Merge branch 'remotes/lorenzo/pci/uniphier'

  - Add UniPhier PCIe controller driver and DT bindings (Kunihiko Hayashi)

* remotes/lorenzo/pci/uniphier:
  PCI: uniphier: Add UniPhier PCIe host controller support
  dt-bindings: PCI: Add UniPhier PCIe host controller description

# Conflicts:
#	drivers/pci/controller/dwc/Kconfig
#	drivers/pci/controller/dwc/Makefile

Documentation/devicetree/bindings/pci/uniphier-pcie.txt

+Socionext UniPhier PCIe host controller bindings
+
+This describes the devicetree bindings for PCIe host controller implemented
+on Socionext UniPhier SoCs.
+
+UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core.
+It shares common functions with the PCIe DesignWare core driver and inherits
+common properties defined in
+Documentation/devicetree/bindings/pci/designware-pcie.txt.
+
+Required properties:
+- compatible: Should be "socionext,uniphier-pcie".
+- reg: Specifies offset and length of the register set for the device.
+	According to the reg-names, appropriate register sets are required.
+- reg-names: Must include the following entries:
+    "dbi"    - controller configuration registers
+    "link"   - SoC-specific glue layer registers
+    "config" - PCIe configuration space
+- clocks: A phandle to the clock gate for PCIe glue layer including
+	the host controller.
+- resets: A phandle to the reset line for PCIe glue layer including
+	the host controller.
+- interrupts: A list of interrupt specifiers. According to the
+	interrupt-names, appropriate interrupts are required.
+- interrupt-names: Must include the following entries:
+    "dma" - DMA interrupt
+    "msi" - MSI interrupt
+
+Optional properties:
+- phys: A phandle to generic PCIe PHY. According to the phy-names, appropriate
+	phys are required.
+- phy-names: Must be "pcie-phy".
+
+Required sub-node:
+- legacy-interrupt-controller: Specifies interrupt controller for legacy PCI
+	interrupts.
+
+Required properties for legacy-interrupt-controller:
+- interrupt-controller: identifies the node as an interrupt controller.
+- #interrupt-cells: specifies the number of cells needed to encode an
+	interrupt source. The value must be 1.
+- interrupt-parent: Phandle to the parent interrupt controller.
+- interrupts: An interrupt specifier for legacy interrupt.
+
+Example:
+
+	pcie: pcie@66000000 {
+		compatible = "socionext,uniphier-pcie", "snps,dw-pcie";
+		status = "disabled";
+		reg-names = "dbi", "link", "config";
+		reg = <0x66000000 0x1000>, <0x66010000 0x10000>,
+		      <0x2fff0000 0x10000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		clocks = <&sys_clk 24>;
+		resets = <&sys_rst 24>;
+		num-lanes = <1>;
+		num-viewport = <1>;
+		bus-range = <0x0 0xff>;
+		device_type = "pci";
+		ranges =
+		/* downstream I/O */
+			<0x81000000 0 0x00000000  0x2ffe0000  0 0x00010000
+		/* non-prefetchable memory */
+			 0x82000000 0 0x00000000  0x20000000  0 0x0ffe0000>;
+		#interrupt-cells = <1>;
+		interrupt-names = "dma", "msi";
+		interrupts = <0 224 4>, <0 225 4>;
+		interrupt-map-mask = <0 0 0  7>;
+		interrupt-map = <0 0 0  1  &pcie_intc 0>,	/* INTA */
+				<0 0 0  2  &pcie_intc 1>,	/* INTB */
+				<0 0 0  3  &pcie_intc 2>,	/* INTC */
+				<0 0 0  4  &pcie_intc 3>;	/* INTD */
+
+		pcie_intc: legacy-interrupt-controller {
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <0 226 4>;
+		};
+	};

MAINTAINERS

@@ -11585,6 +11585,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt
 F:	drivers/pci/controller/pci-v3-semi.c
 
+PCIE DRIVER FOR SOCIONEXT UNIPHIER
+M:	Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+L:	linux-pci@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/pci/uniphier-pcie.txt
+F:	drivers/pci/controller/dwc/pcie-uniphier.c
+
 PCIE DRIVER FOR ST SPEAR13XX
 M:	Pratyush Anand <pratyush.anand@gmail.com>
 L:	linux-pci@vger.kernel.org

drivers/pci/controller/dwc/Kconfig

@@ -203,4 +203,14 @@ config PCI_MESON
 	  and therefore the driver re-uses the DesignWare core functions to
 	  implement the driver.
 
+config PCIE_UNIPHIER
+	bool "Socionext UniPhier PCIe controllers"
+	depends on ARCH_UNIPHIER || COMPILE_TEST
+	depends on OF && HAS_IOMEM
+	depends on PCI_MSI_IRQ_DOMAIN
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want PCIe controller support on UniPhier SoCs.
+	  This driver supports LD20 and PXs3 SoCs.
+
 endmenu

drivers/pci/controller/dwc/Makefile

@@ -15,6 +15,7 @@ obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
 obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o
 obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
 obj-$(CONFIG_PCI_MESON) += pci-meson.o
+obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o
 
 # The following drivers are for devices that use the generic ACPI
 # pci_root.c driver but don't support standard ECAM config access.