ -577,9 +577,13 @@
 #define SPRN_SPRG3	0x113	/* Special Purpose Register General 3 */
 #define SPRN_USPRG3	0x103	/* SPRG3 userspace read */
 #define SPRN_SPRG4	0x114	/* Special Purpose Register General 4 */
+#define SPRN_USPRG4	0x104	/* SPRG4 userspace read */
 #define SPRN_SPRG5	0x115	/* Special Purpose Register General 5 */
+#define SPRN_USPRG5	0x105	/* SPRG5 userspace read */
 #define SPRN_SPRG6	0x116	/* Special Purpose Register General 6 */
+#define SPRN_USPRG6	0x106	/* SPRG6 userspace read */
 #define SPRN_SPRG7	0x117	/* Special Purpose Register General 7 */
+#define SPRN_USPRG7	0x107	/* SPRG7 userspace read */
 #define SPRN_SRR0	0x01A	/* Save/Restore Register 0 */
 #define SPRN_SRR1	0x01B	/* Save/Restore Register 1 */
 #define   SRR1_ISI_NOPT		0x40000000 /* ISI: Not found in hash */
@@ -882,11 +886,10 @@
  * 64-bit embedded
  *	- SPRG0 generic exception scratch
  *	- SPRG2 TLB exception stack
- *	- SPRG3 critical exception scratch and
- *        CPU and NUMA node for VDSO getcpu (user visible)
+ *	- SPRG3 critical exception scratch (user visible, sorry!)
  *	- SPRG4 unused (user visible)
  *	- SPRG6 TLB miss scratch (user visible, sorry !)
- *	- SPRG7 critical exception scratch
+ *	- SPRG7 CPU and NUMA node for VDSO getcpu (user visible)
  *	- SPRG8 machine check exception scratch
  *	- SPRG9 debug exception scratch
  *
@@ -943,6 +946,8 @@
 #define SPRN_SPRG_SCRATCH0	SPRN_SPRG2
 #define SPRN_SPRG_HPACA		SPRN_HSPRG0
 #define SPRN_SPRG_HSCRATCH0	SPRN_HSPRG1
+#define SPRN_SPRG_VDSO_READ	SPRN_USPRG3
+#define SPRN_SPRG_VDSO_WRITE	SPRN_SPRG3
 
 #define GET_PACA(rX)					\
 	BEGIN_FTR_SECTION_NESTED(66);			\
@@ -986,6 +991,8 @@
 #define SPRN_SPRG_TLB_SCRATCH	SPRN_SPRG6
 #define SPRN_SPRG_GEN_SCRATCH	SPRN_SPRG0
 #define SPRN_SPRG_GDBELL_SCRATCH SPRN_SPRG_GEN_SCRATCH
+#define SPRN_SPRG_VDSO_READ	SPRN_USPRG7
+#define SPRN_SPRG_VDSO_WRITE	SPRN_SPRG7
 
 #define SET_PACA(rX)	mtspr	SPRN_SPRG_PACA,rX
 #define GET_PACA(rX)	mfspr	rX,SPRN_SPRG_PACA
@@ -1105,6 +1112,8 @@
 #define PVR_8560	0x80200000
 #define PVR_VER_E500V1	0x8020
 #define PVR_VER_E500V2	0x8021
+#define PVR_VER_E500MC	0x8023
+#define PVR_VER_E5500	0x8024
 #define PVR_VER_E6500	0x8040
 
 /*

arch/powerpc/kernel/asm-offsets.c

@@ -253,7 +253,7 @@ int main(void)
 	DEFINE(PACA_SYSTEM_TIME, offsetof(struct paca_struct, system_time));
 	DEFINE(PACA_TRAP_SAVE, offsetof(struct paca_struct, trap_save));
 	DEFINE(PACA_NAPSTATELOST, offsetof(struct paca_struct, nap_state_lost));
-	DEFINE(PACA_SPRG3, offsetof(struct paca_struct, sprg3));
+	DEFINE(PACA_SPRG_VDSO, offsetof(struct paca_struct, sprg_vdso));
 #endif /* CONFIG_PPC64 */
 
 	/* RTAS */

arch/powerpc/kernel/setup_64.c

@@ -102,6 +102,8 @@ static void setup_tlb_core_data(void)
 {
 	int cpu;
 
+	BUILD_BUG_ON(offsetof(struct tlb_core_data, lock) != 0);
+
 	for_each_possible_cpu(cpu) {
 		int first = cpu_first_thread_sibling(cpu);
 
