Commit d0ad5e89 authored by Mark Brown's avatar Mark Brown Committed by Grant Likely

gpio: Add decode of WM8994 GPIO configuration

For the human reader.
Signed-off-by: default avatarMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarGrant Likely <grant.likely@secretlab.ca>
parent 6f61415e
......@@ -117,6 +117,60 @@ static int wm8994_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
#ifdef CONFIG_DEBUG_FS
static const char *wm8994_gpio_fn(u16 fn)
{
switch (fn) {
case WM8994_GP_FN_PIN_SPECIFIC:
return "pin-specific";
case WM8994_GP_FN_GPIO:
return "GPIO";
case WM8994_GP_FN_SDOUT:
return "SDOUT";
case WM8994_GP_FN_IRQ:
return "IRQ";
case WM8994_GP_FN_TEMPERATURE:
return "Temperature";
case WM8994_GP_FN_MICBIAS1_DET:
return "MICBIAS1 detect";
case WM8994_GP_FN_MICBIAS1_SHORT:
return "MICBIAS1 short";
case WM8994_GP_FN_MICBIAS2_DET:
return "MICBIAS2 detect";
case WM8994_GP_FN_MICBIAS2_SHORT:
return "MICBIAS2 short";
case WM8994_GP_FN_FLL1_LOCK:
return "FLL1 lock";
case WM8994_GP_FN_FLL2_LOCK:
return "FLL2 lock";
case WM8994_GP_FN_SRC1_LOCK:
return "SRC1 lock";
case WM8994_GP_FN_SRC2_LOCK:
return "SRC2 lock";
case WM8994_GP_FN_DRC1_ACT:
return "DRC1 activity";
case WM8994_GP_FN_DRC2_ACT:
return "DRC2 activity";
case WM8994_GP_FN_DRC3_ACT:
return "DRC3 activity";
case WM8994_GP_FN_WSEQ_STATUS:
return "Write sequencer";
case WM8994_GP_FN_FIFO_ERROR:
return "FIFO error";
case WM8994_GP_FN_OPCLK:
return "OPCLK";
case WM8994_GP_FN_THW:
return "Thermal warning";
case WM8994_GP_FN_DCS_DONE:
return "DC servo";
case WM8994_GP_FN_FLL1_OUT:
return "FLL1 output";
case WM8994_GP_FN_FLL2_OUT:
return "FLL1 output";
default:
return "Unknown";
}
}
static void wm8994_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
{
struct wm8994_gpio *wm8994_gpio = to_wm8994_gpio(chip);
......@@ -148,8 +202,29 @@ static void wm8994_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
continue;
}
/* No decode yet; note that GPIO2 is special */
seq_printf(s, "(%x)\n", reg);
if (reg & WM8994_GPN_DIR)
seq_printf(s, "in ");
else
seq_printf(s, "out ");
if (reg & WM8994_GPN_PU)
seq_printf(s, "pull up ");
if (reg & WM8994_GPN_PD)
seq_printf(s, "pull down ");
if (reg & WM8994_GPN_POL)
seq_printf(s, "inverted ");
else
seq_printf(s, "noninverted ");
if (reg & WM8994_GPN_OP_CFG)
seq_printf(s, "open drain ");
else
seq_printf(s, "CMOS ");
seq_printf(s, "%s (%x)\n",
wm8994_gpio_fn(reg & WM8994_GPN_FN_MASK), reg);
}
}
#else
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment