Merge tag 'v4.1-rockchip-dts1' of...

Merge tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "ARM: rockchip: dts changes for 4.1" from Heiko Stuebner:

This adds and enables the usbphy nodes on the rk3288 boards and enables
the gmac on the firefly board. A new board the Popmetal-rk3288 is also
added. And finally the pmic supplies for act8846 based boards are added,
as the act8865/act8846 driver gained supply handling in the regulator tree.

* tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: complete rk3288-evb pmic supplies
  ARM: dts: rockchip: add input supplies for the act8846 on Radxa Rock
  ARM: dts: add rk3288 PopMetal board
  dt-bindings: add root compatible property for PopMetal board
  ARM: dts: rockchip: enable gmac on rk3288-firefly
  ARM: dts: rockchip: enable usbphy on rk3288-firefly
  ARM: dts: rockchip: Enable usb PHY on rk3288-evb board
  ARM: dts: rockchip: add rk3288 usb PHY
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/arm/rockchip.txt

@@ -22,3 +22,7 @@ Rockchip platforms device tree bindings
       - compatible = "firefly,firefly-rk3288", "rockchip,rk3288";
     or
       - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288";
+
+- ChipSPARK PopMetal-RK3288 board:
+    Required root node properties:
+      - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";

arch/arm/boot/dts/rk3188-radxarock.dts

@@ -103,6 +103,14 @@ vcc_host: usb-host-regulator {
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	vsys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vsys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
 };
 
 &emac {
@@ -148,6 +156,14 @@ act8846: act8846@5a {
 		pinctrl-names = "default";
 		pinctrl-0 = <&act8846_dvs0_ctl>;
 
+		vp1-supply = <&vsys>;
+		vp2-supply = <&vsys>;
+		vp3-supply = <&vsys>;
+		vp4-supply = <&vsys>;
+		inl1-supply = <&vcc_io>;
+		inl2-supply = <&vsys>;
+		inl3-supply = <&vsys>;
+
 		regulators {
 			vcc_ddr: REG1 {
 				regulator-name = "VCC_DDR";

arch/arm/boot/dts/rk3288-evb-act8846.dts

@@ -33,6 +33,7 @@ vdd_cpu: syr827@40 {
 		regulator-max-microvolt = <1350000>;
 		regulator-always-on;
 		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
 	};
 
 	vdd_gpu: syr828@41 {
@@ -43,6 +44,7 @@ vdd_gpu: syr828@41 {
 		regulator-min-microvolt = <850000>;
 		regulator-max-microvolt = <1350000>;
 		regulator-always-on;
+		vin-supply = <&vcc_sys>;
 	};
 
 	hym8563@51 {
@@ -64,6 +66,14 @@ act8846: act8846@5a {
 		reg = <0x5a>;
 		status = "okay";
 
+		vp1-supply = <&vcc_sys>;
+		vp2-supply = <&vcc_sys>;
+		vp3-supply = <&vcc_sys>;
+		vp4-supply = <&vcc_sys>;
+		inl1-supply = <&vcc_io>;
+		inl2-supply = <&vcc_sys>;
+		inl3-supply = <&vcc_20>;
+
 		regulators {
 			vcc_ddr: REG1 {
 				regulator-name = "VCC_DDR";

arch/arm/boot/dts/rk3288-evb-rk808.dts

@@ -43,9 +43,16 @@ rk808: pmic@1b {
 		#clock-cells = <1>;
 		clock-output-names = "xin32k", "rk808-clkout2";
 
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
 		vcc8-supply = <&vcc_18>;
 		vcc9-supply = <&vcc_io>;
 		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_sys>;
 		vcc12-supply = <&vcc_io>;
 		vddio-supply = <&vccio_pmu>;
 

arch/arm/boot/dts/rk3288-evb.dtsi

@@ -103,6 +103,15 @@ vcc_phy: vcc-phy-regulator {
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &emmc {
@@ -238,6 +247,10 @@ eth_phy_pwr: eth-phy-pwr {
 	};
 };
 