@@ -552,14 +554,20 @@ static void __init irqstack_early_init(void)
 static void __init exc_lvl_early_init(void)
 {
 	unsigned int i;
+	unsigned long sp;
 
 	for_each_possible_cpu(i) {
-		critirq_ctx[i] = (struct thread_info *)
-			__va(memblock_alloc(THREAD_SIZE, THREAD_SIZE));
-		dbgirq_ctx[i] = (struct thread_info *)
-			__va(memblock_alloc(THREAD_SIZE, THREAD_SIZE));
-		mcheckirq_ctx[i] = (struct thread_info *)
-			__va(memblock_alloc(THREAD_SIZE, THREAD_SIZE));
+		sp = memblock_alloc(THREAD_SIZE, THREAD_SIZE);
+		critirq_ctx[i] = (struct thread_info *)__va(sp);
+		paca[i].crit_kstack = __va(sp + THREAD_SIZE);
+
+		sp = memblock_alloc(THREAD_SIZE, THREAD_SIZE);
+		dbgirq_ctx[i] = (struct thread_info *)__va(sp);
+		paca[i].dbg_kstack = __va(sp + THREAD_SIZE);
+
+		sp = memblock_alloc(THREAD_SIZE, THREAD_SIZE);
+		mcheckirq_ctx[i] = (struct thread_info *)__va(sp);
+		paca[i].mc_kstack = __va(sp + THREAD_SIZE);
 	}
 
 	if (cpu_has_feature(CPU_FTR_DEBUG_LVL_EXC))

arch/powerpc/kernel/vdso.c

@@ -715,8 +715,8 @@ int vdso_getcpu_init(void)
 	unsigned long cpu, node, val;
 
 	/*
-	 * SPRG3 contains the CPU in the bottom 16 bits and the NUMA node in
-	 * the next 16 bits. The VDSO uses this to implement getcpu().
+	 * SPRG_VDSO contains the CPU in the bottom 16 bits and the NUMA node
+	 * in the next 16 bits.  The VDSO uses this to implement getcpu().
 	 */
 	cpu = get_cpu();
 	WARN_ON_ONCE(cpu > 0xffff);
@@ -725,8 +725,8 @@ int vdso_getcpu_init(void)
 	WARN_ON_ONCE(node > 0xffff);
 
 	val = (cpu & 0xfff) | ((node & 0xffff) << 16);
-	mtspr(SPRN_SPRG3, val);
-	get_paca()->sprg3 = val;
+	mtspr(SPRN_SPRG_VDSO_WRITE, val);
+	get_paca()->sprg_vdso = val;
 
 	put_cpu();
 

arch/powerpc/kernel/vdso32/getcpu.S

@@ -29,7 +29,7 @@
  */
 V_FUNCTION_BEGIN(__kernel_getcpu)
   .cfi_startproc
-	mfspr	r5,SPRN_USPRG3
+	mfspr	r5,SPRN_SPRG_VDSO_READ
 	cmpdi	cr0,r3,0
 	cmpdi	cr1,r4,0
 	clrlwi  r6,r5,16

arch/powerpc/kernel/vdso64/getcpu.S

@@ -29,7 +29,7 @@
  */
 V_FUNCTION_BEGIN(__kernel_getcpu)
   .cfi_startproc
-	mfspr	r5,SPRN_USPRG3
+	mfspr	r5,SPRN_SPRG_VDSO_READ
 	cmpdi	cr0,r3,0
 	cmpdi	cr1,r4,0
 	clrlwi  r6,r5,16

arch/powerpc/kvm/book3s_hv_rmhandlers.S

@@ -75,8 +75,8 @@ BEGIN_FTR_SECTION
 END_FTR_SECTION_IFCLR(CPU_FTR_ARCH_207S)
 
 	/* Restore SPRG3 */
-	ld	r3,PACA_SPRG3(r13)
-	mtspr	SPRN_SPRG3,r3
+	ld	r3,PACA_SPRG_VDSO(r13)
+	mtspr	SPRN_SPRG_VDSO_WRITE,r3
 
 	/* Reload the host's PMU registers */
 	ld	r3, PACALPPACAPTR(r13)	/* is the host using the PMU? */

arch/powerpc/kvm/book3s_interrupts.S

@@ -153,8 +153,8 @@ kvm_start_lightweight:
 	 * Reload kernel SPRG3 value.
 	 * No need to save guest value as usermode can't modify SPRG3.
 	 */
-	ld	r3, PACA_SPRG3(r13)
-	mtspr	SPRN_SPRG3, r3
+	ld	r3, PACA_SPRG_VDSO(r13)
+	mtspr	SPRN_SPRG_VDSO_WRITE, r3
 #endif /* CONFIG_PPC_BOOK3S_64 */
 
