arm64: dts: imx8mm-evk: Adjust i2c nodes following alphabetical sort

The iomuxc node is being put at end of file because of its huge
pinctrl data. I2C devices should be placed in alphabetical sort.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arch/arm64/boot/dts/freescale/imx8mm-evk.dts

@@ -94,68 +94,6 @@ ethphy0: ethernet-phy@0 {
 	};
 };
 
-&sai3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_sai3>;
-	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
-	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
-	assigned-clock-rates = <24576000>;
-	status = "okay";
-};
-
-&snvs_pwrkey {
-	status = "okay";
-};
-
-&uart2 { /* console */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&usbotg1 {
-	dr_mode = "otg";
-	hnp-disable;
-	srp-disable;
-	adp-disable;
-	usb-role-switch;
-	status = "okay";
-
-	port {
-		usb1_drd_sw: endpoint {
-			remote-endpoint = <&typec1_dr_sw>;
-		};
-	};
-};
-
-&usdhc2 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
-	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
-	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
-	cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	vmmc-supply = <&reg_usdhc2_vmmc>;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
-	bus-width = <8>;
-	non-removable;
-	status = "okay";
-};
-
-&wdog1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdog>;
-	fsl,ext-reset-output;
-	status = "okay";
-};
-
 &i2c1 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -306,6 +244,68 @@ typec1_con: connector {
 	};
 };
 
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart2 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		usb1_drd_sw: endpoint {
+			remote-endpoint = <&typec1_dr_sw>;
+		};
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
 &iomuxc {
 	pinctrl-names = "default";