+&usbphy {
+	status = "okay";
+};
+
 &usb_host0_ehci {
 	status = "okay";
 };

arch/arm/boot/dts/rk3288-firefly.dtsi

@@ -179,6 +179,22 @@ &emmc {
 	status = "okay";
 };
 
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>;
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
 &hdmi {
 	ddc-i2c-bus = <&i2c5>;
 	status = "okay";
@@ -459,6 +475,10 @@ &uart3 {
 	status = "okay";
 };
 
+&usbphy {
+	status = "okay";
+};
+
 &usb_host1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&usbhub_rst>;

arch/arm/boot/dts/rk3288-popmetal.dts

+/*
+ * Copyright (c) 2014, 2015 Andy Yan <andy.yan@rock-chips.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *  Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "rk3288.dtsi"
+
+/ {
+	model = "PopMetal-RK3288";
+	compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
+
+	memory{
+		reg = <0 0x80000000>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		button@0 {
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			linux,code = <116>;
+			label = "GPIO Key Power";
+			linux,input-type = <1>;
+			gpio-key,wakeup = <1>;
+			debounce-interval = <100>;
+		};
+	};
+
+	ir: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_int>;
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	broken-cd;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;                     /* wp not hooked up */
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&gmac {
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_18>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_sys>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-name = "vdd_arm";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_lan: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_lan";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vccio_sd: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			ldo5: LDO_REG5 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "ldo5";
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca_codec: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_codec";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_wl: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_wl";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_lcd: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ak8963: ak8963@0d {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&comp_int>;
+	};
+
+	l3g4200d: l3g4200d@68 {
+		compatible = "st,l3g4200d-gyro";
+		st,drdy-int-pin = <2>;
+		reg = <0x6b>;
+	};
+
+	mma8452: mma8452@1d {
+		compatible = "fsl,mma8452";
+		reg = <0x1d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gsensor_int>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	ak8963 {
+		comp_int: comp-int {
+			rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	ir {
+		ir_int: ir-int {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	mma8452 {
+		gsensor_int: gsensor-int {
+			rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};

arch/arm/boot/dts/rk3288.dtsi

@@ -419,6 +419,8 @@ usb_host0_ehci: usb@ff500000 {
 		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_USBHOST0>;
 		clock-names = "usbhost";
+		phys = <&usbphy1>;
+		phy-names = "usb";
 		status = "disabled";
 	};
 
@@ -431,6 +433,8 @@ usb_host1: usb@ff540000 {
 		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_USBHOST1>;
 		clock-names = "otg";
+		phys = <&usbphy2>;
+		phy-names = "usb2-phy";
 		status = "disabled";
 	};
 
@@ -441,6 +445,8 @@ usb_otg: usb@ff580000 {
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_OTG0>;
 		clock-names = "otg";
+		phys = <&usbphy0>;
+		phy-names = "usb2-phy";
 		status = "disabled";
 	};
 
@@ -697,6 +703,35 @@ gic: interrupt-controller@ffc01000 {
 		interrupts = <GIC_PPI 9 0xf04>;
 	};
 
+	usbphy: phy {
+		compatible = "rockchip,rk3288-usb-phy";
+		rockchip,grf = <&grf>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		usbphy0: usb-phy0 {
+			#phy-cells = <0>;
+			reg = <0x320>;
+			clocks = <&cru SCLK_OTGPHY0>;
+			clock-names = "phyclk";
+		};
+
+		usbphy1: usb-phy1 {
+			#phy-cells = <0>;
+			reg = <0x334>;
+			clocks = <&cru SCLK_OTGPHY1>;
+			clock-names = "phyclk";
+		};
+
+		usbphy2: usb-phy2 {
+			#phy-cells = <0>;
+			reg = <0x348>;
+			clocks = <&cru SCLK_OTGPHY2>;
+			clock-names = "phyclk";
+		};
+	};
+
 	pinctrl: pinctrl {
 		compatible = "rockchip,rk3288-pinctrl";
 		rockchip,grf = <&grf>;