 	/* R7 = vcpu */

arch/powerpc/kvm/bookehv_interrupts.S

@@ -229,17 +229,20 @@
 	stw	r10, VCPU_CR(r4)
 	PPC_STL r11, VCPU_GPR(R4)(r4)
 	PPC_STL	r5, VCPU_GPR(R5)(r4)
-	.if \type == EX_CRIT
-	PPC_LL	r5, (\paca_ex + EX_R13)(r13)
-	.else
-	mfspr	r5, \scratch
-	.endif
 	PPC_STL	r6, VCPU_GPR(R6)(r4)
 	PPC_STL	r8, VCPU_GPR(R8)(r4)
 	PPC_STL	r9, VCPU_GPR(R9)(r4)
-	PPC_STL r5, VCPU_GPR(R13)(r4)
+	.if \type == EX_TLB
+	PPC_LL	r5, EX_TLB_R13(r12)
+	PPC_LL	r6, EX_TLB_R10(r12)
+	PPC_LL	r8, EX_TLB_R11(r12)
+	mfspr	r12, \scratch
+	.else
+	mfspr	r5, \scratch
 	PPC_LL	r6, (\paca_ex + \ex_r10)(r13)
 	PPC_LL	r8, (\paca_ex + \ex_r11)(r13)
+	.endif
+	PPC_STL r5, VCPU_GPR(R13)(r4)
 	PPC_STL r3, VCPU_GPR(R3)(r4)
 	PPC_STL r7, VCPU_GPR(R7)(r4)
 	PPC_STL r12, VCPU_GPR(R12)(r4)
@@ -435,10 +438,16 @@ _GLOBAL(kvmppc_resume_host)
 	PPC_STL	r5, VCPU_LR(r4)
 	mfspr	r7, SPRN_SPRG5
 	stw	r3, VCPU_VRSAVE(r4)
+#ifdef CONFIG_64BIT
+	PPC_LL	r3, PACA_SPRG_VDSO(r13)
+#endif
 	PPC_STD(r6, VCPU_SHARED_SPRG4, r11)
 	mfspr	r8, SPRN_SPRG6
 	PPC_STD(r7, VCPU_SHARED_SPRG5, r11)
 	mfspr	r9, SPRN_SPRG7
+#ifdef CONFIG_64BIT
+	mtspr	SPRN_SPRG_VDSO_WRITE, r3
+#endif
 	PPC_STD(r8, VCPU_SHARED_SPRG6, r11)
 	mfxer	r3
 	PPC_STD(r9, VCPU_SHARED_SPRG7, r11)

arch/powerpc/mm/tlb_low_64e.S

@@ -39,37 +39,49 @@
  *                                                                    *
  **********************************************************************/
 
+/*
+ * Note that, unlike non-bolted handlers, TLB_EXFRAME is not
+ * modified by the TLB miss handlers themselves, since the TLB miss
+ * handler code will not itself cause a recursive TLB miss.
+ *
+ * TLB_EXFRAME will be modified when crit/mc/debug exceptions are
+ * entered/exited.
+ */
 .macro tlb_prolog_bolted intnum addr
-	mtspr	SPRN_SPRG_GEN_SCRATCH,r13
+	mtspr	SPRN_SPRG_GEN_SCRATCH,r12
+	mfspr	r12,SPRN_SPRG_TLB_EXFRAME
+	std	r13,EX_TLB_R13(r12)
+	std	r10,EX_TLB_R10(r12)
 	mfspr	r13,SPRN_SPRG_PACA
-	std	r10,PACA_EXTLB+EX_TLB_R10(r13)
+
 	mfcr	r10
-	std	r11,PACA_EXTLB+EX_TLB_R11(r13)
+	std	r11,EX_TLB_R11(r12)
 #ifdef CONFIG_KVM_BOOKE_HV
 BEGIN_FTR_SECTION
 	mfspr	r11, SPRN_SRR1
 END_FTR_SECTION_IFSET(CPU_FTR_EMB_HV)
 #endif
 	DO_KVM	\intnum, SPRN_SRR1
-	std	r16,PACA_EXTLB+EX_TLB_R16(r13)
+	std	r16,EX_TLB_R16(r12)
 	mfspr	r16,\addr		/* get faulting address */
-	std	r14,PACA_EXTLB+EX_TLB_R14(r13)
+	std	r14,EX_TLB_R14(r12)
 	ld	r14,PACAPGD(r13)
-	std	r15,PACA_EXTLB+EX_TLB_R15(r13)
-	std	r10,PACA_EXTLB+EX_TLB_CR(r13)
-	TLB_MISS_PROLOG_STATS_BOLTED
+	std	r15,EX_TLB_R15(r12)
+	std	r10,EX_TLB_CR(r12)
+	TLB_MISS_PROLOG_STATS
 .endm
 
 .macro tlb_epilog_bolted
-	ld	r14,PACA_EXTLB+EX_TLB_CR(r13)
-	ld	r10,PACA_EXTLB+EX_TLB_R10(r13)
-	ld	r11,PACA_EXTLB+EX_TLB_R11(r13)
+	ld	r14,EX_TLB_CR(r12)
+	ld	r10,EX_TLB_R10(r12)
+	ld	r11,EX_TLB_R11(r12)
+	ld	r13,EX_TLB_R13(r12)
 	mtcr	r14
-	ld	r14,PACA_EXTLB+EX_TLB_R14(r13)
-	ld	r15,PACA_EXTLB+EX_TLB_R15(r13)
-	TLB_MISS_RESTORE_STATS_BOLTED
-	ld	r16,PACA_EXTLB+EX_TLB_R16(r13)
-	mfspr	r13,SPRN_SPRG_GEN_SCRATCH
+	ld	r14,EX_TLB_R14(r12)
+	ld	r15,EX_TLB_R15(r12)
+	TLB_MISS_RESTORE_STATS
+	ld	r16,EX_TLB_R16(r12)
+	mfspr	r12,SPRN_SPRG_GEN_SCRATCH
 .endm
 
 /* Data TLB miss */
@@ -284,7 +296,7 @@ itlb_miss_fault_bolted:
  * r14 = page table base
  * r13 = PACA
  * r11 = tlb_per_core ptr
- * r10 = crap (free to use)
+ * r10 = cpu number
  */
 tlb_miss_common_e6500:
 	/*
@@ -293,15 +305,18 @@ tlb_miss_common_e6500:
 	 *
 	 * MAS6:IND should be already set based on MAS4
 	 */
-	addi	r10,r11,TCD_LOCK
-1:	lbarx	r15,0,r10
+1:	lbarx	r15,0,r11
+	lhz	r10,PACAPACAINDEX(r13)
 	cmpdi	r15,0
+	cmpdi	cr1,r15,1	/* set cr1.eq = 0 for non-recursive */
 	bne	2f
-	li	r15,1
-	stbcx.	r15,0,r10
+	stbcx.	r10,0,r11
 	bne	1b
+3:
 	.subsection 1
-2:	lbz	r15,0(r10)
+2:	cmpd	cr1,r15,r10	/* recursive lock due to mcheck/crit/etc? */
+	beq	cr1,3b		/* unlock will happen if cr1.eq = 0 */
+	lbz	r15,0(r11)
 	cmpdi	r15,0
 	bne	2b
 	b	1b
@@ -379,9 +394,11 @@ tlb_miss_common_e6500:
 
 tlb_miss_done_e6500:
 	.macro	tlb_unlock_e6500
+	beq	cr1,1f		/* no unlock if lock was recursively grabbed */
 	li	r15,0
 	isync
-	stb	r15,TCD_LOCK(r11)
+	stb	r15,0(r11)
+1:
 	.endm
 
 	tlb_unlock_e6500

arch/powerpc/mm/tlb_nohash.c

@@ -144,6 +144,15 @@ int mmu_vmemmap_psize;		/* Page size used for the virtual mem map */
 int book3e_htw_mode;		/* HW tablewalk?  Value is PPC_HTW_* */
 unsigned long linear_map_top;	/* Top of linear mapping */
 
+
+/*
+ * Number of bytes to add to SPRN_SPRG_TLB_EXFRAME on crit/mcheck/debug
+ * exceptions.  This is used for bolted and e6500 TLB miss handlers which
+ * do not modify this SPRG in the TLB miss code; for other TLB miss handlers,
+ * this is set to zero.
+ */
+int extlb_level_exc;
+
 #endif /* CONFIG_PPC64 */
 
 #ifdef CONFIG_PPC_FSL_BOOK3E
@@ -559,6 +568,7 @@ static void setup_mmu_htw(void)
 		break;
 #ifdef CONFIG_PPC_FSL_BOOK3E
 	case PPC_HTW_E6500:
+		extlb_level_exc = EX_TLB_SIZE;
 		patch_exception(0x1c0, exc_data_tlb_miss_e6500_book3e);
 		patch_exception(0x1e0, exc_instruction_tlb_miss_e6500_book3e);
 		break;
@@ -652,6 +662,7 @@ static void __early_init_mmu(int boot_cpu)
 		memblock_enforce_memory_limit(linear_map_top);
 
 		if (book3e_htw_mode == PPC_HTW_NONE) {
+			extlb_level_exc = EX_TLB_SIZE;
 			patch_exception(0x1c0, exc_data_tlb_miss_bolted_book3e);
 			patch_exception(0x1e0,
 				exc_instruction_tlb_miss_bolted_book3e);

arch/powerpc/platforms/85xx/c293pcie.c

@@ -68,6 +68,7 @@ define_machine(c293_pcie) {
 	.init_IRQ		= c293_pcie_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/common.c

@@ -107,6 +107,12 @@ void __init mpc85xx_qe_init(void)
 	qe_reset();
 	of_node_put(np);
 
+}
+
+void __init mpc85xx_qe_par_io_init(void)
+{
+	struct device_node *np;
+
 	np = of_find_node_by_name(NULL, "par_io");
 	if (np) {
 		struct device_node *ucc;

arch/powerpc/platforms/85xx/corenet_generic.c

@@ -26,11 +26,13 @@
 #include <asm/udbg.h>
 #include <asm/mpic.h>
 #include <asm/ehv_pic.h>
+#include <asm/qe_ic.h>
 
