Commit d13501a2 authored by Katsuhiro Suzuki's avatar Katsuhiro Suzuki Committed by Stephen Boyd

clk: fractional-divider: check parent rate only if flag is set

Custom approximation of fractional-divider may not need parent clock
rate checking. For example Rockchip SoCs work fine using grand parent
clock rate even if target rate is greater than parent.

This patch checks parent clock rate only if CLK_SET_RATE_PARENT flag
is set.

For detailed example, clock tree of Rockchip I2S audio hardware.
  - Clock rate of CPLL is 1.2GHz, GPLL is 491.52MHz.
  - i2s1_div is integer divider can divide N (N is 1~128).
    Input clock is CPLL or GPLL. Initial divider value is N = 1.
    Ex) PLL = CPLL, N = 10, i2s1_div output rate is
      CPLL / 10 = 1.2GHz / 10 = 120MHz
  - i2s1_frac is fractional divider can divide input to x/y, x and
    y are 16bit integer.

CPLL --> | selector | ---> i2s1_div -+--> | selector | --> I2S1 MCLK
GPLL --> |          | ,--------------'    |          |
                      `--> i2s1_frac ---> |          |

Clock mux system try to choose suitable one from i2s1_div and
i2s1_frac for master clock (MCLK) of I2S1.

Bad scenario as follows:
  - Try to set MCLK to 8.192MHz (32kHz audio replay)
    Candidate setting is
    - i2s1_div: GPLL / 60 = 8.192MHz
    i2s1_div candidate is exactly same as target clock rate, so mux
    choose this clock source. i2s1_div output rate is changed
    491.52MHz -> 8.192MHz

  - After that try to set to 11.2896MHz (44.1kHz audio replay)
    Candidate settings are
    - i2s1_div : CPLL / 107 = 11.214945MHz
    - i2s1_frac: i2s1_div   = 8.192MHz
      This is because clk_fd_round_rate() thinks target rate
      (11.2896MHz) is higher than parent rate (i2s1_div = 8.192MHz)
      and returns parent clock rate.

Above is current upstreamed behavior. Clock mux system choose
i2s1_div, but this clock rate is not acceptable for I2S driver, so
users cannot replay audio.

Expected behavior is:
  - Try to set master clock to 11.2896MHz (44.1kHz audio replay)
    Candidate settings are
    - i2s1_div : CPLL / 107          = 11.214945MHz
    - i2s1_frac: i2s1_div * 147/6400 = 11.2896MHz
                 Change i2s1_div to GPLL / 1 = 491.52MHz at same
                 time.

If apply this commit, clk_fd_round_rate() calls custom approximate
function of Rockchip even if target rate is higher than parent.
Custom function changes both grand parent (i2s1_div) and parent
(i2s_frac) settings at same time. Clock mux system can choose
i2s1_frac and audio works fine.
Signed-off-by: default avatarKatsuhiro Suzuki <katsuhiro@katsuster.net>
Reviewed-by: default avatarHeiko Stuebner <heiko@sntech.de>
[sboyd@kernel.org: Make function into a macro instead]
Signed-off-by: default avatarStephen Boyd <sboyd@kernel.org>
parent bfeffd15
......@@ -79,7 +79,7 @@ static long clk_fd_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long m, n;
u64 ret;
if (!rate || rate >= *parent_rate)
if (!rate || (!clk_hw_can_set_rate_parent(hw) && rate >= *parent_rate))
return *parent_rate;
if (fd->approximation)
......
......@@ -792,6 +792,9 @@ unsigned int __clk_get_enable_count(struct clk *clk);
unsigned long clk_hw_get_rate(const struct clk_hw *hw);
unsigned long __clk_get_flags(struct clk *clk);
unsigned long clk_hw_get_flags(const struct clk_hw *hw);
#define clk_hw_can_set_rate_parent(hw) \
(clk_hw_get_flags((hw)) & CLK_SET_RATE_PARENT)
bool clk_hw_is_prepared(const struct clk_hw *hw);
bool clk_hw_rate_is_protected(const struct clk_hw *hw);
bool clk_hw_is_enabled(const struct clk_hw *hw);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment