ARM: dts: mmp2-olpc-xo-1-75: Enable audio support

This enables the audio SRAM, DMA engine, I2S interface, and codec, hooks
them together and adds a audio-graph-card instance.

It also removes the jack gpios from the gpio-keys instance, because the
audio jack driver registers an input device.

Link: https://lore.kernel.org/r/20200718205019.184927-10-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts

@@ -57,24 +57,6 @@ tablet_mode {
 			linux,code = <SW_TABLET_MODE>;
 			wakeup-source;
 		};
-
-		microphone_insert {
-			label = "Microphone Plug";
-			gpios = <&gpio 96 GPIO_ACTIVE_HIGH>;
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_MICROPHONE_INSERT>;
-			debounce-interval = <100>;
-			wakeup-source;
-		};
-
-		headphone_insert {
-			label = "Headphone Plug";
-			gpios = <&gpio 97 GPIO_ACTIVE_HIGH>;
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_HEADPHONE_INSERT>;
-			debounce-interval = <100>;
-			wakeup-source;
-		};
 	};
 
 	i2c {
@@ -123,6 +105,18 @@ wlan_pwrseq: pwrseq0 {
 		reset-gpios = <&gpio 58 GPIO_ACTIVE_HIGH>;
 	};
 
+	sound-card {
+		compatible = "audio-graph-card";
+		label = "OLPC XO";
+		dais = <&sspa0_dai>;
+		routing = "Headphones", "HPOL",
+			  "Headphones", "HPOR",
+			  "MIC2", "Mic Jack";
+		widgets = "Headphone", "Headphones", "Microphone", "Mic Jack";
+		hp-det-gpio = <&gpio 97 GPIO_ACTIVE_HIGH>;
+		mic-det-gpio = <&gpio 96 GPIO_ACTIVE_HIGH>;
+	};
+
 	soc {
 		axi@d4200000 {
 			ap-sp@d4290000 {
@@ -197,6 +191,14 @@ audio-codec@1a {
 		compatible = "realtek,alc5631";
 		reg = <0x1a>;
 		status = "okay";
+
+		port {
+			rt5631_0: endpoint {
+				mclk-fs = <256>;
+				clocks = <&audio_clk 0>;
+				remote-endpoint = <&sspa0_0>;
+			};
+		};
 	};
 };
 
@@ -243,3 +245,30 @@ camera0_0: endpoint {
 		};
 	};
 };
+
+&asram {
+	status = "okay";
+};
+
+&adma0 {
+	status = "okay";
+};
+
+&audio_clk {
+	status = "okay";
+};
+
+&sspa0 {
+	status = "okay";
+	dmas = <&adma0 0>, <&adma0 1>;
+	dma-names = "tx", "rx";
+
+	sspa0_dai: port {
+		sspa0_0: endpoint {
+			remote-endpoint = <&rt5631_0>;
+			frame-master;
+			bitclock-master;
+			dai-format = "i2s";
+		};
+	};
+};