 #include <linux/of_platform.h>
 #include <sysdev/fsl_soc.h>
 #include <sysdev/fsl_pci.h>
 #include "smp.h"
+#include "mpc85xx.h"
 
 void __init corenet_gen_pic_init(void)
 {
@@ -38,6 +40,8 @@ void __init corenet_gen_pic_init(void)
 	unsigned int flags = MPIC_BIG_ENDIAN | MPIC_SINGLE_DEST_CPU |
 		MPIC_NO_RESET;
 
+	struct device_node *np;
+
 	if (ppc_md.get_irq == mpic_get_coreint_irq)
 		flags |= MPIC_ENABLE_COREINT;
 
@@ -45,6 +49,13 @@ void __init corenet_gen_pic_init(void)
 	BUG_ON(mpic == NULL);
 
 	mpic_init(mpic);
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
+	if (np) {
+		qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
+				qe_ic_cascade_high_mpic);
+		of_node_put(np);
+	}
 }
 
 /*
@@ -57,6 +68,8 @@ void __init corenet_gen_setup_arch(void)
 	swiotlb_detect_4g();
 
 	pr_info("%s board from Freescale Semiconductor\n", ppc_md.name);
+
+	mpc85xx_qe_init();
 }
 
 static const struct of_device_id of_device_ids[] = {
@@ -81,6 +94,9 @@ static const struct of_device_id of_device_ids[] = {
 	{
 		.compatible	= "fsl,qoriq-pcie-v3.0",
 	},
+	{
+		.compatible	= "fsl,qe",
+	},
 	/* The following two are for the Freescale hypervisor */
 	{
 		.name		= "hypervisor",
@@ -163,6 +179,7 @@ define_machine(corenet_generic) {
 	.init_IRQ		= corenet_gen_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_coreint_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/ge_imp3a.c

@@ -215,6 +215,7 @@ define_machine(ge_imp3a) {
 	.show_cpuinfo		= ge_imp3a_show_cpuinfo,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/mpc8536_ds.c

@@ -76,6 +76,7 @@ define_machine(mpc8536_ds) {
 	.init_IRQ		= mpc8536_ds_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/mpc85xx.h

@@ -10,8 +10,10 @@ static inline void __init mpc85xx_cpm2_pic_init(void) {}
 
 #ifdef CONFIG_QUICC_ENGINE
 extern void mpc85xx_qe_init(void);
+extern void mpc85xx_qe_par_io_init(void);
 #else
 static inline void __init mpc85xx_qe_init(void) {}
+static inline void __init mpc85xx_qe_par_io_init(void) {}
 #endif
 
 #endif

arch/powerpc/platforms/85xx/mpc85xx_cds.c

@@ -385,6 +385,7 @@ define_machine(mpc85xx_cds) {
 #ifdef CONFIG_PCI
 	.restart	= mpc85xx_cds_restart,
 	.pcibios_fixup_bus	= mpc85xx_cds_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #else
 	.restart	= fsl_rstcr_restart,
 #endif

arch/powerpc/platforms/85xx/mpc85xx_ds.c

@@ -209,6 +209,7 @@ define_machine(mpc8544_ds) {
 	.init_IRQ		= mpc85xx_ds_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -223,6 +224,7 @@ define_machine(mpc8572_ds) {
 	.init_IRQ		= mpc85xx_ds_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -237,6 +239,7 @@ define_machine(p2020_ds) {
 	.init_IRQ		= mpc85xx_ds_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/mpc85xx_mds.c

@@ -239,6 +239,7 @@ static void __init mpc85xx_mds_qe_init(void)
 	struct device_node *np;
 
 	mpc85xx_qe_init();
+	mpc85xx_qe_par_io_init();
 	mpc85xx_mds_reset_ucc_phys();
 
 	if (machine_is(p1021_mds)) {
@@ -391,6 +392,7 @@ define_machine(mpc8568_mds) {
 	.progress	= udbg_progress,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 };
 
@@ -412,6 +414,7 @@ define_machine(mpc8569_mds) {
 	.progress	= udbg_progress,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 };
 
@@ -434,6 +437,7 @@ define_machine(p1021_mds) {
 	.progress	= udbg_progress,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 };
 

arch/powerpc/platforms/85xx/mpc85xx_rdb.c

@@ -86,10 +86,6 @@ void __init mpc85xx_rdb_pic_init(void)
  */
 static void __init mpc85xx_rdb_setup_arch(void)
 {
-#ifdef CONFIG_QUICC_ENGINE
-	struct device_node *np;
-#endif
-
 	if (ppc_md.progress)
 		ppc_md.progress("mpc85xx_rdb_setup_arch()", 0);
 
@@ -99,8 +95,10 @@ static void __init mpc85xx_rdb_setup_arch(void)
 
 #ifdef CONFIG_QUICC_ENGINE
 	mpc85xx_qe_init();
+	mpc85xx_qe_par_io_init();
 #if defined(CONFIG_UCC_GETH) || defined(CONFIG_SERIAL_QE)
 	if (machine_is(p1025_rdb)) {
+		struct device_node *np;
 
 		struct ccsr_guts __iomem *guts;
 
@@ -233,6 +231,7 @@ define_machine(p2020_rdb) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -247,6 +246,7 @@ define_machine(p1020_rdb) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -261,6 +261,7 @@ define_machine(p1021_rdb_pc) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -275,6 +276,7 @@ define_machine(p2020_rdb_pc) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -289,6 +291,7 @@ define_machine(p1025_rdb) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -303,6 +306,7 @@ define_machine(p1020_mbg_pc) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -317,6 +321,7 @@ define_machine(p1020_utm_pc) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -331,6 +336,7 @@ define_machine(p1020_rdb_pc) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -345,6 +351,7 @@ define_machine(p1020_rdb_pd) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -359,6 +366,7 @@ define_machine(p1024_rdb) {
 	.init_IRQ		= mpc85xx_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/p1010rdb.c

@@ -78,6 +78,7 @@ define_machine(p1010_rdb) {
 	.init_IRQ		= p1010_rdb_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/p1022_ds.c

@@ -567,6 +567,7 @@ define_machine(p1022_ds) {
 	.init_IRQ		= p1022_ds_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb	= fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/p1022_rdk.c

@@ -147,6 +147,7 @@ define_machine(p1022_rdk) {
 	.init_IRQ		= p1022_rdk_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/p1023_rds.c

@@ -126,6 +126,7 @@ define_machine(p1023_rds) {
 	.progress		= udbg_progress,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 };
 
@@ -140,5 +141,6 @@ define_machine(p1023_rdb) {
 	.progress		= udbg_progress,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 };

arch/powerpc/platforms/85xx/qemu_e500.c

@@ -66,6 +66,7 @@ define_machine(qemu_e500) {
 	.init_IRQ		= qemu_e500_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_coreint_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/85xx/sbc8548.c

@@ -135,6 +135,7 @@ define_machine(sbc8548) {
 	.restart	= fsl_rstcr_restart,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.calibrate_decr = generic_calibrate_decr,
 	.progress	= udbg_progress,

arch/powerpc/platforms/85xx/twr_p102x.c

@@ -77,6 +77,7 @@ static void __init twr_p1025_setup_arch(void)
 
 #ifdef CONFIG_QUICC_ENGINE
 	mpc85xx_qe_init();
+	mpc85xx_qe_par_io_init();
 
 #if defined(CONFIG_UCC_GETH) || defined(CONFIG_SERIAL_QE)
 	if (machine_is(twr_p1025)) {

arch/powerpc/platforms/85xx/xes_mpc85xx.c

@@ -170,6 +170,7 @@ define_machine(xes_mpc8572) {
 	.init_IRQ		= xes_mpc85xx_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -184,6 +185,7 @@ define_machine(xes_mpc8548) {
 	.init_IRQ		= xes_mpc85xx_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,
@@ -198,6 +200,7 @@ define_machine(xes_mpc8540) {
 	.init_IRQ		= xes_mpc85xx_pic_init,
 #ifdef CONFIG_PCI
 	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
 #endif
 	.get_irq		= mpic_get_irq,
 	.restart		= fsl_rstcr_restart,

arch/powerpc/platforms/embedded6xx/Kconfig

@@ -34,7 +34,6 @@ config MPC7448HPC2
 	select TSI108_BRIDGE
 	select DEFAULT_UIMAGE
 	select PPC_UDBG_16550
-	select TSI108_BRIDGE
 	help
 	  Select MPC7448HPC2 if configuring for Freescale MPC7448HPC2 (Taiga)
 	  platform
@@ -44,7 +43,6 @@ config PPC_HOLLY
 	depends on EMBEDDED6xx
 	select TSI108_BRIDGE
 	select PPC_UDBG_16550
-	select TSI108_BRIDGE
 	help
 	  Select PPC_HOLLY if configuring for an IBM 750GX/CL Eval
 	  Board with TSI108/9 bridge (Hickory/Holly)

arch/powerpc/sysdev/fsl_pci.c

@@ -22,10 +22,13 @@
 #include <linux/delay.h>
 #include <linux/string.h>
 #include <linux/init.h>
+#include <linux/interrupt.h>
 #include <linux/bootmem.h>
 #include <linux/memblock.h>
 #include <linux/log2.h>
 #include <linux/slab.h>
+#include <linux/suspend.h>
+#include <linux/syscore_ops.h>
 #include <linux/uaccess.h>
 
 #include <asm/io.h>
@@ -868,6 +871,14 @@ u64 fsl_pci_immrbar_base(struct pci_controller *hose)
 
 		pci_bus_read_config_dword(hose->bus,
 			PCI_DEVFN(0, 0), PCI_BASE_ADDRESS_0, &base);
+
+		/*
+		 * For PEXCSRBAR, bit 3-0 indicate prefetchable and
+		 * address type. So when getting base address, these
+		 * bits should be masked
+		 */
+		base &= PCI_BASE_ADDRESS_MEM_MASK;
+
 		return base;
 	}
 #endif
@@ -1086,55 +1097,171 @@ void fsl_pci_assign_primary(void)
 	}
 }
 
-static int fsl_pci_probe(struct platform_device *pdev)
+#ifdef CONFIG_PM_SLEEP
+static irqreturn_t fsl_pci_pme_handle(int irq, void *dev_id)
 {
-	int ret;
-	struct device_node *node;
+	struct pci_controller *hose = dev_id;
+	struct ccsr_pci __iomem *pci = hose->private_data;
+	u32 dr;
 
-	node = pdev->dev.of_node;
-	ret = fsl_add_bridge(pdev, fsl_pci_primary == node);
+	dr = in_be32(&pci->pex_pme_mes_dr);
+	if (!dr)
+		return IRQ_NONE;
 
-	mpc85xx_pci_err_probe(pdev);
+	out_be32(&pci->pex_pme_mes_dr, dr);
 
-	return 0;
+	return IRQ_HANDLED;
 }
 
-#ifdef CONFIG_PM
-static int fsl_pci_resume(struct device *dev)
+static int fsl_pci_pme_probe(struct pci_controller *hose)
 {
-	struct pci_controller *hose;
-	struct resource pci_rsrc;
+	struct ccsr_pci __iomem *pci;
+	struct pci_dev *dev;
+	int pme_irq;
+	int res;
+	u16 pms;
 
-	hose = pci_find_hose_for_OF_device(dev->of_node);
-	if (!hose)
-		return -ENODEV;
+	/* Get hose's pci_dev */
+	dev = list_first_entry(&hose->bus->devices, typeof(*dev), bus_list);
+
+	/* PME Disable */
+	pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pms);
+	pms &= ~PCI_PM_CTRL_PME_ENABLE;
+	pci_write_config_word(dev, dev->pm_cap + PCI_PM_CTRL, pms);
+
+	pme_irq = irq_of_parse_and_map(hose->dn, 0);
+	if (!pme_irq) {
+		dev_err(&dev->dev, "Failed to map PME interrupt.\n");
+
+		return -ENXIO;
+	}
+
+	res = devm_request_irq(hose->parent, pme_irq,
+			fsl_pci_pme_handle,
+			IRQF_SHARED,
+			"[PCI] PME", hose);
+	if (res < 0) {
+		dev_err(&dev->dev, "Unable to requiest irq %d for PME\n", pme_irq);
+		irq_dispose_mapping(pme_irq);
 
-	if (of_address_to_resource(dev->of_node, 0, &pci_rsrc)) {
-		dev_err(dev, "Get pci register base failed.");
 		return -ENODEV;
 	}
 
-	setup_pci_atmu(hose);
+	pci = hose->private_data;
+
+	/* Enable PTOD, ENL23D & EXL23D */
+	out_be32(&pci->pex_pme_mes_disr, 0);
+	setbits32(&pci->pex_pme_mes_disr,
+		  PME_DISR_EN_PTOD | PME_DISR_EN_ENL23D | PME_DISR_EN_EXL23D);
+
+	out_be32(&pci->pex_pme_mes_ier, 0);
+	setbits32(&pci->pex_pme_mes_ier,
+		  PME_DISR_EN_PTOD | PME_DISR_EN_ENL23D | PME_DISR_EN_EXL23D);
+
+	/* PME Enable */
+	pci_read_config_word(dev, dev->pm_cap + PCI_PM_CTRL, &pms);
+	pms |= PCI_PM_CTRL_PME_ENABLE;
+	pci_write_config_word(dev, dev->pm_cap + PCI_PM_CTRL, pms);
 
 	return 0;
 }
 
-static const struct dev_pm_ops pci_pm_ops = {
-	.resume = fsl_pci_resume,
-};
+static void send_pme_turnoff_message(struct pci_controller *hose)
+{
+	struct ccsr_pci __iomem *pci = hose->private_data;
+	u32 dr;
+	int i;
 
-#define PCI_PM_OPS (&pci_pm_ops)
+	/* Send PME_Turn_Off Message Request */
+	setbits32(&pci->pex_pmcr, PEX_PMCR_PTOMR);
 
-#else
+	/* Wait trun off done */
+	for (i = 0; i < 150; i++) {
+		dr = in_be32(&pci->pex_pme_mes_dr);
+		if (dr) {
+			out_be32(&pci->pex_pme_mes_dr, dr);
+			break;
+		}
+
+		udelay(1000);
+	}
+}
+
+static void fsl_pci_syscore_do_suspend(struct pci_controller *hose)
+{
+	send_pme_turnoff_message(hose);
+}
+
+static int fsl_pci_syscore_suspend(void)
+{
+	struct pci_controller *hose, *tmp;
 
-#define PCI_PM_OPS NULL
+	list_for_each_entry_safe(hose, tmp, &hose_list, list_node)
+		fsl_pci_syscore_do_suspend(hose);
 
+	return 0;
+}
+
+static void fsl_pci_syscore_do_resume(struct pci_controller *hose)
+{
+	struct ccsr_pci __iomem *pci = hose->private_data;
+	u32 dr;
+	int i;
+
+	/* Send Exit L2 State Message */
+	setbits32(&pci->pex_pmcr, PEX_PMCR_EXL2S);
+
+	/* Wait exit done */
+	for (i = 0; i < 150; i++) {
+		dr = in_be32(&pci->pex_pme_mes_dr);
+		if (dr) {
+			out_be32(&pci->pex_pme_mes_dr, dr);
+			break;
+		}
+
+		udelay(1000);
+	}
+
+	setup_pci_atmu(hose);
+}
+
+static void fsl_pci_syscore_resume(void)
+{
+	struct pci_controller *hose, *tmp;
+
+	list_for_each_entry_safe(hose, tmp, &hose_list, list_node)
+		fsl_pci_syscore_do_resume(hose);
+}
+
+static struct syscore_ops pci_syscore_pm_ops = {
+	.suspend = fsl_pci_syscore_suspend,
+	.resume = fsl_pci_syscore_resume,
+};
 #endif
 
+void fsl_pcibios_fixup_phb(struct pci_controller *phb)
+{
+#ifdef CONFIG_PM_SLEEP
+	fsl_pci_pme_probe(phb);
+#endif
+}
+
+static int fsl_pci_probe(struct platform_device *pdev)
+{
+	struct device_node *node;
+	int ret;
+
+	node = pdev->dev.of_node;
+	ret = fsl_add_bridge(pdev, fsl_pci_primary == node);
+
+	mpc85xx_pci_err_probe(pdev);
+
+	return 0;
+}
+
 static struct platform_driver fsl_pci_driver = {
 	.driver = {
 		.name = "fsl-pci",
-		.pm = PCI_PM_OPS,
 		.of_match_table = pci_ids,
 	},
 	.probe = fsl_pci_probe,
@@ -1142,6 +1269,9 @@ static struct platform_driver fsl_pci_driver = {
 
 static int __init fsl_pci_init(void)
 {
+#ifdef CONFIG_PM_SLEEP
+	register_syscore_ops(&pci_syscore_pm_ops);
+#endif
 	return platform_driver_register(&fsl_pci_driver);
 }
 arch_initcall(fsl_pci_init);

arch/powerpc/sysdev/fsl_pci.h

@@ -32,6 +32,13 @@ struct platform_device;
 #define PIWAR_WRITE_SNOOP	0x00005000
 #define PIWAR_SZ_MASK          0x0000003f
 
+#define PEX_PMCR_PTOMR		0x1
+#define PEX_PMCR_EXL2S		0x2
+
+#define PME_DISR_EN_PTOD	0x00008000
+#define PME_DISR_EN_ENL23D	0x00002000
+#define PME_DISR_EN_EXL23D	0x00001000
+
 /* PCI/PCI Express outbound window reg */
 struct pci_outbound_window_regs {
 	__be32	potar;	/* 0x.0 - Outbound translation address register */
@@ -111,6 +118,7 @@ struct ccsr_pci {
 
 extern int fsl_add_bridge(struct platform_device *pdev, int is_primary);
 extern void fsl_pcibios_fixup_bus(struct pci_bus *bus);
+extern void fsl_pcibios_fixup_phb(struct pci_controller *phb);
 extern int mpc83xx_add_bridge(struct device_node *dev);
 u64 fsl_pci_immrbar_base(struct pci_controller *hose);
 

drivers/watchdog/booke_wdt.c

@@ -138,14 +138,6 @@ static void __booke_wdt_enable(void *data)
 	val &= ~WDTP_MASK;
 	val |= (TCR_WIE|TCR_WRC(WRC_CHIP)|WDTP(booke_wdt_period));
 
-#ifdef CONFIG_PPC_BOOK3E_64
-	/*
-	 * Crit ints are currently broken on PPC64 Book-E, so
-	 * just disable them for now.
-	 */
-	val &= ~TCR_WIE;
-#endif
-
 	mtspr(SPRN_TCR, val);
 }